4OM-1064-001.pdf - 第28页

1-18 0004-002 Tg0249-PM-MM A Beam A Side Beam B Side A Fig. 1.19 Feeder Base Cam and Cam Follower Lubrication (NM1) (1) Remove the plate on the side of the feeder base as shown in the figure. (2 ) Apply new grease with a…

Table 1.7

7. Maintenance (Every 3 Months after Initial

Maintenance in 1 Month)

CAUTION

The ball screws and linear guides have a high mainte-

nance priority.

The initial maintenance should be performed in one

month. After that, it should be performed every three

months.

Notes: (a) Perform break-in after lubrication. After a proper break-in, wipe off

any dropped grease with an oiled rag.

(b) Grease Symbols

DE1 : DAPHNE EPONEX GREASE No.1

NM1 : NEW MOLYNOC GREASE No.1

7. Maintenance (Every 3 Months after Initial Maintenance in 1 Month)

0004-002 Tg0249-PM-MM1-17

Maintenance Spots Check

Name

Fig.

No.

Description Grease

Cleaning

Tools,

Nozzles, etc.

Feeder Base Cam and Cam Follower 1.19 Lubrication

NM1

Brush or

Cloth

X-Axis Ball Screw

(2 nipples)

1.20

-1

Cleaning and

Lubrication

DE1

Oiled rag,

Hand or Brush

X-Axis Linear Guide

(8 nipples)

1.20

-2

Cleaning and

Lubrication

DE1

Oiled rag,

H Type

Y-Axis Ball Screw 1.21 Cleaning and

Lubrication

DE1

Oiled rag,

Hand or Brush

X/Y Beam

(Beams A and B)

Y-Axis Linear Guide

(8 nipples)

1.21 Cleaning and

Lubrication

DE1

SPK-3C,

U and P

Types,

Oiled rag

Placement Head Ball Screw and Nut

(4 nipples)

Linear Guide

1.22 Cleaning and

Lubrication DE1

U and

N Types,

Oiled rag

Large Linear Guide

(2 nipples)

1.23 Cleaning and

Lubrication

DE1

Oiled rag, N

and U Types

Small Linear Guide 1.23 Cleaning and

Lubrication

DE1

Oiled rag,

Hand or Brush

Clamp Sections of

Tray Traverse

Cam Follower 1.23 Cleaning and

Lubrication

DE1

Oiled rag,

Hand or Brush

1-180004-002 Tg0249-PM-MM

Beam A Side

Beam B Side

Fig. 1.19 Feeder Base

Cam and Cam Follower

Lubrication (NM1)

(1) Remove the plate on the side of

the feeder base as shown in the

figure.

(2) Apply new grease with a brush, etc.

The cam and cam follower are lo-

cated in the depth of Arrow A.

Note: Lubricate it covering this

section with cloth, etc. to

avoid dropping grease

onto the wiring.

7. Maintenance (Every 3 Months after Initial Maintenance in 1 Month)

1-19

Fig. 1.20-1 X/Y Beam (Beams A and B) X-Axis

0004-002 Tg0249-PM-MM

X-Axis Ball Screw

Cleaning and Lubrication (DE1)

(1) Wipe off old grease with an oiled

rag.

Note: Take care not to leave

any waste thread.

(2) Lubricate the 2 nipples with new

grease from a grease gun.

Note: The attachments to be

used are SPK-3C, U type

and P type.

Fig. 1.20-2 X/Y Beam (Beams A and B) X-Axis

Beam A Side

Beam B Side

X-Axis Linear Guide

Cleaning and Lubrication (DE1)

(1) Wipe off old grease with an oiled

rag.

Note: Take care not to leave

any waste thread.

(2) Lubricate the 8 nipples with new

grease from a grease gun.

Note: The attachment to be

used is H type.

SPK-3C

U Type

P Type

Beam A Side

Beam B Side

Nipple

2 nipples

Nipple

H Type

7. Maintenance (Every 3 Months after Initial Maintenance in 1 Month)