00196845-02_AI_Vakuumpumpe_SXDX4_X-Serie-S_de_en.pdf - 第113页
Maintenance 4.1.1 Tools, Consumables, Spar e and Wear Parts Maintenance Tasks for Vacuum Pump Vacuum Pump Vakuumpumpe 113 4 4 M a in t e n a n c e Maintenance 4.1 4 . 1 M a in t e n a n c e T a s k s f o r V a c u u m P …
Fitting the Vacuum Pump
Retrofit compressed air supply 3.2.21 Final Work:
112 Vacuum Pump Vakuumpumpe
3.3
3.3 Retrofit compressed air supply
Retrofit compressed air supply
NOTICE
Scheduled modification at the proportional controller (pressure control valve)
The scheduled modification is related to all machines where all heads are operated with vacu-
um pumps.
In future one of the two proportional controllers [03065425-xx] is inapplicable. The compressed-
air piping will be converted accordingly at this place for the placing/holding circuit.
► If the proportional controller is missing remount it in case of a retrofit to compressed air op-
eration.
⇨ More information in detail was not available at the copy deadline.
Maintenance
4.1.1 Tools, Consumables, Spare and Wear Parts Maintenance Tasks for Vacuum Pump
Vacuum Pump Vakuumpumpe 113
4
4 Maintenance
Maintenance
4.1
4.1 Maintenance Tasks for Vacuum Pump
Maintenance Tasks for Vacuum Pump
SXDX4
X34iS
4.1.1
4.1.1 Tools, Consumables, Spare and Wear Parts
Tools, Consumables, Spare and Wear Parts
▪ If needed, filter insert [03077677-xx]
SXDX4 X34iS
▪ Assembly instructions for vacuum pump X series S, SX4/DX4 [00196845-xx]
▪ Service manual for your machine
NOTICE
Observe the maintenance instructions
The following chapters are only excerpts from the maintenance manual.
► Refer to the maintenance manual for your machine if you need complete information about
maintenance of the vacuum pump and C&P20A.
NOTICE
SX4/DX4: The vacuum pumps are options.
The vacuum pumps are located at locations 1 and 4, each behind the COT insert.
► Carry out the maintenance tasks on all vacuum pumps in your machine.
NOTICE
X series S: locations 1 and 4
The vacuum pumps are located at locations 1 and 4, each behind the COT insert.
► Carry out the maintenance tasks on all vacuum pumps in your machine.
Maintenance
Maintenance Tasks for Vacuum Pump 4.1.2 Preparatory Steps
114 Vacuum Pump Vakuumpumpe
4.1.2
4.1.2 Preparatory Steps
Preparatory Steps
► Switch off the machine and secure it to prevent unauthorized reactivation. Observe the instructions
in section "1.2 Preparatory Work..." [ ➙ 72].
► Interrupt the compressed air supply to the machine.
► Dismantle the waste slide. Read the service manual for your machine first.
SXDX4 X34iS
4.1.3
4.1.3 Recommended maintenance intervals
Recommended maintenance intervals
► Dismantle the cover plate (1) incl. the fan over the
vacuum pump.
CAUTION!
Make sure you do not damage any cables and hoses.
CAUTION
Loosened vacuum pump
It is possible to remove the vacuum pump from the machine but it is not necessary.
For a better access, however, it may be useful to loosen the vacuum pump and pull it a bit to
the front within the machine. Also read the Assembly Instructions for the vacuum pump.
► Make sure that the vacuum pump cannot fall out of the machine.
Maintenance inter-
val
Spare part Task
Every 6 months Filter insert [03077677-xx] Check the filter insert and replace if necessary.
NOTICE
Working life
The filter insert has a working life of at minimum 7500 hours up to 25000 hours. For more infor-
mation about the product life, refer to the manufacturer's documentation (see http://www.beck-
er-international.com – Vacuum pump rotary vane pumps, dry running, type VX4.25)