KE2010.Instruction Manual.Ver.2.01,Rev.08.pdf - 第1168页

85 E500605 “An error occurred when disposing a component ” [Cause] T his er ror occ urs if the com ponent pres ent check at a com ponent dis posal action gets an error when starting a production. [Treatm ent] Pressing O …

E500303 “Detected %s feeder float”

[Cause] A matter that may interrupt the Feeder floatation sensor occurred.

? : where the matter occurred.

On the front side

On the rear side

On both sides

[Treatment] Please remove the obstruction that may be interrupting the sensor.

E500401 “Input order Simple Opt. Error <%s>”

[Cause] An error occurred while optimizing the pick positions by input orders.

? : the details of the error

There is no component corresponding to the feeder.

The head can not travel to the feeder/MTC position.

The head can not travel to the holder/MTS position.

There is no head available to place the component.

There is no head that meets the centering type.

An internal error of the Input order Simple Opt. Error process.

Treatment] 1 and 6 are a program error. Please make a note of the cause of the error and

the error code, then contact our technical service Dept. for information.

In case of 2, 3, and 4, please go to the Production Program Editor and see the

specified head(s) in the Placement data.

In case of 5, please go to the Production Program Editor and see the centering

type in the Component data.

E500500 “Teaching can not be executed”

[Cause] You are trying to teach unexecutable data to the machine.

Unexecutable data:

Data except ref. circuit in the Placement position teaching.

Components except tray component in the Pick position teaching.

When multiple heads are working at the same time.

[Treatment] You can not perform a teaching with the current status. Please go on the process.

E500501 “The selected device can not be used”

[Cause] You selected a device not available.

[Treatment] Please change devices to use.

E500502 “With the selected device, it is impossible to move to the aimed

position”

[Cause] You can not move to the specified position with the selected device.

[Treatment] Please select another device.

E500503 “Standard Pin position illegal. Correct coordinates can not acquire”

[Cause] The position of the reference pin is not correct.

[Treatment] In the Setup, please teach the positions of the reference pin and follower pin to

the machine.

E500605 “An error occurred when disposing a component”

[Cause] This error occurs if the component present check at a component disposal action

gets an error when starting a production.

[Treatment] Pressing OK button will abort the process. In this case, the production will not be

executed.

E500700 “An error occurred while Auto. PWB Width Alignment Control. The

process gets discontinued”

[Cause] This error occurs if an error occurs or an action did not take place properly while

Auto. PWB Width Alignment Control.

[Treatment] Pressing OK button will abort the process. If a particular reason (Home returning

has not been complete, etc.) why Auto. PWB Width Alignment Control can not be

executed is given, please perform any means to get rid of the factor that stops

Auto. PWB Width Alignment Control. If any particular reasons are not given,

please, check the action of Auto. PWB Width Alignment Control by Manual

control .

E500701 “Para error. PWB Width Alignment Control occurred”

[Cause] This error occurred if an entered value to be defined by Enter key is wrong when

performing Auto. PWB Width Alignment Control.

[Treatment] Please check the entered value.

E500800 “A PWB is detected within the conveyors of both stations. Please

remove the PWB”

[Cause] The production can not get started because PWBs are on the conveyors on both

sides when starting the production.

[Treatment] Please remove the PWBs from the conveyors by pressing OK button, and then

press START key again.

E500801 “A PWB is detected within the conveyor of the Left station. Please

remove the PWB”

[Cause] The production can not get started because a PWB is on the conveyor on left

side when starting the production.

[Treatment] Please remove the PWBs from the conveyors by pressing OK button, and then

press START key again.

E500802 “A PWB is detected within the conveyor of the Right station. Please

remove the PWB”

[Cause] The production can not get started because a PWB is on the conveyor on right

side when starting the production.

[Treatment] Please remove the PWBs from the conveyors by pressing OK button, and then

press START key again.

E501999 “Abnormal stop <%s>

[Cause] This error occurs when an action does not end normally.

? : An action that was taking place when a production ended abnormally.

While transporting PWBs

While recognizing VCS

While recognizing

IC marks

While recognizing BOC marks

While detecting bad marks

Placement position

Pick position

While recognizing L3

While installing a nozzle on a head

While returning a nozzle to ATC

While disposing a component

While reading bank marks

Other positions

[Treatment] A detailed error message should have been shown prior to this message.

Please check and see the status, using the given error number.

E500900 “The connection with HLC is on-line. The production is not available

with the currently selected production program created by the

machine”

[Cause] The connection between your machine and HLC is set to ON in the Setup. The

currently selected production program was created by the machine. Therefore, its

production can not get started.

[Treatment] Please cut off the connection between your machine and HLC in the Setup or

read in another production program.

E500901 “It is not connected to HLC. The production is not available with the

currently selected production program created by HLC”

[Cause] A production program that was created by HLC was read in and its production is

about to get started with the connection between your machine and HLC being

OFF.

[Treatment] Please enable the connection between your machine and HLC in the Setup or

read in another production program.

E500902 “Online switch is not effective to the Setup data though the

connection with HLC is turning on”

[Cause] Online switch is not available while the connection between your machine and

HLC is ON in the Setup data.

[Treatment] Please cut off the connection between your machine and HLC in the Setup or

enable the online switch.

E501000 “MTC Move Failed”

[Cause] This error occurs when an error occurs from MTC during a production.

[Treatment] Please turn off the power supply of MTC and examine it.