00193733-02.pdf - 第60页

2 Assembly Instructions PCB Camera, Multicolor SIPLACE F5 HM SIPLACE F5 HM 2.6 Assembly Terminal panels and Illumination cable 05/2007 Edition 60 Abb. 2.6.6 PCB Camera Multicolor Assembly with Distance Plate (Spacer) Key…

SIPLACE F5 HM 2 Assembly Instructions PCB Camera, Multicolor SIPLACE F5 HM

05/2007 Edition 2.6 Assembly Terminal panels and Illumination cable

: Set the PCB camera down carefully so that it won’t be damaged. The best procedure is to place

it in a suitable package immediately.

2.6.4 Installing the PCB Camera Multicolor

NOTE:

Find out before installing the PCB camera Multicolor which PCB or substrate thickness will be

place next. Depending on the thickness, it will or will not be necessary to place the distance plate

(spacer) from the assembly kit under each camera.

The table below is helpful during assembly process. In deciding, calculations are carried out to

ascertain which thickness range the current PCB or substrate thickness is closest to the FOCUS.

Following the configuration of the Multicolor PCB camera at the line computer, including descri-

bing the PCB or substrate (entry of the thickness), a message can be accessed at the line com-

puter as a check (see Abschn. 2.7.2).

If the distance plates are not required at the present time, make certain that they are stored such

that they will be available to the line engineer/service engineer for later installation. 2

The following data items are recommendations to ensure an optimal placement process: 2

In most cases, adequate imaging quality will still be achieved even it work is done outside the ran-

ges indicated above.

With the spacer plate removed, system fiducials can still be adequately recognized. 2

PCB or substrate thickness Focus Install distance plate (spa-

cer)

0.3 - 3.4 mm 1.7 mm Yes

1.5 - 4.5 mm 3.2 mm No

2 Assembly Instructions PCB Camera, Multicolor SIPLACE F5 HM SIPLACE F5 HM

2.6 Assembly Terminal panels and Illumination cable 05/2007 Edition

Abb. 2.6.6 PCB Camera Multicolor Assembly with Distance Plate (Spacer)

Key: 2

1. Distance plate (Spacer) *)

2. PCB camera Multicolor incl. cable and connector *)

3. Fasteners for PCB camera Multicolor: 3 hex head cap screws M3 x 14, captive *)

4. "PCB camera board, modular" *)

5. Cable "illumination", camera *) -> Connection to X3 at "PCB (camera) board modular"

6. Cable "camera" *) -> Connection to X4 at "Vision board, modular"

*) Components of the assembly kit PCB camera Multicolor

NOTE.

PCB camera Multicolor and "PCB camera board, modular," constitute a mutually attuned unit. 2

: When removing the components from the package for the first time, check to make certain that

the serial number on the camera is identical with the number on the "PCB camera board, mo-

dular" (see Abb. 2.6.8).

: Beginning from the bottom of the gantry, screw the 3 new spacer bolts (L = 8.5 mm) from the

assembly kit into the camera holder (6 mm open-end / socket wrench).

: Ascertain the PCB/substrate thickness to be processed now.

SIPLACE F5 HM 2 Assembly Instructions PCB Camera, Multicolor SIPLACE F5 HM

05/2007 Edition 2.6 Assembly Terminal panels and Illumination cable

: Use the table to determine whether the distance plate is required.

If yes, place the distance plate (see Abb. 2.6.6 -> 1) from the camera assembly kit on the ca-

mera’s assembly surface in the correct rotational position (this is determined on the basis of

the holes).

Abb. 2.6.7 Fastening the PCB Camera Multicolor (View from below, diagonally)

Key: 2

1.PCB camera Multicolor

2. Fasteners: 3 hex head cap screws M3 x 14 (captive)

3. 2 Cable ties

: Place the PCB camera Multicolor, including the distance plate, if applicable, in the correct po-

sition on the distance bolts (HS-50) or directly on the camera holder from below (S-25 HM).

: Use the 3 captive hex head cap screws M 3 x 14 to screw the camera to the camera holder.

: Fasten the cables with the two cable ties (see 2.6.7).