Apollo1_Operators_Manuel.pdf - 第49页
49 cab - Produkttechnik GmbH / Tharo Systems, Inc. 9 Setup Using the setup mode, the configuration of the Apollo may be customized to suit specific requirements. Initial setup should be performed when operating the print…
48 cab - Produkttechnik GmbH / Tharo Systems, Inc.
ONL key Switch into OFFLINE mode.
FF key For scrolling down within the file list stored on the card.
Reduces the quantity of labels to be printed.
CAN key For scrolling up within the file list of the card.
Increases the quantity of labels to be printed.
PSE key Confirms file selection.
Moves the cursor to the right when setting the quantity of labels
to print.
Switch into PRINT mode.
System Mode LABEL FROM CARD
Provided that a memory card is installed and a label format is present, in OFFLINE
mode, press the key to enter the LABEL FROM CARD mode.
In this mode, the labels stored on the card can be selected to print; for files
with a variable number of labels the quantity of labels to be printed can be set.
Display
The top line of the display shows "Label from card". The bottom line of the
display shows the file name of the first label file in the list stored on the card.
After the requested label has been selected, for files without a fixed number of
labels the display shows "No. of labels" in the top line and "00001" in the
bottom line.
LED Display
All LED's off.
Function keys
Table 8 k Function keys in the LABEL FROM CARD mode
49cab - Produkttechnik GmbH / Tharo Systems, Inc.
9 Setup
Using the setup mode, the configuration of the Apollo may be customized to
suit specific requirements. Initial setup should be performed when operating
the printer for the first time. Changes which become necessary to process
different print jobs, e.g. when different materials are used, can mostly be
accomplished by changing the software settings.
Start of Setup Mode
This mode is initiated by either simultaneously pressing the key and the
key when switching on the printer and keep them pressed down until the
system test is completed, or in ONLINE mode, press the same two keys down
for at least 5 seconds.
Starting the setup mode, the display shows "SETUP" for about one second ,
followed by "Land" or "Country" which represents the first of the parameters to
select from. Depending on the selection, the setup parameters and their
settings will be shown. The list of parameters is brought up in a row and may
be run through repeatedly.
Each time a parameter setting has been changed, there will be a request for
confirmation. There will not be a general request before leaving the setup
mode.
The setup mode can be left at any point by pressing the key.
The confirmed parameters will be saved.
If an already confirmed setting is not desired any more, switch off the printer
during the setup mode to cancel changes.
To return to the original factory default settings, press all three keys, the
key, the key, and the key simultaneously and keep them pressed
down until the display shows "--- RESTORE ---".
Note, that in some cases the printer may initially be set to certain parameters
which may differ from the default settings. (e.g. "Country")
On the following pages, you will find details to change the setting of the
parameters.
F
50 cab - Produkttechnik GmbH / Tharo Systems, Inc.
1 Country (#)
2 Transfer print #
3 Label sensor #
4 Interface
5 Cut position #
6 Peel position #
7 Printhead position #
8 Heat level #
9 Printer info
10 Set date #
11 Set time #
12 Character set
13 Format card
14 Copy card
15 Backfeed (#)
16 Debug mode
17 Tear-off position #
18 Pause reprint
1 Country (#)
Starting Setup
Overview of the Setup Parameters
Fig. 9 a Setup parameters
Scrolling up/down the parameters :
Definition of the list items :
No
Para #
No ......... Item number
Para ...... Name of the parameter
# ............ Parameter may be altered via
software
(#) .......... Parameter is limited
changeable via software