KE2010.Instruction Manual.Ver.2.01,Rev.08.pdf - 第1119页

36 Error M essages on Saf ety Error code Message E691001 Input/Output buffer status of CCL-48M does not get ready E691002 W riting-in buffer of flush memory does not get useable E691003 Deleting cue of flush memory does …

Error Messages on CVS

Error code Message

E690001 CVS is not installed

E690002 Impossible to switch to Resistance Measurement mode since the probe has not shut down.

Please shut the probe down then try again

E690003 Impossible to switch to Condenser Measurement mode since the probe has not shut down.

Please shut the probe down then try again

E690004 The measurement mode is not correct

E690005 Parameter to control probe is not correct

E690006 Probe has to be shut down to measure resistance. Please shut probe then try again

E690007 Probe has to be shut down to measure condenser. Please shut probe then try again

E690008 Diode measurement is not available unless probe shuts down. | Please shut probe then try

again

E690009 The measurement is impossible since measurement mode is not set to Resistance

measurement. Please switch to the Resistance measurement mode then try again

E690010 The measurement is impossible since measurement mode is not set to Condenser

measurement.

Please switch to the Condenser measurement mode then try again

E690011 The measurement is impossible since measurement mode is not set to Diode

measurement. Please switch to the Diode measurement mode then try again

E690012 The measurement is impossible since the gotten measurement mode is set to Resistance

measurement

E690013 The measurement is impossible since the gotten measurement mode is set to Condenser

measurement

E690014 The measurement is impossible since the gotten measurement mode is set to Diode

measurement

E690015 The resistance when zero-adjusting is abnormal. Please check if probe short-circuits or not

E690016 A time-out occurred while reading resistance in

E690017 A time-out occurred while reading volume in

E690018 A time-out occurred while reading voltage in

E690019 The measured resistance does not get stable. Please check the probe status

E690020 The measured volume does not get stable. Please check the probe status

E690021 The measured voltage does not get stable.

Please check the probe status”

E690022 Something is wrong with the measured resistance

E690023 Something is wrong with the measured volume

E690024 Something is wrong with the measured voltage”

E690025 Something is wrong with the measured resistance(unit)

E690026 Something is wrong with the measured volume(unit)

E690027 Something is wrong with the measured voltage(unit)”

E690028 Resistance can no be measured. Please check if probe shuts down properly

E690029 Volume can not be measured. Please check if probe shuts down properly

E690030 Voltage can not be measured. Please check if probe shuts down properly

Error Messages on Safety

Error code Message

E691001 Input/Output buffer status of CCL-48M does not get ready

E691002 Writing-in buffer of flush memory does not get useable

E691003 Deleting cue of flush memory does not get useable

E691004 WSM(Write State Machine) of flush memory does not get ready

E691005 Write-in voltage range error occurred in flush memory control

E691006 Write-in error occurred in flush memory control

E691007 Write-in error occurred in flush memory control

E691008 Command sequence error occurred in flush memory control

E691009 Lock Bit Set error occurred n flush memory control

E691010 Lock Bit Clear error occurred in flush memory control

E691011 The check word for the common data of flush memory is abnormal

E691012 The checksum for the common data of flush memory is abnormal

E691013 The data version for the common data of flush memory is abnormal

E691014 The data length for the common data of flush memory is abnormal

E691015 The data kind for the common data is abnormal

Error Messages on Self-calibration

Error code Message

E906001 Memory allocation error

E906002 Shared memory open error

E906011 The measured value exceeds the limit. Check the MS parameters set.

E906021 The machine has not zeroed yet.

E906022 The machine is in the servo free state.

E906031 The selected device is not installed on the machine. Re-select another device.

E906041 There is no available head.

E906042 There is no available VCS.

E906043

%s is disable. Selected unit can not measure

E906051 The No. 501 nozzle and 502 nozzles are not assigned to the ATC. Assign the nozzles to

the ATC on the ATC nozzle setup menu which is invoked from the Machine Setup menu.

E906052 The No. 508 nozzle and 507 nozzles are not assigned to the ATC. Assign the nozzles to

the ATC on the ATC nozzle setup menu which is invoked from the Machine Setup menu.

E906061 The machine could not recognize a mark of the calibration jig used for laser alignment.

Check the jig position.

E906062 The machine could not recognize a mark of the calibration jig used for laser alignment.

E906071 The machine could not pick up the calibration jig used for laser alignment. Check to see if

the jig is placed on the calibration block.

E906072 The machine could not pick up the calibration jig used for laser alignment. Check to see if

the jig is placed on the jig station.

E906073 The offset from the jig placement position to the calibration block position exceeds the limit.

Check the MS parameter.

E906074 The position of the calibration jig for used for laser alignment is abnormal. Check the jig

position.

E906075

Calibration jig for VCS has not been picked up. Check that jig is placed on jig station

E906101 An error occurred when the machine detected the height of the laser measurement surface.

E906102 An error occurred during setting of the laser parameter.

E906103 An error occurred during laser measurement (ONCE).

E906104 An error occurred during laser measurement (SWEEP).

E906105 An error occurred when the machine checked to see if there was a component.

E906201 An error occurred at the axis.

E906301

Error has occurred on axis code:%ld

Q907001 Will you set the safe direction of each I/O device ?

Q907002 The machine will terminate self-calibration. Save the settings?

Q907011 The machine has not zeroed yet. Zero the machine?

Q907021 A component cannot be returned. Discard the component?

I908001 Remove a component at ?.

I909001 The No. ? nozzle will be removed.

I909002 The ? will be returned to the jig station.