00196622-03_OM_WPC5_6_EN.pdf - 第16页
Operational Safety Warning Labels 2.2.1 Warning Labels on the WPC5 and WPC6 16 Operating Manual SIPLACE WPC5/WPC6 2.2 2 . 2 W a r n in g L a b e ls Warning Labels 2.2.1 2 . 2 . 1 W a r n in g L a b e ls o n t h e W P C 5…
Operational Safety
2.1.2 Important Notes on Operational Safety Safety Instructions
Operating Manual SIPLACE WPC5/WPC6 15
► Instruct personnel about the significance and effects if warnings are not observed.
2.1.2.3
2.1.2.3 Safety of Plant and Equipment
Safety of Plant and Equipment
► Never make changes, however minor, unless you are totally aware of the effect they will have on the
overall functioning of the system.
► The stations must always be set up, retooled and maintained by appropriately trained personnel.
► Only use original spare parts and authorized accessories of SIPLACE. The use of other parts will
affect safety and will invalidate the liability for any consequential damage.
► Do not make modifications to the safety equipment. Never bridge protective switches or remove pro-
tective devices.
DANGER
The module is electrically driven. When electrical devices are in use, certain parts carry dan-
gerous voltage levels!
► Some assemblies inside the module are still live when the main switch is turned off and will
remain so until the module is disconnected from the power supply. Other electrical compo-
nents may have residual voltages. Wait for this to be discharged after the main switch has
been set to OFF. These components are all labeled appropriately.
► Before performing service work or certain maintenance tasks, switch the module off at the
main switch and disconnect the power cable form the power supply.
DANGER
In spite of all the safety precautions taken by the manufacturer, failure to use the module as
prescribed or incorrect maintenance, setting or service procedures can result in severe physical
injury (e.g. from lifting axis) and/or considerable damage to property. Safe operation of the mod-
ule and the safe performance of all work to the module requires that the operation/the work is
performed by appropriately qualified personnel in observance of all warnings.
Certain tasks performed on the machine (e.g. maintenance, setting up and service work) re-
quires training that goes beyond the scope of this manual.
Operational Safety
Warning Labels 2.2.1 Warning Labels on the WPC5 and WPC6
16 Operating Manual SIPLACE WPC5/WPC6
2.2
2.2 Warning Labels
Warning Labels
2.2.1
2.2.1 Warning Labels on the WPC5 and WPC6
Warning Labels on the WPC5 and WPC6
Overview
1. 1x warning W201 – safe operation of the machine
2. 1x label: crank handle attachment point
3. 2x label: fork-lift attachment points
4. 5x warning W206 - dangerous voltages
5. 1x label: ESD connection point
6. 1x warning 203 - danger of crushing
Overview
1. 2x warning label 207 - mains voltage
2. 2x warning 203 - danger of crushing
Operational Safety
2.2.2 Warning label at the Non-Stop Module (only WPC6) Warning Labels
Operating Manual SIPLACE WPC5/WPC6 17
2.2.2
2.2.2 Warning label at the Non-Stop Module (only WPC6)
Warning label at the Non-Stop Module (only WPC6)
2.2.3
2.2.3 Warning, Prohibition and Cautionary Labels
Warning, Prohibition and Cautionary Labels
2.2.4
2.2.4 Warning Label W201
Warning Label W201
2.2.5
2.2.5 Warning Label W203
Warning Label W203
Overview
1. 1x warning 203 - danger of crushing
WARNING
Do not use abrasive cleaners or solvents for cleaning warning labels.
Replace any damaged or illegible warning labels.
Check that the warning labels are positioned correctly.
SAFE OPERATION OF THE MACHINE
Safe operation of the machine depends absolutely on the operator being fa-
miliar with the operating manual and safety instructions and putting them
into effect.
Item no. 03009338-xx
DANGER OF CRUSHING!
Reaching in here can lead to injuries to the arms and hands.
Do not reach into the machine while it is running.
Item no. 03009342-xx