Maintenance Manual.pdf - 第183页

AV131 MAINTENANCE MANUAL 8.2 I nserti on Head Un i t D79MEC-W 1-M 00-A0 8.2- 4 8.2. 3 Rotary Chuck and Centering C huck Replacement Unit No. N610052073A A 8.2 .3 R ot ar y Ch uck and C ent e r in g Chuc k R epl ac emen t…

100%1 / 244
AV131
MAINTENANCE MANUAL
8.2 Insertion Head Unit
D79MEC-W1-M00-A0
8.2-3
8.2.2 Insertion Guide Height Adjustment
Unit No. N610052012AA / 1087110000 / N610052020AA
8.2.2 Insertion Guide Height
Adjustment
=PREPARATION=
1. PCB 1.6 mm thick
Insertion Guide Height Adjustment
9.
1. Turn the power ON and return to origin.
2. Check that the X-Y table rail is not located below the
insertion head.
If located, move the X-Y table rail to a position where it
will not interfere with the head even when the head is
lowered.
3. Open the front cover.
4. Turn the maintenance switch ON.
5. Press “START” on the main control panel.
Make sure the red lamp of the signal tower flashes.
6. Turn the “SERVO” switch OFF.
7. Turn the “HEAD BRAKE” switch OFF (RELEASE).
8. Rotate the handwheel to set the cycle timer to 233°.
9. Turn the “HEAD BRAKE” switch ON (LOCK).
10. Combine thickness gauges properly and check that the gap
between the head and anvil is within the range of PCB
thickness + 0.25.
=REMARKS=
Check the clearance at two consecutive cycles because
a 2-cycle cam is incorporated.
11. If there is some clearance or if the PCB is being pressed down, loosen the nut bolt and rotate the slide
block to adjust the insertion guide height. (Insert an Allen wrench in the hole of the slide block and rotate it
to make adjustment.)
12. When adjustment is completed, tighten the nut bolt.
Nut
Slide block
Holes for rotating
slide block
(PCB thickness +0.25)
±
0.05
AV131
MAINTENANCE MANUAL
8.2 Insertion Head Unit
D79MEC-W1-M00-A0
8.2-4
8.2.3 Rotary Chuck and Centering Chuck Replacement
Unit No. N610052073AA
8.2.3 Rotary Chuck and Centering
Chuck Replacement
Rotary Chuck Replacement
10.
1. Turn the power OFF.
2. Move the chuck unit toward you.
3. Remove the E-ring and pull the pins out.
4. Pull the chuck out.
=REMARKS=
Be careful not to drop the spring at this step.
5. Replace the chuck.
6. Put the spring inside of the hole of the chuck.
7. Apply thin coat of grease to the sliding part that
fits in the chuck body.
8. Close the chuck with hands and check whether
the chuck is opened by the force of the spring.
9. Insert the chucks.
10. Insert the pin and fix with the E-ring.
Centering Chuck Replacement
11.
1. Turn the power OFF.
2. Move the chuck unit toward you.
3. Loosen the bolts and remove the centering
chuck.
4. Replace the centering chuck.
5. Tighten the bolts.
Collar
Chuck (L)
Chuck (R)
Cylinder block
Spring
Pin
Roller
Pin
Pin
E-ring
Roller
Centering chuck
Bolt
AV131
MAINTENANCE MANUAL
8.3 Part Supply Unit
D79MEC-W5-000-A0
8.3-1
8.3. Part Supply Unit
D79MEC-W5-000-A0
8.3.1 Component Detection Sensor Adjustment
Unit No. N610052014AA
8.3.1 Component Detection Sensor
Adjustment
Component Detection Sensor Adjustment
MODE switch Jog switch
Turn
Press Press
‘+’ side ‘-’ side
12.
1. Press the <MODE> switch to change the mode to ‘L/D’. Check that ‘D-ON’ appears on the digital display.
(If not, turn the jog switch until ‘D-ON’ is displayed.)
2. Press the <MODE> switch to change the mode to ‘TEACH’.
3. With a work present (blocking the component detector), press the jog switch for more than 0.5 seconds.
=REMARKS=
Use a metal scale, etc., as a work for adjustment to block the light completely.
4. When “AUTO” appears on the digital display, release the jog switch.
5. The judgment on the stability of sensing is displayed.
(If stable sensing is enabled, “GOOD” is displayed and “HARD” appears if not.)
=REMARKS=
When a component is within the sensing range, the stability indicator will turn ON.
13.
Operation indicator
(Orange)
Stability indicator (Green)
MODE indicator / L/D ON (Yellow)
MODE indicator / TIMER (Yellow)
MODE indicator / RUN (Green)
MODE indicator / TEACH (Yellow)
MODE indicator / ADJ (Yellow)
MODE indicator / PRO
(Yellow)
Digital display
Jog switch
MODE switch