4OM-1064-001.pdf - 第248页
Tg0249-PM-MM 10. HDD/FDD OPERA TION Display 9910-001 3-202 10.2 SA VE/LOAD P A TTERN PROGRAM Display When the [P A TTERN PROGRAM] key is pressed at the “HDD/FDD OPERA TION” display , the following display appears on the …
9910-001 Tg0249-PM-MM
10. HDD/FDD OPERATION Display
3-201
Created Files
Shown below are the files and the addresses created in the four floppy disks.
Table 3.14
FD File Name Address Remarks
First Disk am1 xx.vzi a00000h to afffffh
x Anumber is
automatically
allocated to “xx” in
the file name.
Second Disk am2 xx.vzi b00000h to bfffffh
x A number is
automatically
allocated to “xx” in
the file name.
Third Disk am3 xx.vzi c00000h to cfffffh
x A number is
automatically
allocated to “xx” in
the file name.
Fourth Disk am4 xx.vzi d00000h to dfffffh
x A number is
automatically
allocated to “xx” in
the file name.
Tg0249-PM-MM
10. HDD/FDD OPERATION Display
9910-001 3-202
10.2 SAVE/LOAD PATTERN PROGRAM Display
When the [PATTERN PROGRAM] key is pressed at the “HDD/FDD
OPERATION” display, the following display appears on the screen.
Notes: (a) This display can be opened only when the machine is in the
“STOP” mode and no pattern program data or component library
data is exchanged between the machine and the programming
device (option).
(b) While this display is open, no pattern program data or compo-
nent library data can be exchanged between the machine and the
programming device.
The [ZERO] and [READY] buttons also become unavailable.
(c) Another display cannot be opened from this display during save
and load operation.
Save Operation (Machine
→→
→→
→
FD)
(1) Insert a DOS-formatted floppy disk (1.44 MB) into the FDD (floppy
disk drive).
(2) Move the line cursor (“MACHINE” side) to the pattern program data
to be saved.
Press the [SAVE ] key.
(3) “SAVING” appears in the “STATUS” text box, indicating that the
selected pattern program data is being saved.
• When the data is saved normally, “SAVED” appears in the text box
and the saved pattern program data name appears on the “FD” side.
• When an error is found during save operation, an error message is
issued and the save operation is interrupted.
Ref.: When the pattern program data having the same name is found
in the floppy disk, the display for confirmation to overwrite
appears on the screen.
Note: When a file in the floppy disk (a program file created on the
programming device side) keeps the data to be used exclu-
sively for another machine and is replaced with the new one,
it cannot be used for another machine.
To keep the exclusive data stored in memory, follow the data
replacement procedure through data communication with the
programming device.
Fig. 3.120
Tg0249-PM-MM
10. HDD/FDD OPERATION Display
0004-002 3-203
Load Operation (FD
→→
→→
→
Machine)
(1) Insert a floppy disk (a disk in which the nozzle stocker data is saved)
into the FDD (floppy disk drive).
(2) Press the [FD] key. The pattern program data names are displayed.
Note: Data other than the pattern program data is not displayed.
(3) Move the line cursor on the “FD” side to the pattern program data
name to be loaded and press the [LOAD ] key.
(4) “LOADING” appears in the “STATUS” text box, indicating that the
data is being loaded.
• When the data is loaded normally, “LOADED” appears in the text
box and the loaded pattern program data name appears on the ma-
chine side.
• When an error is found during load operation, an error message is
issued and the load operation is interrupted.
Ref.: When the pattern program data having the same name is
found in the floppy disk, the display for confirmation to
overwrite appears on the screen.
Notes: (a) When the loaded pattern progrma data contains some
component IDs which do not exist in the component li-
brary data on the machine side, it is required to load such
IDs from the programming device.
(b) Pattern Program Memory Capacity
The occupied capacity is determined according to the
interrelation of the below-described conditions.
Maximum Number of Steps: 5,000 steps/model
Maximum Memorized Number of Steps: 7,600 steps
Maximum Memorized Number of Models: 24 models
How to Delete the Pattem Program Data on “FD” Side
(1) Insert a floppy disk into FDD.
(2) Press the [FD] key. The pattern program data names are displayed.
(3) Move the line cursor (“FD” side) to the pattern program data name to
be deleted and press the [PRGM. DEL.] key.
The [DELETE] key appears at A in Fig. 3.121.
(4) When the [DELETE] key is pressed, the delete operation starts.
After the delete operation is completed, the pattern program names in
the floppy disk are displayed again.
• Data other than the pattern program data is not displayed.
• When an unformatted floppy disk is inserted into FDD and the
save operation is performed, an error message is issued.
A
Fig. 3.121