Specification SIPLACE X-Series S 规格说明书.pdf - 第16页
16 Placement heads SIPLACE MultiStar (CPP) SIPLACE MultiStar (CPP) With component camera type 30 With compo nent camera type 33 (stationary camera) Component range a a) Please note that the placeable component range is a…
15
Placement heads
SIPLACE SpeedStar (C&P20 P2)
SIPLACE SpeedStar(C&P20 P2)
With component camera type 48
Component range
a
a) Please note that the placeable component range is also affected by the pad geometry, the customer-
specific standards, the component packaging tolerances and the component tolerances.
0.12 mm x 0.12 (0201 metric) to 2220, Melf, SOT, SOD, Bare-
Die, Flip-Chip
Component spec.
Max. height
Min. lead pitch
Min. lead width
Min. ball pitch
Min. ball diameter
Min. dimensions
Max. dimensions
Max. weight
4 mm
70 µm
30 µm
100 µm
50 µm
0.12 mm x 0.12 mm
8.2 mm x 8.2 mm
1 g
Set-down force 1.3 N ± 0.5N (default value)
0.5 N - 4.5 N
Touchless Placement
Nozzle types 60xx
X/Y accuracy
b
b) The accuracy values fulfill the conditions in the SIPLACE scope of supply and services.
± 34 µm/3σ
Angular accuracy ± 0.5° / 3σ
Illumination levels 5
16
Placement heads
SIPLACE MultiStar (CPP)
SIPLACE MultiStar (CPP)
With component camera
type 30
With component camera
type 33
(stationary camera)
Component range
a
a) Please note that the placeable component range is also affected by the pad geometry, the customer-
specific standards, the component packaging tolerances and the component tolerances.
01005 to 27 mm x 27 mm
0402 to 50 mm x 40 mm
b
b) A diagonal of 69 mm is possible during multiple measurements (e.g. 60 mm x 10 mm).
Component spec.
Max height
c
Max. height
d
Min. lead pitch
Min. lead width
Min. ball pitch
Min. ball diameter
Min. dimensions
Max. dimensions
Max. weight
c) CPP head: in low installation position (stationary component camera not possible).
d) CPP head: In high installation position
6.0 mm
8.5 mm
250 µm
100 µm
e
/ 200 µm
f
250 µm
e
/ 350 µm
140 µm
e
/ 200 µm
f
0.4 mm x 0.2 mm
27 mm x 27 mm
4 g
g
e) For components < 18 mm x 18 mm.
f) For components ≥ 18 mm x18 mm.
g) 20 g in "Pick&Place" mode
11.5 mm / 15.5 mm
h
300 µm
150 µm
350 µm
200 µm
1.0mm x 0.5mm
50 mm x 40 mm
8 g
g
h) 15.5 mm only in top assembly position, with OSC package and restrictions. See also the OSC package
on page 43.
Set-down force 1.0 - 15 N
i
i) 10 N standard, with OSC package 15 N.
Nozzle types 20xx, 28xx
X/Y accuracy
j
j) The accuracy values fulfill the conditions in the SIPLACE scope of supply and services.
± 38 µm/3σ ± 30 µm/3σ
Angular accuracy ± 0.20° / 3σ
k
, ± 0.38° / 3σ
l
k) Component dimensions between 6 mm x 6 mm and 27 mm x 27 mm.
l) Component dimensions smaller than 6 mm x 6 mm.
± 0.12° / 3σ
Illumination levels 5 6
17
Placement heads
SIPLACE TwinStar (TH)
SIPLACE TwinStar
With component camera type 33
(fine pitch camera)
With component camera type 25
(flip chip camera)
Component range
a
a) Please note that the placeable component range is also affected by the pad geometry, the customer-specific standards,
the component packaging tolerances and the component tolerances.
0402 to SO, PLCC, QFP, BGA, special
components, bare dies, flip-chips
0201 to SO, PLCC, QFP, sockets,
plugs, BGA, special components, bare
dies, flip-chips, shields
Component specs
b
Max. height
Min. lead pitch
Min. lead width
Min. ball pitch
Min. ball diameter
Min. dimensions
Max. dimensions
Max. weight
c
b) If the MultiStar and TwinStar are combined in the same placement area, the maximum component height may be re-
stricted.
c) Component plus nozzle or gripper.
25 mm (higher available on request)
300 µm
150 µm
350 µm
200 µm
1.0 mm x 0.5 mm
55 mm x 45 mm (single measurement)
Up to
200 mm x 110 mm (multiple measure-
ment)
d
160 g
e
d) Further restrictions will apply, according to the component dimensions and the component supply. These will be auto-
matically taken into account by SIPLACE Pro.
e) Up to 100 g is standard. Over 100 g available with reduced acceleration.
25 mm (higher available on request)
250 µm
100 µm
140 µm
80 µm
0.6 mm x 0.3 mm
16 mm x 16 mm (single measurement)
Up to
55 mm x 55 mm (multiple measure-
ment)
d
160 g
e
Set-down force 1.0 N - 30 N
f
f) 15 N standard, with OSC package 30 N.
Nozzle types
g
g) Over 300 different nozzles and 100 gripper types are available, with an extensive nozzle database available online.
5xx (standard)
20xx/28xx + adapter
9xx + adapter
Gripper
Nozzle spacing for P&P
heads
70.8 mm
X/Y accuracy
h
h) The accuracy values fulfill the conditions in the SIPLACE scope of supply and services.
± 26 µm/3σ ± 22 µm/3σ
Angular accuracy ± 0.05° / 3σ, ± 0.05° / 3σ
Illumination levels 6 6