CP7 training(6.0) (1).pdf - 第17页

FK-9F98-27 CP-7 Series T raini ng T ext for Service Engineers Edition 6.0 Chapter 3. X, Y , Z and D-axes Adjustm ent [3/36] 3.2.2 CP-732/733E X-axis Adjustme nt and Calibration Data Setting Equipment Checklist: 1- 7 N.m …

100%1 / 147
FK-9F98-27 CP-7 Series Training Text for Service Engineers
Edition 6.0 Chapter 3. X, Y, Z and D-axes Adjustment [2/36]
12. Set the + OT sensor so that it turns ON 2000 pulses back from the mechanical stopper. It
must be – 276000 +/- 1000 pulses.
13. Move the X-axis back 500 pulses from where the + OT sensor turns ON and set the Calibration
Data value. (Min Limit Position)
Press: [Maintenance] [Calibration] [Travel Limits] [Minimum Limit X]
14. Table 1 lists the X axis Calibration Data and physical data reference values:
CP-742/743(M)E
X Axis Calibration Data Item Reference Value (0.002mm/pulse)
+ Mechanical stopper 2500 +/- 100
OT sensor 500 +/- 100
Max Limit Position X (– OT – 500) 0 +/-100
PCB Check Position X (left to right m/c) – 190000
Loading Position XL IN – 271000
Loading Position XL OUT – 11250
Mark Read Position XC (left to right m/c) – 231000
Placing Position X0 (left to right m/c) – 270500
Minimum Limit Position X (+ OT + 500) – 275500 +/- 1000
+ OT sensor – 276000 +/- 1000
– Mechanical stopper – 278000 +/- 1000
Table 1
15. Check sensor reaction by I/O
<I/O Æ Servo Æ IN>
SX009 X AXIS +OT (X Plus OT)
SX00A X AXIS –OT (X Minus OT)
Fuji Machine Mfg. Co., Ltd. (Okazaki)
SMT Equipment Quality Assurance Dept.
CS Section
3-2
FK-9F98-27 CP-7 Series Training Text for Service Engineers
Edition 6.0 Chapter 3. X, Y, Z and D-axes Adjustment [3/36]
3.2.2 CP-732/733E X-axis Adjustment and Calibration Data Setting
Equipment Checklist:
1- 7 N.m torque wrench with 4mm attachment
1- Small size 4mm L-wrench with pipe
1- Small mirror
1- 3mm T-wrench
1- 155mm spacer jig (Jig No.:DCPJ0710)
1. Remove the minus OT sensor flag (right side).
2. Check that the coupling is loose then set the X axis pulse count to – 75000 pulses.
3. Place the 155mm spacing jig (Fig.2) between the X-axis + mechanical stopper and the X-axis
table. Tighten the coupling bolt with a 7N.m torque wrench.
Figure 2
X-Table
X-Motor
Spacing
Jig
Stopper
Coupling
4. Return the XY table to the + mechanical stopper and record the pulse count at this position. It
must be 2500 +/- 100 pulses.
5. Check the alignment of the OT sensor flags and OT sensors.
6. Set the – OT sensor so that it turns ON 2000 pulses back from the + mechanical stopper. It
must be 500 +/- 100 pulses.
7. Move the X-axis back 500 pulses from where the – OT sensor turns ON and set the
Calibration Data value. (Max Limit Position)
Press: [Maintenance] [Calibration] [Travel Limits] [Maximum Limit X]
8. Move the XY table to the – mechanical stopper and record the pulse count at this position. It
must be – 227500 +/- 1000 pulses.
9. Set the + OT sensor so that it turns ON 2000 pulses back from the mechanical stopper. It
must be – 225500+/- 1000 pulses.
10. Move the X-axis back 500 pulses from where the + OT sensor turns ON and set the
Calibration Data value. (Min Limit Position)
Press: [Maintenance] [Calibration] [Travel Limits] [Minimum Limit X]
Fuji Machine Mfg. Co., Ltd. (Okazaki)
SMT Equipment Quality Assurance Dept.
CS Section
3-3
FK-9F98-27 CP-7 Series Training Text for Service Engineers
Edition 6.0 Chapter 3. X, Y, Z and D-axes Adjustment [4/36]
11. Table 2 lists the X axis Calibration Data and physical data reference values:
CP-732/733E
X Axis Calibration Data Item
Reference Value (0.002mm/pulse)
+ Mechanical stopper 2500 +/- 100
– OT sensor 500 +/- 100
Max Limit Position X (– OT – 500) 0 +/-100
PCB Check Position X (left to right m/c) – 190000
Loading Position XL IN – 220500
Loading Position XL OUT – 11250
Mark Read Position XC (left to right m/c) – 180500
Placing Position X0 (left to right m/c) – 222500
Minimum Limit Position X (+ OT + 500) – 225000 +/- 1000
+ OT sensor – 225500 +/- 1000
– Mechanical stopper – 227500 +/- 1000
Table 2
12. Check sensor reaction by I/O
<I/O Æ Servo Æ IN>
SX009 X AXIS +OT (X Plus OT)
SX00A X AXIS –OT (X Minus OT)
Fuji Machine Mfg. Co., Ltd. (Okazaki)
SMT Equipment Quality Assurance Dept.
CS Section
3-4