Apollo1_Operators_Manuel.pdf - 第57页
57 cab - Produkttechnik GmbH / Tharo Systems, Inc. Peel Position Using the optional present sensor , the "Peel position" parameter allows you to alter the position of the dispensed label relative to the dispens…
56 cab - Produkttechnik GmbH / Tharo Systems, Inc.
Cut Position
Using the optional cutter, the "Cut position" parameter allows you to alter the distance
between the cutting edge and the rear edge of the label. Normally, with the initial
offset value of "0" the cutting edge is in the middle of the gap between two labels.
Adjustments have to be carried out only once after a cutter has been installed.
(range from -.33 to +.33 in or -8.4mm to +8.4mm) If the cut position value is
positive, the media will be advanced before it is cut, that means there is a greater
distance between the cutting edge and the rear edge of the label.
It is recommended that you carry out changes for single print jobs in the software.
(e.g. if the cut is not wanted in the middle of the gap)
The software provides a second value for individual adjustments.
You may also change this value using the software commands. Any front panel value
and software command value are totaled together for printing.
The current field to be changed is flashing in the display.
4 Interface
6 Peel Position
5 Cut Position
Cut Position
+ x.x mm
Cut Position
- x.x mm
Cut Position
± 9.x mm
Cut Position
± 0.x mm
Cut Position
± x.9 mm
Cut Position
± x.0 mm
*
*
*
*
*
*
Cut Position
± x.x mm Yes
Cut Position
± x.x mm No
Confirmation
Sign (+ or -)
1/10 mm
mm
Fig. 9 f Set "Cut Position" parameter
F
57cab - Produkttechnik GmbH / Tharo Systems, Inc.
Peel Position
Using the optional present sensor, the "Peel position" parameter allows you to alter
the position of the dispensed label relative to the dispense edge.
Normally, with the initial offset value of "0" the label is removed from the carrier
ribbon until only a .08 in or 2 mm wide part of the label still sticks on the ribbon.
Adjustments have to be carried out only once when a present sensor is being
installed. (range from -.33 to +.33 in or -8.4 mm to +8.4 mm)
If the peel position value is positive, the label will be removed further leaving a
smaller strip sticking on the carrier ribbon.
It is recommended that you alter the parameter for single print jobs via software
(e.g. if an applicator is used and, therefore, the labels have to be removed
completely). The software provides a second value for individual adjustments.
You may also change this value using the software commands. Any front panel
value and software command value are totaled together for printing.
The current field to be changed is flashing in the display.
5 Cut Position
7 Printhead pos.
6 Peel Position
Peel Position
+ x.x mm
Peel Position
- x.x mm
Peel Position
± 9.x mm
Peel Position
± 0.x mm
Peel Position
± x.9 mm
Peel Position
± x.0 mm
*
*
*
*
*
*
Peel Position
± x.x mm Yes
Peel Position
± x.x mm No
Confirmation
Sign (+ or -)
1/10 mm
mm
Fig. 9 g Set "Peel Position" parameter
F
58 cab - Produkttechnik GmbH / Tharo Systems, Inc.
Printhead Position
The "Printhead position" parameter defines the location of the print image on
the label.
The parameter should especially be altered if you are using the same label
formats on several printers, and you find the print image located differently on
the labels when they were printed on another printer. (range from -.33 to +.33
in or -8.4 mm to +8.4 mm)
If the printhead position value is positive, the print image is shifted further to
the rear edge of the label.
Adjustments for various print jobs may also be carried out via software which
provides an additional offset value.
You may also change this value using the software commands. Any front panel
value and software command value are totaled together for printing.
The current field to be changed is flashing.
6 Peel position
8 Heat level
7 Printhead pos.
Printhead pos.
+ x.x mm
Printhead pos.
- x.x mm
Printhead pos.
± 9.x mm
Printhead pos.
± 0.x mm
Printhead pos.
± x.9 mm
Printhead pos.
± x.0 mm
*
*
*
*
*
*
Printhead pos.
± x.x mm Yes
Printhead pos.
± x.x mm No
Confirmation
Sign (+ or -)
1/10 mm
mm
Fig. 9 h Set "Printhead position" parameter
F