4OM-1064-001.pdf - 第26页

Fig. 1.18 Placement Head V acuum Filter Checking Remove the vacuum filter with the vacuum filter replacement jig (at- tached) and check for dirt. Replace the filter with a new one when it is stained excessively . Refer t…

1-15

Fig. 1.17 Vacuum Nozzle

0004-002 Tg0249-PM-MM

6. Monthly Maintenance

Inside of Vacuum Nozzle

Cleaning

Blow air to the inside of the vacuum

nozzle.

Hole of Vacuum Nozzle

Cleaning

Blow air to the hole of the vacuum

nozzle.

Vacuum Nozzle End

Cleaning

Clean it with a rag.

Fig. 1.16 Nozzle Stocker

Nozzle Storage Section

Cleaning

Remove dirt and dust using a rag.

Cam Follower

Cleaning and Lubrication (NM1)

(1) Wipe off old grease with an oiled

rag.

Note: Take care not to leave

any waste thread.

(2) Apply new grease with a brush,

etc.

Beam A Side

Beam B Side

Beam A Side

Beam B Side

Note: Sebum nor oil, etc., should not adhere to the surface of the diffusion plate.

Do not use a rag to wipe off dirt.

Refer to “1.7 Vacuum Nozzles of Section 2 in Volume 1” for details.

Diffusion

Plate

Note

Fig. 1.18 Placement Head

Vacuum Filter

Checking

Remove the vacuum filter with the

vacuum filter replacement jig (at-

tached) and check for dirt.

Replace the filter with a new one

when it is stained excessively.

Refer to “2.2 Replacement Procedure

of Vacuum Filter” for details.

Beam A Side

Beam B Side

6. Monthly Maintenance

9910-001 Tg0249-PM-MM

1-16

Table 1.7

7. Maintenance (Every 3 Months after Initial

Maintenance in 1 Month)

CAUTION

The ball screws and linear guides have a high mainte-

nance priority.

The initial maintenance should be performed in one

month. After that, it should be performed every three

months.

Notes: (a) Perform break-in after lubrication. After a proper break-in, wipe off

any dropped grease with an oiled rag.

(b) Grease Symbols

DE1 : DAPHNE EPONEX GREASE No.1

NM1 : NEW MOLYNOC GREASE No.1

7. Maintenance (Every 3 Months after Initial Maintenance in 1 Month)

0004-002 Tg0249-PM-MM1-17

Maintenance Spots Check

Name

Fig.

No.

Description Grease

Cleaning

Tools,

Nozzles, etc.

Feeder Base Cam and Cam Follower 1.19 Lubrication

NM1

Brush or

Cloth

X-Axis Ball Screw

(2 nipples)

1.20

-1

Cleaning and

Lubrication

DE1

Oiled rag,

Hand or Brush

X-Axis Linear Guide

(8 nipples)

1.20

-2

Cleaning and

Lubrication

DE1

Oiled rag,

H Type

Y-Axis Ball Screw 1.21 Cleaning and

Lubrication

DE1

Oiled rag,

Hand or Brush

X/Y Beam

(Beams A and B)

Y-Axis Linear Guide

(8 nipples)

1.21 Cleaning and

Lubrication

DE1

SPK-3C,

U and P

Types,

Oiled rag

Placement Head Ball Screw and Nut

(4 nipples)

Linear Guide

1.22 Cleaning and

Lubrication DE1

U and

N Types,

Oiled rag

Large Linear Guide

(2 nipples)

1.23 Cleaning and

Lubrication

DE1

Oiled rag, N

and U Types

Small Linear Guide 1.23 Cleaning and

Lubrication

DE1

Oiled rag,

Hand or Brush

Clamp Sections of

Tray Traverse

Cam Follower 1.23 Cleaning and

Lubrication

DE1

Oiled rag,

Hand or Brush