00193733-02.pdf - 第61页
SIPLACE F5 HM 2 Assembly Instructions PCB Camera, Multicolor SIPLACE F5 HM 05/2007 Edition 2.6 Assembly Term inal pan els and Illumination cable 61 : Use the table to determ ine whether the distance plate is required . I…
2 Assembly Instructions PCB Camera, Multicolor SIPLACE F5 HM SIPLACE F5 HM
2.6 Assembly Terminal panels and Illumination cable 05/2007 Edition
60
Abb. 2.6.6 PCB Camera Multicolor Assembly with Distance Plate (Spacer)
Key: 2
1. Distance plate (Spacer) *)
2. PCB camera Multicolor incl. cable and connector *)
3. Fasteners for PCB camera Multicolor: 3 hex head cap screws M3 x 14, captive *)
4. "PCB camera board, modular" *)
5. Cable "illumination", camera *) -> Connection to X3 at "PCB (camera) board modular"
6. Cable "camera" *) -> Connection to X4 at "Vision board, modular"
*) Components of the assembly kit PCB camera Multicolor
NOTE.
PCB camera Multicolor and "PCB camera board, modular," constitute a mutually attuned unit. 2
: When removing the components from the package for the first time, check to make certain that
the serial number on the camera is identical with the number on the "PCB camera board, mo-
dular" (see Abb. 2.6.8).
: Beginning from the bottom of the gantry, screw the 3 new spacer bolts (L = 8.5 mm) from the
assembly kit into the camera holder (6 mm open-end / socket wrench).
: Ascertain the PCB/substrate thickness to be processed now.
2
1
3
4
5
6
SIPLACE F5 HM 2 Assembly Instructions PCB Camera, Multicolor SIPLACE F5 HM
05/2007 Edition 2.6 Assembly Terminal panels and Illumination cable
61
: Use the table to determine whether the distance plate is required.
If yes, place the distance plate (see Abb. 2.6.6 -> 1) from the camera assembly kit on the ca-
mera’s assembly surface in the correct rotational position (this is determined on the basis of
the holes).
Abb. 2.6.7 Fastening the PCB Camera Multicolor (View from below, diagonally)
Key: 2
1.PCB camera Multicolor
2. Fasteners: 3 hex head cap screws M3 x 14 (captive)
3. 2 Cable ties
2
: Place the PCB camera Multicolor, including the distance plate, if applicable, in the correct po-
sition on the distance bolts (HS-50) or directly on the camera holder from below (S-25 HM).
: Use the 3 captive hex head cap screws M 3 x 14 to screw the camera to the camera holder.
: Fasten the cables with the two cable ties (see 2.6.7).
2
2
21
3
2 Assembly Instructions PCB Camera, Multicolor SIPLACE F5 HM SIPLACE F5 HM
2.6 Assembly Terminal panels and Illumination cable 05/2007 Edition
62
2.6.5 Installing the "PCB Camera Board, Modular" from the assembly kit
NOTE
The "PCB camera board, modular", is attuned to the pertinent PCB camera Multicolor. 2
: Check the serial number of the PCB camera board, modular:
It must correspond to the number on the Multicolor PCB camera.
Per gantry this allocation must be maintained during installation.
The position of the number is shown in the following illustration.
Abb. 2.6.8 Check: Identical Serial Number on Modular PCB Camera Board and PCB Camera Multicolor
2
: Plug the "PCB camera board, modular" onto the "Vision board, modular" in the correct position,
as shown above.
The contact jack on the bottom of the PCB camera board must move all the way into the con-
nector of the vision board.
: It is necesssary, that you control the correct mounting position of the "Vision-Board modular".
20002