ERR-LIST-ACM.pdf - 第21页
1320 Failed to restore board location data, defaults loaded - First startup after new software installation or startup after a forced shutdown (power-dip). - Don't switch to simulation mode before you start the mach…
1305
CA Camera %1 is not defined in
the SC configuration file
A conflict is detected in the
administration configuration files.
(System controller and process
controller files) - Illegal update of these configuration files. - Re-configure item.
1306
CA Camera %1 has conflicting
types in SC (%2) and APC (%3)
configuration
A conflict is detected in the
administration configuration files.
(System controller and process
controller files) - Illegal update of these configuration files. - Re-configure item.
1307
CA Camera %1 is not defined in
the APC configuration file
A conflict is detected in the
administration configuration files.
(System controller and process
controller files) - Illegal update of these configuration files. - Re-configure item.
1308
FA Camera %1 is not defined in
the SC configuration file
A conflict is detected in the
administration configuration files.
(System controller and process
controller files) - Illegal update of these configuration files. - Re-configure item.
1309
FA Camera %1 has conflicting
types in SC (%2) and APC (%3)
configuration
A conflict is detected in the
administration configuration files.
(System controller and process
controller files) - Illegal update of these configuration files. - Re-configure item.
1310
FA Camera %1 is not defined in
the APC configuration file
A conflict is detected in the
administration configuration files.
(System controller and process
controller files) - Illegal update of these configuration files. - Re-configure item.
1311
Coplanarity unit is not defined in
the APC configuration file
A conflict is detected in the
administration configuration files.
(System controller and process
controller files) - Illegal update of these configuration files. - Re-configure item.
1312
Coplanarity unit is not defined in
the SC configuration file
A conflict is detected in the
administration configuration files.
(System controller and process
controller files) - Illegal update of these configuration files. - Re-configure item.
1315
Hdrive setting mismatch between
SC and APC
A conflict is detected in the
administration configuration files.
(System controller and process
controller files) - Illegal update of these configuration files. - Re-configure item.
1316
Failed to restore configuration
data, defaults loaded
1317
Failed to restore set-up data,
defaults loaded
1318
Failed to restore action spec data,
defaults loaded
1319
Failed to restore machine data,
defaults loaded
System could not restore machine
data, defaults used instead.
- First startup after new software installation or startup after a
forced shutdown (power-dip). - Check and correct machine data.
1320
Failed to restore board location
data, defaults loaded
- First startup after new software installation or startup after a
forced shutdown (power-dip). - Don't switch to simulation mode before you start the machine.
1321 Failed to retrieve vision data
When starting-up the machine, the
vision-system could not get all
necessary data from the APC.
- One of the vision files is not correct, it may contain bad
characters or missing information. - Locate the bad vision file, and correct it.
1322
Failed to restore timer data,
defaults loaded
1323
Failed to restore error messages
1324
Failed to configure transport
controller
1325
Failed to retrieve toolbit data
1326
Failed to retrieve order data
1327
Unable to set date/time
1329
Toolbit exchange unit %1 is not
defined in the APC configuration
file
A conflict is detected in the
administration configuration files.
(System controller and process
controller files) - Illegal update of these configuration files - Re-configure item.
1331
Toolbit exchange unit %1 is not
defined in the SC configuration file
A conflict is detected in the
administration configuration files.
(System controller and process
controller files) - Illegal update of these configuration files. - Re-configure item.
1332
Unable change control state
because existing state is HOST -
OFFLINE.
Existing control state is preventing
the request for new control state to
be sent. Existing control state is host - offline. Wait for for the host to go online and try again.
1400 Refresh calibration requested.
A refresh calibration should be
executed, to assure accuracy. - Possible changes in machine base.
- Execute refresh calibration.
- NOTE: Do not clear this message before completion of the action.
1401 Timer for %1 has expired
The timer for the specified flux
applicator has expired.
- The pot lifetime for specified flux applicator has been
exceeded. - Replace flux.
1402 Timer for %1 has expired
The timer for the specified flux
applicator has expired.
- The pot lifetime for specified flux applicator has been
exceeded. - Replace flux.
1403 Timer for %1 has expired
The timer for the specified flux
applicator has expired.
- The pot lifetime for specified flux applicator has been
exceeded. - Replace flux.
1404 Timer for %1 has expired
The timer for the specified flux
applicator has expired.
- The pot lifetime for specified flux applicator has been
exceeded. - Replace flux.
1500
Process
1501
Machine
1502
Transport
1503
Coplanarity
1504
Head 1
1505
Head 2
1506
Head 3
1507
Head 4
1508
Feeder Section 1
1509
Feeder Section 2
1510
Feeder Section 3
1511
Feeder Section 4
1512
Limms-X
1513
Limms-YR
1514
Limms-YL
1515
Limms supplies
1516
H-Drive
1517
SBIP
1518
CA (Front)
1519
CA (Rear)
1520
FA (Front)
1521
FA (Rear)
1522
CA (Front-Left)
1523
CA (Front-Right)
1524
CA (Rear-Right)
1525
CA (Rear-Left)
1526
Dump 1
1527
Dump 2
1528
Dump 3
1529
Dump 4
1532
Cover (Front)
1533
Cover (Rear)
1534
Cover
1535
Therm. switch
1536
E-Stop (Front)
1537
NOT USED
1538
E-Stop (Rear)
1539
Feeder Section 1
1540
Feeder Section 2
1541
Feeder Section 4
1542
Feeder Section 3
1543
%?
1544
outer
1545
inner
1546
Initializing communication....
1547
Uploading vision files....
1548
Initializing....
1549
%1:Automatic retry on pick error
Only used in MIS reports.
1550
%1:Automatic retry on CA error
(including dump and repick) Only used in MIS reports.
1551
%1 :\tAutomatic retry FA (Spare
measured) Only used in MIS reports.
1552
Flux applicator (Front-Left)
1553
Flux applicator (Front-Right)
1554
Flux applicator (Rear-Right)
1555
Flux applicator (Rear-Left)
1556
RVS
1558
TEU (Rear)
1560
TEU (Front)
1561
Feeder Section 5
1562
Feeder Section 5
1600 SVS :\tUndefined error The SVS error is not defined yet. Unknown.
- Retry and continue.
- Report error to your service representative.
1601 SVS :\tUndefined warning
The SVS warning is not defined
yet. Unknown.
- Retry and continue.
- Report warning to your service representative.