00198501-02_IM_711.1_R18-1_EN.pdf - 第13页

Station Software V ersion 711.1 (R 18 - 1) / Installat ion Manual 05/2018 Edition 13 4.1.3 Embedded Software 4.1.3.1 Composi tion of the File Name 1..6 7 8 9 10 11 12 13 14 15 16 17 18 19 Sub - system name Sepa - rator V…

100%1 / 76
Station Software Version 711.1 (R18-1) / Installation Manual 05/2018 Edition
12
4 Requirements
4.1 Software Components of SIPLACE Series X, X S, SX, DX, CA and
TX
4.1.1 Station
– Microsoft .NET 4.6.1 (must be installed manually)
– The station only uses one of the following operating system configurations on the station
computer and Coplan computer/feeder computer:
– Microsoft Windows Embedded Standard 7 (WES7, 32-bit or 64-bit)
The station computer has to be equipped with at least 2 GB memory (RAM) with WES 7, 32-bit
and 4 GB memory (RAM) with WES7, 64-bit respectively. If necessary, station computers in the
field have to be exchanged or upgraded with a memory extension. Please refer to the
Technical Information TI2014-09E04.
4.1.2 Machine Components
The following versions of other machine components are required for the station software to
function correctly:
SIPLACE station software SIPLACE Vision SIPLACE Pro
Version 711.1
*)
Version 552 Version 15.1
**)
*)
in compatible mode: Version 710.3©
**)
in compatible mode: SIPLACE Pro 14.x
CAUTION
The functional statuses of the station computer, Vision computer and SIPLACE Pro
software must be compatible, as specified above. Another configuration is not supported.
Station Software Version 711.1 (R18-1) / Installation Manual 05/2018 Edition
13
4.1.3 Embedded Software
4.1.3.1 Composition of the File Name
1..6 7 8 9 10 11 12 13 14 15 16 17 18 19
Sub-
system
name
Sepa-
rator
Variant ID Hard-
ware ID
1)
Target
2)
Version Release . File type
Please
refer to
table in
section
4.1.3.2
_ 0 = no
variant
00
0 = BIOS 00
H
00
H
. HEX
_ A =
Variant
(SOKO)
…
… … … . JED
_ ... 99 9 = App 9 FF
H
FF
H
. BHX
Table 4-1: Composition of the file name
1)
Change compared with old file name (from one to 2 digits)
2)
Extended to second CAN
Station Software Version 711.1 (R18-1) / Installation Manual 05/2018 Edition
14
4.1.3.2 Comparison of Old and New Names of the Subsystems
Old subsystem name
(<7xx)
New subsystem name
(7xx)
Name
A AXIALL General axes (including free axis),
excluding DP axes of the C&P20A head
B COMTAB Component table
C VHSAXS Star axis of C&P20A head
E IOMODU CAN I/O module
F (Replaced by AXIALL) Free axis
G TAPCUT Tape cutter
H VHSHED C&P20A head
I TWIHED Twin Head
J VHSAXD DP axis of C&P20A head
L TWIAPR / VHSAPR Pressure regulation valve
(Twin Head / C&P20 head)
M MTCHNG MTC
N ---
O ---
P TWIAXZ Z-axis, Twin Head
Q ---
R TWIAXD DP axis, Twin Head
T CONVEY PCB conveyor
U FEEDER Feeder
V ILLUMI Vision
W VHSAXZ Z-axis, C&P20A head
X GANAXX X-axis
Y GANAXY Y-axis
--- CCPAPR
1)
Pressure regulation valve, CPP head
--- CPPAVA
1)
Valve cluster, CPP head
--- CPPAXD
1)
DP axis, CPP head
--- CPPHED
1)
CPP head
--- CPPSCO
1)
Component sensor