00197465-01_SM_CP20-A-M_EN.pdf - 第6页
1 Introduction 1.1 Safety Instructions 1.1.2 Safety Instructions for the Compre ssed Air Supply 6 Service Manual SIPLACE C&P20, C&P20A, C&P20M 1.1.2 1 . 1 . 2 S a f e t y I n s t r u c t io n s f o r t h e C …
1 Introduction
1.1.1 Conventions for the use of safety instructions 1.1 Safety Instructions
Service Manual SIPLACE C&P20, C&P20A, C&P20M 5
1
1 Introduction
Introduction
This service guide is a manual or reference work for performing service work on the SIPLACE® C&P20,
C&P20A and C&P20M placement head types.
1.1
1.1 Safety Instructions
Safety Instructions
1.1.1
1.1.1 Conventions for the use of safety instructions
Conventions for the use of safety instructions
This manual contains notes that must be observed to guarantee your personal safety and to avoid dam
-
age to equipment. These notes are highlighted by warning triangles and are indicated as follows accord
-
ing to the level of risk:
DANGER
Nonobservance of these safety instructions may cause injury to personnel and damage to the
machine!
► Please observe the safety instructions in the user manual of the relevant machine for all
work!
DANGER
Definition
For the purposes of this manual, this indicates that fatal or severe injuries or considerable dam
-
age to property will occur if this hazard warning is not observed.
WARNING
Definition
For the purposes of this manual, this indicates that fatal or severe injuries or considerable dam
-
age to equipment may occur if these warning instructions are not followed.
CAUTION
Definition
For the purposes of this manual, this indicates that minor injuries or damage to property may
occur if this caution is not observed.
NOTICE
Definition
For the purposes of this manual, this note provides information about the product or indicates
a part of the manual that requires particular attention.
1 Introduction
1.1 Safety Instructions 1.1.2 Safety Instructions for the Compressed Air Supply
6 Service Manual SIPLACE C&P20, C&P20A, C&P20M
1.1.2
1.1.2 Safety Instructions for the Compressed Air Supply
Safety Instructions for the Compressed Air Supply
1.1.3
1.1.3 Safety Instructions on Hazardous Materials
Safety Instructions on Hazardous Materials
CAUTION
Risk of injury from compressed air!
Risk of injury when disconnecting the compressed air lines.
► NEVER disconnect compressed air lines while they are still pressurized.
CAUTION
Prolonged interruptions to the compressed air supply can cause damage.
When the machine is switched on, do not use the shutoff valve to interrupt the compressed air
supply for more than 30 minutes.
► If you need to shut off the compressed air system for longer, in order to carry out mainte
-
nance or servicing work, you must switch the machine off at the main switch and disconnect
it from the power supply.
CAUTION
Observe the safety data sheets
Observe the applicable safety data sheet, when handling hazardous materials (e. g. Loctite
241, ethanol).
1 Introduction
1.1.4 Laser Classification 1.1 Safety Instructions
Service Manual SIPLACE C&P20, C&P20A, C&P20M 7
1.1.4
1.1.4 Laser Classification
Laser Classification
1.1.4.1
1.1.4.1 Laser Class 1
Laser Class 1
Classification of the Whole Machine
Classification of the Camera Systems
1.1.4.2
1.1.4.2 Laser Class 1M
Laser Class 1M
1.1.4.3
1.1.4.3 Laser class 2
Laser class 2
NOTICE
Laser class 1 and 1M
Modules in laser classes 1 and 1M are not labeled.
All installed camera systems and the whole machine (when ready for oper
-
ation) are assigned to laser class 1.
The laser classes are determined according to DIN EN 60825-1:2001.
The following camera systems are assigned to laser class 1:
▪ Stationary component cameras for the SIPLACE TwinStar (TwinHead)
and the SIPLACE Multistar (CPP)
▪ Component camera, stationary, P&P, type 33, 55 x 45, digital
▪ Component camera, stationary, P&P, type 25, 16 x 16, digital
▪ Component camera, stationary, P&P, type 36, 32 x 32, digital
Do not look directly at this with optical instruments!
The following camera systems are assigned to laser class 1M:
▪ CO camera C&P, type 23, 6 x 6 on the SpeedStar
▪ CO camera C&P, type 41, 6 x 6 on the SpeedStar
▪ CO camera C&P, type 30, 27 x 27 on the MultiStar
▪ CO camera C&P, type 30, 18 x 18 on the 12-segment Collect&Place
head
Laser radiation
Do not look into beam!
The following modules are assigned to laser class 2:
▪ PCB barcode scanner
▪ Component sensor on the SpeedStar
▪ Component sensor on the MultiStar
The entire machine is classified as laser class 2 if the coplanarity laser mod
-
ule option is installed.