Alltest-Agilent-Keysight-E9902G-Datasheet-29440-.pdf.pdf - 第17页

P a g e F i n d u s a t w w w . k e y s i g h t . c o m P a g e 16 Output Skew (same card) ± 5 ns typical, ±8 ns warranted Rise Time/Fall Time (no load) 15 ns (typical) Driver Voltage (no load) R ange 0 – 5.0 V Programmi…

100%1 / 22
P
a
g
e
Find us at www.keysight.com Page 15
Pin Cards and Test Access
Pin Cards for UnMux Systems
Maximum Number of Resources
1-Module
2-Module
4-Module
Pins / Nodes
1,296
2,592
5,184
Drive Channels
1,296
2,592
5,184
Receive Channels
1,296
2,592
5,184
Hybrid-144 pin Card*
9
18
36
Utility Card*
1
2
4
* Maximum number of cards per module = 9.
Hybrid-144 non-multiplex pin card
Parameter
Specification
Number of Pins/Card
144
Number of Channels/Card
144
Number of Drive Channels/Card
144
Number of Receive Channels/Card
144
Number of Grounds/Card
156
Multiplexing Ratio
1:1
Overdrive Capability
Yes
nanoVTEP Technology Capability
Yes
Hybrid-144 Non-multiplexed Pin Card Receivers
Parameter
Specification
Programmable Receive Delay Time
Minimum
0 ns
Maximum
Programmed vector cycle time
Resolution
2 ns (typical)
Accuracy (same card)
±8 ns typical, ±11 ns warranted
Input Voltage Range
0–4.875 V
Input Bias Current
+150 µA maximum
1
Parallel Capture RAM
128 bits
Response Compression
IEEE CRC-32 polynomial
2
Receiver Threshold Voltage
Range
0–4.875 V
Programming Resolution
20 mV (typical)
Static Accuracy
± 2% of setting ± 100 mV (typical)
Termination
Pull-Up Resistor
1000
Pull-Down Resistor
383
AC
150 pF, 68.1 in series
1. Varies with voltage.
2. Polynomial is 1 + x
2
+ x
4
+ x
5
+ x
7
+ x
8
+ x
10
+ x
11
+ x
12
+ x
16
+ x
22
+ x
23
+ x
26
+ x
32
Hybrid-144 Non-multiplexed Pin Card Drivers
Parameter
Specification
Frequency Range as a Clock
Minimum
625 kHz
Maximum
10 MHz
Programming Resolution
1
1% of frequency
Programmable Vector Cycle Time
Minimum
160 ns
Maximum
1.5 ms
Resolution
1
1% of vector cycle
Programming Resolution
1 ns
P
a
g
e
Find us at www.keysight.com Page 16
Output Skew (same card)
±5 ns typical, ±8 ns warranted
Rise Time/Fall Time (no load)
15 ns (typical)
Driver Voltage (no load)
Range
0–5.0 V
Programming Resolution
20 mV
Static Accuracy
± 2% of setting ± 20 mV
Output Backdrive Current
Peak
2
±750 mA
Continuous
±100 mA
DC Output Resistance
1.0 (typical)
Minimum Pulse Width Generation (TTL)
50 ns
High-Impedance State Leakage Current
3
−
150 µA
Programmable Device Test Time-out
Minimum
5.0 µs
Maximum
429 s
1. Add ±1 ns for periods over 100 ns.
2. Maximum width 2 ms, maximum duty cycle 10%.
3. Varies with voltage.
Parameter
Specification
Hybrid-144 Non-multiplexed Pin Card Drive/Receive Pins
Capacitance: Tri-State
130 pF
Capacitance: Disconnected
24 pF
Hybrid-144 Non-multiplexed Pin Card Relays
Maximum Voltage to Earth
±100 V peak
Maximum Current
750 mA
Maximum Switching Power
7.5 VA
Pin Cards for Mux Systems
Maximum Number of Resources
1-Module
2-Module
4-Module
Pins / Nodes
1,296
2,592
5,184
Drive Channels
1,296
2,592
5,184
Receive Channels
1,296
2,592
5,184
HybridPlus-DD Card*
9
18
36
AnalogPlus-DD Card*
8
16
32
AccessPlus Card*
8
16
32
Utility Card*
1
2
4
* Maximum number of cards per module = 9.
HybridPlus-DD Card
Parameter
Specification
Number of Pins/Card
144*
Number of Channels/Card (Split Driver-Receiver)
32
Number of Drive Channels/Card
16
Number of Receive Channels/Card
16
Multiplexing Ratio
2:9
Overdrive Capability
Yes
nanoVTEP Capability
Yes*
* Also applicable to AnalogPlus DD
HybridPlus-DD and AnalogPlus-DD Relays
Parameter
Specification
Maximum Voltage to Earth
±100 V peak
Maximum Current (constant)
500 mA
P
a
g
e
Find us at www.keysight.com Page 17
Maximum Current (pulsing)
700 mA
Maximum Switching Power
7.5 VA
HybridPlus-DD Card Receivers
Parameter
Specification
Programmable Receive Delay Time
Minimum
0 ns
Maximum
3.0 ms
Resolution
4 ns + 1% of vector cycle
Programming Resolution
1 ns
Maximum Input Voltage
12.0 V and
−
12.0 V
Parallel Capture RAM
128 bits
Pull-Up Curent Source
2.0 mA (typical)
Pull-Down Curent Source
5.0 mA (typical)
Receiver Threshold Voltage Range
Low Threshold
−
3.5 to 5.0 V
High Threshold
−
3.5 to 5.0 V
Programming Resolution
2.2 mV (typical)
Accuracy
±100 mV
Input Bias Current
±30 µA
Input Capacitance
83 pF
Disconnected Capacitance
12 to 23 pF (typical)
Bi-directional Capacitance
160 pF (typical)
HybridPlus-DD Card Drivers
Parameter
Specification
Frequency Range as a Clock
Minimum
625 kHz
Maximum
1
6.25, 12.5, or 20 MHz
Programming Resolution
2
1% of frequency
Programmable Vector Cycle Time
Minimum
1
160, 80, or 50 ns
Maximum
1.5 ms
Resolution
2
1% of vector cycle
Programming Resolution
1 ns
Peak Backdrive Current
−
3.5 to + 5.0 V source
750 mA
−
3.5 to + 5.0 V sink
−
500 mA
Continuous Output Current
Maximum Continuous Source Current
100 mA
Maximum Continuous Sink Current
100 mA
Slew Rate (into 100 ) Rising and Falling
Minimum
25 V/µs
Maximum
275 V/µs
Programming Resolution
25 V/µs
Driver Voltage
Range
3
−
3.5 to 5.0 V
Programming Resolution
2.206 mV
Static Accuracy (no load)
±100 mV
Minimum Pulse Width Generation (TTL)
50 ns
High-Impedance State Leakage Current
I
L
at V
O
= +3 V
25 to 150 µA
I
L
at V
O
=
−
2 V
−
150 to 0 µA
V
O
at I
L
= 0 A
−
0.7 to 0.7 V
Programmable Device Test Time-out
Minimum
5.0 µs
Maximum
429 s
Programming Resolution
100 ns
DC Output Resistance (at 500 mA)
1.15 to 2.0
Driver High-Impedance State Capacitance
125 pF (typical)
Disconnected Capacitance
12 to 23 pF (typical)