192866 Issue 4 - Reel to Reel Manual LoRes.pdf - 第20页
TECHNICAL REFERENCE ADJUSTMENTS AND SETTINGS 1.10 Reel to Reel Manual Chapter Issue 1, Apr 15 W ARNING BOARD CLAMPS. EXTREME CA RE MUST BE EXERCISED W HEN WORKING IN THE TOOLING AREA OF THE MACHINE TO A VOID INJUR Y . TH…
TECHNICAL REFERENCE
ADJUSTMENTS AND SETTINGS
Chapter Issue 1, Apr 15 Reel to Reel Manual 1.9
Product Guides
and Transport
Clamps
The product guides on the inroad and the transport clamps on the outroad are
adjusted to within 0.5mm of the product reel, Setup - Product Changeover in the
User chapter of this manual refers.
Transport Carriage
Belts
The position of the transport carriage belts is dependent on the product width,
the belts need to support the outer edges and centre. More transport carriage
belts may be fitted if the product reel is very thin and requires more support.
There are 11 possible positions for transport carriage belts, the front belt must
always remain in Position 1 to support the front of the product reel.
To reposition the transport carriage belts, use the following procedure:
1. Measure the width of the product reel.
2. Use the graphic and table below to determine the position for the rear and
centre transport carriage belts.
Product Reel Width Rear Belt Position Centre Belt Position
Greater than 440mm 11 5 or 6
398mm to 440mm 10 5
356mm to 397mm 9 4 or 5
314mm to 355mm 8 4
272mm to 313mm 7 3 or 4
230mm to 271mm 6 3
188mm to 229mm 5 2 or 3
146mm to 187mm 4 2
50mm to 145mm 3 2
7
8
9
10
11
4
5
6
1
2
3
TECHNICAL REFERENCE
ADJUSTMENTS AND SETTINGS
1.10 Reel to Reel Manual Chapter Issue 1, Apr 15
WARNING
BOARD CLAMPS. EXTREME CARE MUST BE EXERCISED WHEN WORKING IN
THE TOOLING AREA OF THE MACHINE TO AVOID INJURY. THE FOILS ON THE
FRONT AND REAR BOARD CLAMPS ARE VERY SHARP.
3. To move the position of a belt, slip the belt off the left and right belt pulleys.
4. Using a 3mm Allen key, remove the four belt clamp securing screws (two on
the right hand side of the inner transport vacuum plate and two on the left
hand side).
5. Fit the belt clamps to the new positions.
6. Fit the belt ends into the belt clamps ensuring the correct amount of belt is
protruding out of the bottom of the clamp, see table below:
7. Tighten the belt clamps.
Belt Position Dimension
Middle Belt 20mm below the clamp
Rear Belt 15mm below the clamp
Belt Clamps
Securing Screws
Transport Carriage Belt
Belt Pulley
(Left)
Belt Pulley
(Right)
TECHNICAL REFERENCE
ADJUSTMENTS AND SETTINGS
Chapter Issue 1, Apr 15 Reel to Reel Manual 1.11
8. Using a 2mm Allen key, loosen the two grub screws that secure the right
hand pulley to the drive shaft.
9. Repeat for the left hand pulley.
10. The pulleys must be aligned to the belt clamp position and the measurement
for the belt pulley is referenced from the centre of the pulley in Position 1.
11. Using a steel rule and measuring from the top of the belt on the pulley in
Position 1, use the table below to position the centre of the right hand pulley.
12. Tighten the two pulley grub screws.
13. Repeat Steps 11 and 12 for the left hand pulley.
14. Hook the belt over the left and right hand pulleys.
15. Repeat this procedure for any other belts that require repositioning.
Belt Position Dimension
2 42mm
3 84mm
4 126mm
5 168mm
6 210mm
7 252mm
8 294mm
9 336mm
10 378mm
11 420mm