00194579-0202.pdf - 第35页
Retrofit instructions Wide board 242 / 508 mm SIPLACE HS-60 / D4 08/2006 Edition 37 The picture below illustra tes the possible maximum c onveyor wid ths for dual conveyors of the va- rious machine types. 2 2 Fig. 2.1 - …
Retrofit instructions Wide board 242 / 508 mm SIPLACE HS-60 / D4
08/2006 Edition
36
2
Tab. 2.1 - 2 Guide values for the minimum and maximum conveyor widths
2
This gives for the maximum conveyor width on a line: 2
The maximum conveyor width on a line of machines is determined by the machine with the smal-
lest maximum conveyor width. This means, for example, if there are type HS-60 / D4 and HF-
series machines on a line, the maximum conveyor width is determined by the HS-60. 2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
Machine type 2 Single
conveyor
[mm] 2
Dual con-
veyor [mm] 2
Flexible conveyor (one
conveyor track widened)
[mm] 2
HF standard width 2 50 - 460 2 50 – 216 2 50 – 416 2
HF (Wide HS-60) 2 50 - 508 2 50 – 242 2 50 – 380 2
HF (Wide HF series) 2 50 - 508 2 50 – 250 2 50 – 450 2
S-27 HM standard width 2 50 - 460 2 50 – 216 2 50 – 380 2
HS-60 standard width 2 50 - 460 2 50 – 216 2 50 – 380 2
HS-60 (Wide HS-60) 2 50 - 508 2 50 – 242 2 50 – 380 2
Retrofit instructions Wide board 242 / 508 mm SIPLACE HS-60 / D4
08/2006 Edition
37
The picture below illustrates the possible maximum conveyor widths for dual conveyors of the va-
rious machine types. 2
2
Fig. 2.1 - 1 Illustration of the various conveyor widths
The wider conveyor increases the placement area of the machine. For positions that are at the
outer edge of the placement area, this can lead to problems with the distance between the gan-
tries of a processing area. The minimum distance is reduced by 10 mm by the installation of the
old reflector. If an old reflector is installed, the grease nipple must be replaced with a setscrew
(since the grease nipple can cause problems in conjunction with an old reflector). 2
Retrofit instructions Wide board 242 / 508 mm SIPLACE HS-60 / D4
08/2006 Edition
38
PCB and head mapping 2
During system acceptance, the HS-60 is mapped as before, i.e.: 2
Single conveyor with the mapping test board 520 x 460 (item no.: 00325743-02) 2
Dual conveyor with the mapping test board 520 x 380 (item no.: 00375916S01) (for each conveyor
track) 2
If there is demand for the Wide board for the HS-60, then the following mapping test boards should
be used: 2
Single conveyor "mapping test board HF 508x450“(00373952-01) 2
2.2 Restrictions for the HS-60 / D4 with "Wide HS-60"
– For individual products (PCBs), the reduced distance between the gantries and the resulting
waiting times can lead to slight deviations in the actual placement rate compared to the place-
ment rate calculated in SIPLACE Pro. This applies particularly if there are a large number of
placement positions near the newly set stationary side wall and if the gantry used for place-
ment is not using the optimum path. This can be minimized using the placement sequence.
– Feeder modules: Only feeder modules from the S series can still be fitted. Linear feeders, bulk
case feeders, manual trays and all special design or third-party modules are not permitted. The
widening of the placement area causes the pick-up and placement areas to overlap. Linear
feeders, manual trays, MTCs and TrayStak feeders are not regarded as standard feeders. This
is not checked by the programming system and it is thus the responsibility of the customer to
carry out this check.
– The synchronous dual conveyor is not possible with this configuration since the wrong offset
would be used for the calculation in the programming system.
2
– More maintenance is required since the grease nipples on the guide carriages were replaced
with grub screws in order to avoid a crash. The grease nipples on the guide carriages must be
refitted temporarily in order to maintain the guide carriages. The grease nipples should be re-
moved once more after the maintenance. This is the responsibility of the customer.
– In this configuration, the ceramic substrate centering feature and special designs already fitted
to the lifting table are not possible. Adaptation based on a special design is available upon re-
quest.
– On the dual conveyor with "Wide HS-60“ and single conveyor configuration, the conveyor width
is limited to 380 mm rather than the 430 mm which is mechanically possible.
– There is no productivity lift available for this option.