Specification SIPLACE X-Series S 规格说明书.pdf - 第17页
17 Placement heads SIPLACE TwinStar (TH) SIPLACE T winSt ar With component c amera type 33 (fine pitch camera) With co mponent came ra type 2 5 (flip chip camera) Component range a a) Please note that the placeable compo…
16
Placement heads
SIPLACE MultiStar (CPP)
SIPLACE MultiStar (CPP)
With component camera
type 30
With component camera
type 33
(stationary camera)
Component range
a
a) Please note that the placeable component range is also affected by the pad geometry, the customer-
specific standards, the component packaging tolerances and the component tolerances.
01005 to 27 mm x 27 mm
0402 to 50 mm x 40 mm
b
b) A diagonal of 69 mm is possible during multiple measurements (e.g. 60 mm x 10 mm).
Component spec.
Max height
c
Max. height
d
Min. lead pitch
Min. lead width
Min. ball pitch
Min. ball diameter
Min. dimensions
Max. dimensions
Max. weight
c) CPP head: in low installation position (stationary component camera not possible).
d) CPP head: In high installation position
6.0 mm
8.5 mm
250 µm
100 µm
e
/ 200 µm
f
250 µm
e
/ 350 µm
140 µm
e
/ 200 µm
f
0.4 mm x 0.2 mm
27 mm x 27 mm
4 g
g
e) For components < 18 mm x 18 mm.
f) For components ≥ 18 mm x18 mm.
g) 20 g in "Pick&Place" mode
11.5 mm / 15.5 mm
h
300 µm
150 µm
350 µm
200 µm
1.0mm x 0.5mm
50 mm x 40 mm
8 g
g
h) 15.5 mm only in top assembly position, with OSC package and restrictions. See also the OSC package
on page 43.
Set-down force 1.0 - 15 N
i
i) 10 N standard, with OSC package 15 N.
Nozzle types 20xx, 28xx
X/Y accuracy
j
j) The accuracy values fulfill the conditions in the SIPLACE scope of supply and services.
± 38 µm/3σ ± 30 µm/3σ
Angular accuracy ± 0.20° / 3σ
k
, ± 0.38° / 3σ
l
k) Component dimensions between 6 mm x 6 mm and 27 mm x 27 mm.
l) Component dimensions smaller than 6 mm x 6 mm.
± 0.12° / 3σ
Illumination levels 5 6
17
Placement heads
SIPLACE TwinStar (TH)
SIPLACE TwinStar
With component camera type 33
(fine pitch camera)
With component camera type 25
(flip chip camera)
Component range
a
a) Please note that the placeable component range is also affected by the pad geometry, the customer-specific standards,
the component packaging tolerances and the component tolerances.
0402 to SO, PLCC, QFP, BGA, special
components, bare dies, flip-chips
0201 to SO, PLCC, QFP, sockets,
plugs, BGA, special components, bare
dies, flip-chips, shields
Component specs
b
Max. height
Min. lead pitch
Min. lead width
Min. ball pitch
Min. ball diameter
Min. dimensions
Max. dimensions
Max. weight
c
b) If the MultiStar and TwinStar are combined in the same placement area, the maximum component height may be re-
stricted.
c) Component plus nozzle or gripper.
25 mm (higher available on request)
300 µm
150 µm
350 µm
200 µm
1.0 mm x 0.5 mm
55 mm x 45 mm (single measurement)
Up to
200 mm x 110 mm (multiple measure-
ment)
d
160 g
e
d) Further restrictions will apply, according to the component dimensions and the component supply. These will be auto-
matically taken into account by SIPLACE Pro.
e) Up to 100 g is standard. Over 100 g available with reduced acceleration.
25 mm (higher available on request)
250 µm
100 µm
140 µm
80 µm
0.6 mm x 0.3 mm
16 mm x 16 mm (single measurement)
Up to
55 mm x 55 mm (multiple measure-
ment)
d
160 g
e
Set-down force 1.0 N - 30 N
f
f) 15 N standard, with OSC package 30 N.
Nozzle types
g
g) Over 300 different nozzles and 100 gripper types are available, with an extensive nozzle database available online.
5xx (standard)
20xx/28xx + adapter
9xx + adapter
Gripper
Nozzle spacing for P&P
heads
70.8 mm
X/Y accuracy
h
h) The accuracy values fulfill the conditions in the SIPLACE scope of supply and services.
± 26 µm/3σ ± 22 µm/3σ
Angular accuracy ± 0.05° / 3σ, ± 0.05° / 3σ
Illumination levels 6 6
18
Placement heads
Nozzle changer
Nozzle changer for the SIPLACE SpeedStar (C&P20 P2)
Nozzle changer for the SIPLACE MultiStar CPP
Nozzle changer for the SIPLACE TwinStar
4 magazines for 20 nozzles
of type 60xx
6 magazines for 20 nozzles of
type 60xx
1 magazine for 9 nozzles of
type 28xx
3 magazines for 20 nozzles of type 20xx
1 magazine for 9 nozzles of
type 28xx
5 magazines for 20 nozzles of type 20xx
Magazine for two standard nozzles
Magazine for one special nozzle, gripper
Description
Nozzle changers increase the flexibility of the placement heads when it comes to processing
different components. The nozzle configuration can be rapidly adjusted to changing place-
ment jobs. Precisely defined positions and perfect nozzle seat in the garage ensure minimum
radial eccentricity on the placement head.
The nozzle changers feature a monitoring circuit.This checks whether the nozzle magazines
are seated correctly on the mount. In addition, the nozzle changers recognize whether the
magazines are for 40xx/60xx, 20xx or 28xx nozzles by the code.