00197623-03_VD_708.1_SP2_DE_EN.pdf - 第23页
Station Software 7 08.1 SP2 / Version Description Ausgabe 10/2015 E dition 23 Fast head exchang e – The function only sup ports the C&P 20A and CPP placement heads. – Stationary camera s will always be cali brated. –…
Station Software 708.1 SP2 / Version Description Ausgabe 10/2015 Edition
22
VHF P&P head
Supported on the SX1/SX2 V2 placement machine only.
Reduced air consumption with vacuum pump
No support for CPP placement heads and Twin Head.
Automatic tray feeding
The function is not supported on the X4i, SX4 and DX4 placement machines.
Dip module LDU_X
– Parameterization in the component shape is not transferred to the LDU_X module. The
parameters have to be additionally set at the LDU_X module.
– Reduced LDU_X performance, as maximum 2 A can be provided for each feeder. Therefore
the drives of the LDU_X module cannot reach the maximum possible acceleration.
– LDU_X modules cannot be placed on any track of the X-table because of restrictions
concerning the accessibility with the twin head. The range of usable tracks for setting up
LDU_X modules is limited in SIPLACE Pro.
– LDU_X module and manual tray cannot be placed together on one table on the machine types
X2, X3, X4, X4i and SX4.
– The eSW of the LDU_X module can only be updated via notebook and serial interface.
– Maximum component dimension: 45 x 45 mm. For TwinHead: squeegee cycle between the two
dipping processes, if the components on both head segments have to be dipped.
– Setup verification is not supported with the LDU-X module.
– Reachability of the LDU_X module in the X-, SX- and DX-series:
X2: Location 1 and 3 39.5 mm
Location 2 and 4 54 mm
X3: Location 1 22.5 mm
Location 3 39.5 mm
Location 2 and 4 54 mm
X4: Location 1 and 3 C&P20/CPP, 38 mm
Location 2 und 4 no restriction
X4i: All Locations 38 mm of 75 mm
SX1/2 and DX1/2:
Location 1 or 2 inner position: no restriction
outer position: half of the dipping area
SX4 All Locations 38 mm of 75 mm
– Dipping with the C&P20A placement head is only possible with LDU_X as of function version 3.
Station Software 708.1 SP2 / Version Description Ausgabe 10/2015 Edition
23
Fast head exchange
– The function only supports the C&P20A and CPP placement heads.
– Stationary cameras will always be calibrated.
– A placement head should always be replaced by a placement head of the same type. If a
placement head is replaced by another head type, the fast exchange time is not granted, as
configuration changes, setup change and hardware exchange will follow.
– A manual head exchange is not detected (e.g. if a placement head is manually disassembled
and identically reassembled during maintenance).
Virtual PCB stack
– The boards will only be placed if the corresponding "PCB Detection Inkspots" is detected.
– No plausibility check is performed. I.e., if both inkspots are detected by mistake, both board
contents will be placed. If neither of the two inkspots is detected, no placement will be
performed.
Rotational angle compensation for short, wide boards
After the station software has been shut down, the start offset is not available anymore.
WPC5 / WPC 6
– WPC5: Non Stop operation is not supported.
– WPC5: When the station software is booted it is not detected whether a WPC is connected, as
the WPC has a power supply of its own. Therefore, a reference run can only be prevented by
pressing the emergency stop button. It is recommended to switch on the WPC before the
placement machine.
– Components up to a height of 30mm can be placed with a force of 70N with the WPC5 as of
serial number 1485 and the WPC6 as of serial number C1486 only.
– Components up to a height of 40mm can be placed with the WPC5 as of serial number B3000
and the WPC6 as of serial number C3000.
– Due to the refill module, components > 25mm cannot be positioned on the levels 1 – 3 and
27 – 28 on the WPC6. The levels 4 – 28 will be set up automatically by the SIPLACE Pro
Optimizer. The levels 1 – 3 have to be blocked manually by the operator.
CPP/Twin Head/VHF P&P/Twin VHF or C&P12/Twin Head/VHF P&P/Twin VHF placement
heads and high components in asynchronous dual lane transport mode
Due to the differing "free height" of the placement heads when combining the placement head
types in the processing area, already placed components might be damaged in the following cases:
– During auto recovery, when the board to be recovered is already placed with high components.
– By going to service position.
– During a manually activated refererence run.
– During manual operations, teaching and inspection of placed components with the board
camera. In these cases also components in the opposing trays (WPC/MTC) might be
damaged.
– By using the Long board option.
Station Software 708.1 SP2 / Version Description Ausgabe 10/2015 Edition
24
Station-wise download
– It is not possible to switch over from dual lane conveyor in asynchronous transport mode to
dual lane conveyor in synchronous transport mode (and vice versa) in combination with station-
wise download.
– With dual lane conveyor in asynchronous transport mode, station-wise download is only
possible with a setup change if a recipe is specified for both conveyor lanes simultaneously.
– Station-wise download is canceled if the Line Control Server is shut down and rebooted. After
the Line Control Server has been rebooted, production can only continue after a complete line
download.
Manual conveyor width adjustment via Line Control
For the placement machines with platform 2+ software the conveyor width could be manually
defined by Line Control, because an automatic width adjustment was impossible in barcode
controlled production.
In the 70x station software the conveyor width is always automatically adjusted through SIPLACE
Pro, also in barcode controlled production. Manual conveyor width adjustment via Line Control is
not possible for placement machines with 70x station software.
Long Board option
– If the Long Board option is defined in the setup:
No mix of two different stop positions or long and short boards (in barcode mode or placement
based on ink spots in a job). This applies to all machine types.
– The default stopper must not be removed on the conveyor.
Automatic exchange of defective nozzles
Part of the reference run and the production only. The feature is ignored during component
teaching.
Automatic recognition of feeder pitch
– Track-empty errors are not recognized.
– Only possible, if a direct component recognition through a vacuum or a component sensor is
set in SIPLACE Pro.
– When single functions are used simultaneously (e.g. component or component shape teaching)
not every pick-up trial will be successful.
Barcode controlled production
– Only recipes with the same setup can be combined to a barcode controlled production job.
– Only the complete setup is displayed. A selective display of the setup used by the current
defined recipe is not supported. However, a selective display exists, displaying which feeders
are needed by the currently produced boards. If there is no board in the machine, the feeders
which were needed by the last placed board on both tracks respectively are displayed.
– All defined board types must have the same width in barcode controlled production.
– Only the barcode scanner at the conveyor belt or a whispered barcode is used, but not a
barcode read by the PCB camera.