00196430-0102-AI_Head_Reconfiguration_Kit_SX_CPP_en_de.pdf - 第69页

Installing the CPP Placement Head Height Adjustment and Installatio n of the Nozzle Station Assembl y of the CPP Placement Head Assembly Instructions / Montageanleitung Head Reconfiguration K it CPP 69 Installing the Noz…

Installing the CPP Placement Head

Assembly of the CPP Placement Head Height Adjustment and Installation of the Nozzle Station

68 Assembly Instructions / Montageanleitung Head Reconfiguration Kit CPP

3.4.7 Height Adjustment and Installation of the Nozzle Station

The nozzle station [03073328-xx] is included in the parts set.

When replacing a C&P20A head by a CPP head and vice versa the present nozzle station can be kept.

When replacing a TwinHead by a CPP or a C&P20A head the nozzle station of the parts set must be

installed.

Height Adjustment of the No zzle Station

3.4.7.1 Height Adjustment of the Nozzle Station

CAUTION

► If the COT insert has been removed or shifted during the conversion, the installation height

of the nozzle station should be checked in any case.

Measuring the height of the nozzle station

► Push the placement head to be measured outwards.

► Place the caliper perpendicularly on the contact sur

face of the reject station (1) and measure the dis

tance to the guide rail of the gantry.

This distance must be 189mm ± 0.2mm (2).

► If the distance is correct, proceed with the installation

of the nozzle station.

Position for the shim plates

► If the distance is too large, insert shim plates: Shim

plates for nozzle stripping device [03039514

xx and

03021079-xx], screws DIN7991 M4x20 - 8.8

[00333782

xx].

► If the distance is too small because shim plates have

already been inserted, remove these.

Installing the CPP Placement Head

Height Adjustment and Installation of the Nozzle Station Assembly of the CPP Placement Head

Assembly Instructions / Montageanleitung Head Reconfiguration Kit CPP 69

Installing the Nozzle Station

3.4.7.2 Installing the Nozzle Station

► Remove the downholder on the right above the reject bin.

► Fit the nozzle station [03073328-xx] with two screws in its mounting position (1).

► Depending on the machine configuration (see "3.4.7.3.1 Configurations with Reject Bins and Coding

Sheet" [ ➙ 70]) insert the reject bin [03048638-xx] and the component reject bin up to 6x6

[03062378--xx]. The reject bin mustn't be higher than the conveyor side wall in any case.

► Fasten the downholder left [03079173-xx] above the reject bin [03048638-xx] (see "3.4.7.3.2 Install

ing/Removing Downholder" [ ➙ 73]).

► Insert the coding sheet at unoccupied bin locations [03083883-xx] (see "3.4.7.3.3 Installing/Remov

ing Coding Sheet" [ ➙ 74]).

► Install the valve for the nozzle station [03055785-xx] (4) at the COT insert using the two DIN912-

M2,5 x 16-A2-70 screws [00350291-xx].

► Replace, unless already performed, the QSC-6H plug at the solenoid valve feed control with the Y

press-fit connection with push-on socket QSY-6H-4 [03055792-xx].

► Plug the hose PUN-CM 4x0.75 / 200mm [03056096-xx] into the pneumatic connection to the nozzle

changer (5) and into the pneumatic connection of the nozzle changer (6) or close it with the plug

QSC-4H [00330249-xx].

► Plug the hose PUN-CM 4x0.75 / 135mm [03056097-xx] into the pneumatic connection to the nozzle

changer [03055785-xx] (3) and to the pneumatic connection of the nozzle changer (2).

► Connect the cable "Cable feed X series: nozzle station" [03053223-xx] which has already been con

nected in the COT insert with the "valve for nozzle station cplt." [03055785-xx].

► If the verify reject bin option is already installed, the sensor for this reject bin has to be installed at

another position. For this, use the metal sensor MK2 prefitted (reject bin 6x6) [03080138-xx]. For fur

ther information please refer to the Assembly Instructions Reject Bin SIPLACE SX1/2 [00196615-

xx].

Installing the nozzle station

Legend

1. Fixation points of the nozzle station [03073328-xx]

2. Pneumatic connection on the nozzle station

3. Pneumatic connection to the nozzle station

4. Valve for the nozzle station [03055785-xx]

5. Pneumatic connection to the nozzle changer

6. Fixing screw of the mounting plate

7. Pneumatic connection on the nozzle changer

NOTICE

The mounting plate for the solenoid valve is fastened and fixed in position with one screw only

(6). If necessary, loosen this mounting plate to install the solenoid valve.

Attention: the connector left to the solenoid valve is also fastened to this plate.

Installing the CPP Placement Head

Assembly of the CPP Placement Head Height Adjustment and Installation of the Nozzle Station

70 Assembly Instructions / Montageanleitung Head Reconfiguration Kit CPP

Installing the Downholder and the Co ding Sheet

3.4.7.3 Installing the Downholder and the Coding Sheet

Depending on the configuration of the SX machine either the reject bin [03063238-xx] with downholder

[03079173-xx] or the component reject bin up to 6x6 [03062378--xx] is used on occupied box locations.

On unoccupied bin locations the coding sheet (No Box) [03083883-xx] has to be installed.

For the description of the configurations refer to "3.4.7.3.1 Configurations with Reject Bins and Coding

Sheet" [ ➙ 70].

For the description of the installation and the removal refer to "3.4.7.3.2 Installing/Removing Downhold

er" [ ➙ 73] and "3.4.7.3.3 Installing/Removing Coding Sheet" [ ➙ 74].