00194313-03.pdf - 第55页
SIPLACE S-25 HM / S-27 HM 2 Assembly Inst ructions for PCB Camera, Multicolor 02/2007 Edition 2.3 Safety Instructions 55 Rules for Germany: Observe the gu idelines of the Main Assoc iatio n of the German T rade Associati…
2 Assembly Instructions for PCB Camera, Multicolor SIPLACE S-25 HM / S-27 HM
2.3 Safety Instructions 02/2007 Edition
54
2.3.1 Safety Notes about Laser Radiation
DANGER from laser radiation
2
Do NOT change or manipulate the safety equipment or the PCB camera Multicolor itself. The
LED illumination device for the PCB camera Multicolor complies with laser class "1M" without
any protective measures.
With protective measures, i.e., installing it in the machine properly, the PCB camera Multicolor
complies with laser class "1".
With this laser class, no laser warning signs are required on the machine (on the safety hoods) or
on the camera itself.
It is sufficient if the signs identifying the laser class and "1" and "1 M" are in the User Manual, as
shown below.
Abb. 2.3.1 Laser Warning Signs in the User Manual in the Pertinent National Language
Classifying the PCB camera Multicolor as laser class "1M" or "1" only applies if no one manipula-
ted with the camera. Make certain that the lacquer on the setting potentiometer on the camera
and on the "PCB camera board modular" is undamaged.
Otherwise there will be a higher risk of an accident due to LED radiation and it is not allowed to
install/continue to operate the PCB camera Multicolor in its current condition.
Cameras with a damaged seal must be returned to Siemens. 2
The voltage for the LED illumination of the PCB camera Multicolor is integrated into the safety
circuit. It is switched off automatically when a protective cover is opened, emergency off is trigge-
red or the component changeover table on the machine frame is unplugged (interface cable).
With "Key-operating switch in service position" the protective function (= shut-off of the LED
camera illumination) is retained. During the assembly the final safety check has to be carried out,
as described in Abschn. 2.11.
SIPLACE S-25 HM / S-27 HM 2 Assembly Instructions for PCB Camera, Multicolor
02/2007 Edition 2.3 Safety Instructions
55
Rules for Germany:
Observe the guidelines of the Main Association of the German Trade Association, VBG 93.
In all other countries, comply with the pertinent guidelines and standards of the specific countries
in question.
Standards to be observed:
IEC 60825-1, EN 60825-1.
2
2.3.2 Definitions
DANGER
in terms of these instructions means that death, severe bodily injury or considerable material da-
mage WILL occur if the instructions about danger are not followed.
2
WARNING
in terms of these instructions means that death, severe bodily injury or considerable material da-
mage may occur if the warnings are not heeded. 2
CAUTION
in terms of these instructions mean that minor bodily injury or material may occur if the cautions
are not heeded. 2
NOTE
in terms of these instructions is a statement of important information about the product or the
pertinent portion of the instructions to which particular attention is being drawn. 2
2 Assembly Instructions for PCB Camera, Multicolor SIPLACE S-25 HM / S-27 HM
2.4 Assembly Kits, Tools 02/2007 Edition
56
2.4 Assembly Kits, Tools
2.4.1 Assembly Kit "PCB Camera Multicolor S-25 HM / S-27 HM"
2
2.4.2 Tools, Auxiliary Test Equipment and Expendable Materials
– Drill, possibly cable drum
(only for S.25 HM with a manufacturing date Sep to Dec 98)
– Drill bits for core diameter 3.3 mm and thread cutter M4
(only for S.25 HM, with a manufacturing date Sep to Dec 98)
– Vacuum cleaner (only for S.25 HM, with a manufacturing date Sep to Dec 98)
– Set of Allen wrenches
– Oblique-nosed cutting pliers
– Open-end wrench or size 6 mm socket wrench (only for HS-50)
– Wire stripper
– ESD bracelet
– Crimping pliers made by AMP (for connector sleeves)
– Insulating tape and permanent marker
– Ethyl alcohol.
1 Assembly Kit "PCB Camera Multicolor S-25 HM / S-27 HM" Item no. 00358042-01
2
PCB Camera Multicolor assembly, made by Sticksel LP-Kamera
Multicolor, Fa. Sticksel each with 2 connection cables
Item no. 00355462-01
2
Spacer plate (= adapter) Item no. 00348078-01
6
hex head cap screw M3 x 14 (captive) Item no. 00327105-01
2
PCB camera board, modular, made by Sticksel Item no. 00344490-01
1
Assembly kit 50 V module for PCB camera S-25 HM / S-27 HM,
consisting of:
Item no. 00357863-01
1 Relay RS 30 / 24 VDC GSE 1 A,
manufacturer: Weidmüller: Order no. 11 01 66
Item no. 00345646-01
1 Converter 24V/50V 50 mA, Siemens AG (universal illumination
converter)
Item no. 00349095-01
1 Retrofit cable for voltage module, 50 V, consisting of: Item no. 00356979-01
Cable W1 with 2 connector sleeves and 1 twin connector sleeve
Cable W2, complete, with 1 connector sleeve *)
Cable W3, complete, with 1 connector sleeve *)
Cable W4, complete, with connector sleeves
Cable W 5, complete, with 2 connector sleeves
7 Twin connector sleeves 2 x 1.5 mm
2
, Order no. 18H 7081,
Bürklin (1unit = reserve)
Order no. 18H 7081