ELA Generic Tooling.pdf - 第11页

MACHI NE PROG RAMMI NG STAGE 5B - VACUU M TOOLIN G User Manual 1.25 to the vacuum box inlet , ensure the hose is rout ed clear of any par ts. 19. L ower the printhead shutter . 20. Pr ess the System button. 21. Sel ect B…

100%1 / 47
MACHINE PROGRAMMING
STAGE 5B - VACUUM TOOLING
1.24 User Manual
10. Select Adjust (F1).
11. Use the Next and Previous keys (F4 - F5) to highlight each parameter.
12. Use the Incr. and Decr. keys (F6 - F7), or the forward slash key (/) on the
keyboard, to change the parameter value.
13. Select Save (F2). The message ‘Saving fiducial data - Please wait Board
data file saved’ is displayed.
14. Select Exit (F8).
15. Select Full Width (F5). The message ‘Checking for a board on the belts’
is displayed. Whilst the rear rail is moving the message ‘Rail Moving...’ is
displayed.
16. Select Open Cover (F2).
17. Raise the printhead shutter.
18. The vacuum box can now be fitted into the appropriate location holes in the
tooling plate. Ensure the vacuum box is placed into the correct set of holes
taking regard of the type of stencil being used. Connect the vacuum hose
Adjust
Open
Cover
Home
Cleaner
Board
Stop
Full
Width
Load
Width
Generic
Tooling
Exit
Save Next Previous Incr. Decr. Exit
Save Next Previous Incr. Decr. Exit
Save Next Previous Incr. Decr. Exit
Save Next Previous Incr. Decr. Exit
Adjust
Open
Cover
Home
Cleaner
Board
Stop
Full
Width
Load
Width
Generic
Tooling
Exit
Adjust
Open
Cover
Home
Cleaner
Board
Stop
Board
Width
Load
Width
Generic
Tooling
Exit
MACHINE PROGRAMMING
STAGE 5B - VACUUM TOOLING
User Manual 1.25
to the vacuum box inlet, ensure the hose is routed clear of any parts.
19. Lower the printhead shutter.
20. Press the System button.
21. Select Board Width (F5). The message ‘Checking for a board on the
belts’ is displayed. Whilst the rear rail is moving the message ‘Rail
Moving...’ is displayed.
22. Select Generic Tooling (F7). The print carriage moves to the front of the
machine.
The following window and menu bar is displayed:
NOTE
If contaminated squeegees are fitted, these should be replaced at this point.
23. Select Continue (F1). Cleaner moves to the Home position and the print
carriage moves to the rear of the machine. The message ‘Table at Home
Height’ is displayed.
Adjust
Open
Cover
Home
Cleaner
Board
Stop
Board
Width
Load
Width
Generic
Tooling
Exit
Adjust
Open
Cover
Home
Cleaner
Board
Stop
Full
Width
Load
Width
Generic
Tooling
Exit
Generic Tooling Warning
WARNING Paste may drip into the machine
Remove Squeegees NOW
Continue
Open
Cover
Exit
Continue
Open
Cover
Exit
MACHINE PROGRAMMING
STAGE 5B - VACUUM TOOLING
1.26 User Manual
24. Select Transprt Height (F3). The message ‘Table at Transport Height’ is
displayed.
25. Place a board on the input sensor of the upline conveyor of the machine.
26. Select Load (F1).
27. Select Auto Board (F1).
28. Select Vision Height (F3). The message ‘Table at Vision Height. Check
Tooling Clearance’ is displayed.
29. Select Contact Height (F3).
The following window and menu bar is displayed:
30. Select Continue (F1). The message ‘Table at Contact Height. Check
Tooling Clearance’ is displayed.
31. Select Open Cover (F7).
32. Raise the printhead shutter.
Load
Transprt
Height
Board
Clamps
Change
Screen
Open
Cover
Exit
Load
Vision
Height
Home
Height
Board
Clamps
Change
Screen
Open
Cover
Exit
Auto
Board
Manual
Board
Exit
Unload
Vision
Height
Home
Height
Board
Clamps
Change
Screen
Open
Cover
Exit
Contact
Height
Transpr t
Height
Change
Screen
Open
Cover
Exit
Contact Height Warning
WARNING Check for obstructions between
the Rails and the Screen
Continue
Open
Cover
Exit
Continue
Open
Cover
Exit
Vision
Height
Open
Cover
Exit