00193733-02.pdf - 第47页
SIPLACE F5 HM 2 Assembly Instructions PCB Camera, Multicolor SIPLACE F5 HM 05/2007 Edition 2.1 Overview 47 2 Assembly Instructions PCB Camera, Multicolor SIPLACE F5 HM 2.1 Overview These instructions describe how to asse…
1 Montageanleitung LP-Kamera Multicolor SIPLACE F5 HM SIPLACE F5 HM
1.13 Anhang: Platinen, Kabel und Schaltpläne Ausgabe 05/2007
46
SIPLACE F5 HM 2 Assembly Instructions PCB Camera, Multicolor SIPLACE F5 HM
05/2007 Edition 2.1 Overview
47
2 Assembly Instructions PCB Camera,
Multicolor SIPLACE F5 HM
2.1 Overview
These instructions describe how to assemble the optional "PCB Camera Multicolor" on SIPLACE
F5 HM.
The optional PCB camera Multicolor is used in place of the subgantry camera (PCB camera with
normal light) AND the optional oblique illumination. It is utilized to improve the recognition of fidu-
cials (reference marks) and therefore to achieve greater accuracy during placement.
With the PCB camera Multicolor it is possible to acquire at least the entire range of fiducials cur-
rently recognizable with normal or oblique illumination.
Only the Siemens SMD service engineer is authorized to carry out the assembly.
The PCB camera Multicolor is only to be operated after it has been properly installed (see
Abschn. 2.2.2).
– Software version 407.01 or later is a requirement.
– On machines manufactured from Sep 98 to Dec 98 a DIN mounting rail (top-hat rail) has to
be installed on the RH side of the terminal panel. This rail is not included in the assembly
kit. For details, see Section 2.4.4.1.
– Following approximate values are intended to help you ascertain the total time required:
- 0.5 hr. per placement head for exchanging the PCB camera
- 1.0 hr. per machine for wiring.
- 0.5 hr. for configuration at the line computer and in the SITEST and setting of the illu-
mination on the station.
- 2.0 hr. to calibrate placement head, IC head and cameras via SITEST.
NOTE
It is only necessary to use the "new" head cover (with bulge or - as a preliminary solution - a cutout
for the IC camera 16 x 16) if the FC camera 16 x 16 is on or is being installed on the 6-segment
revolver head (SP 6). For this reason the new head cover is included in the assembly kit of the
FC camera 16 x 16.
Without FC camera 16 x 16, the old head cover can be re-used if the cables of PCB camera Mul-
ticolor have been run as described here. 2
2 Assembly Instructions PCB Camera, Multicolor SIPLACE F5 HM SIPLACE F5 HM
2.2 Safety Instructions 05/2007 Edition
48
2.2 Safety Instructions
2.2.1 Safety Instructions for assembly
DANGER
Only Siemens service engineers are permitted to perform the assembly of the "PCB camera Mul-
ticolor". Comply with the higher ranking "Safety Instructions" in Chapter "Operational Safety" in
the User Manual and Service Manual.
The machine SIPLACE F5 HM is powered by line voltage.
Portions of the system are therefore conducting dangerous electricity, inside the machine even
while the master switch is turned off.
After you have properly carried out the shut-down of the Windows operating system NT:
before all work the machine must be turned OFF at the main switch and isolated from the mains.
In addition, the compressed air supply must be turned off at the main valve of the compressed air
unit in the machine base and the compressed air lines must be bled by actuating the needle valve
at the compressed air unit (particularly due to the risk of injury - posed by residual air - at the pneu-
matic cutter after undocking/removing the component changeover table).
Obey the applicable accident prevention regulations, DIN standards and special safety codes of
your country at all times. DIN EN 60204 must be adhered to during all work inside the machine
base.
Follow the instructions regarding residual voltages in Chapter "Operational Safety".
Comply with regulations on ESDs (see Chapter "Operational Safety").
During the work of assembly secure the machine conscientiously against other personnel and pre-
vent it from being turned back on without authorization, as described in the User Manual in the
chapter "Locking the Machine...".
There is additional, higher risk of accident when working with the SITEST program.
The SITEST program is only to be started by personnel who are authorized to do so.
For the work with the SITEST program the component changeover table must be moved in and
correctly connected. 2