773564-01_861-862-865_mounting_instructions_en_ge_ch.pdf - 第19页

FCC compliance Applicable only for encoders with ADS Uptime Bluetooth functionality . This equipment has been tested and found to com- ply with the limits for a Class B digital device , pur- suant to Part 15 of the FCC R…

Leine Linde products conform to several standards

and approvals. Certificates and documentation may

be provided upon request to your local Leine Linde

representative.

8.1 UL/CSA standards, type approval

Most Leine Linde products have been type

tested in accordance with IEC 61010. The product

box label states if the product conforms to the

standard. When the product is to be operated

in accordance with IEC 61010-1, the power must

be supplied from an isolated secondary circuit

with current or energy or power limitation as

per IEC 61010-1, IEC 60950-1, or by a class 2

secondary circuit as specified in UL 1310.

8.2 CE marking and Declaration of conformity

Most Leine Linde products conform to the

protection requirements of Council Directive

2014/30/EU related to EMC when applicable.

The product box label states if the product

conforms to the standard.

8.1)

8.2)

Certicates and

approvals

FCC compliance

Applicable only for encoders with ADS Uptime

Bluetooth functionality.

This equipment has been tested and found to com-

ply with the limits for a Class B digital device, pur-

suant to Part 15 of the FCC Rules. These limits are

designed to provide reasonable protection against

harmful interference in a residential installation.

This equipment generates, uses and can radiate

radio frequency energy and, if not installed and

used in accordance with the instructions, may cause

harmful interference to radio communications.

However, there is no guarantee that interference

will not occur in a particular installation. If this

equipment does cause harmful interference to radio

or television reception, which can be determined

by turning the equipment off and on, the user is

encouraged to try to correct the interference by one

or more of the following measures:

• Reorient or relocate the receiving antenna

• Increase the separation between the equipment

and receiver

• Connect the equipment into an outlet on a circuit

different from that to which the receiver is

connected

• Consult the dealer or an experienced radio/TV

technician for help

To satisfy FCC RF Exposure requirements for mobile

and base station transmission devices, a separation

distance of 20 cm or more should be maintained

between the antenna of this device and persons

during operation. To ensure compliance, operation at

closer than this distance is not recommended. The

antenna(s) used for this transmitter must not be co-

located or operating in conjunction with any other

antenna or transmitter.

Produkte von Leine Linde erfüllen die Auflagen einer

Reihe von Normen und Zulassungen. Auf Anfrage

sind Zertifikate und Dokumentation beim Leine Linde-

Vertreter in Ihrer Nähe erhältlich.

8.1 Zulassung gemäß UL-/CSA-Normen

Die meisten Produkte von Leine Linde wurden

gemäß IEC 61010 typgeprüft. Bei Verwendung

des Produkts gemäß IEC 61010-1 muss die

Spannungsversorgung aus einem isolierten

Sekundärkreis mit Strom-, Energie- oder Leis-

tungsbegrenzung nach IEC 61010-1, IEC 60950-1,

bzw. aus einem Sekundärkreis der Klasse 2 nach

UL 1310 erfolgen.

8.2 CE-Kennzeichnung und Konformitätserklärung

Die meisten Produkte von Leine Linde erfüllen

die EMV-Sicherheitsanforderungen gemäß Richt-

linie 2014/30/EU (sofern anwendbar). Auf der

Produktverpackung ist angegeben, ob das Produkt

der jeweiligen Norm entspricht.

8.1)

8.2)

Zertikate und

Zulassungen