00193893-04.pdf - 第57页
SIPLACE HF Series Head Reconfiguration Kits 2 Retrofit in structions - SIPLACE HF seri es head reconfiguration kits 05/2006 Edition 57 2 Retrofit instructions - SIPLACE HF series head reconfiguration kit s 2.1 Possible g…
1 Nachrüstanleitung Head Reconfiguration Kits SIPLACE HF-Serie Head Reconfiguration Kits SIPLACE HF-Serie
Ausgabe 05/2006
56
SIPLACE HF Series Head Reconfiguration Kits 2 Retrofit instructions - SIPLACE HF series head reconfiguration kits
05/2006 Edition
57
2 Retrofit instructions - SIPLACE HF
series head reconfiguration kits
2.1 Possible gantry/placement head installation posi-
tions
You cannot install any placement head type on any gantry. The overview below shows the possi-
ble positions:
2
2
2
2
2
Machine type 2
Placement area 1
Gantry 2
Placement area 2
Gantry 2
1 2 4 2 2 2 3 2
119600
SIPLACE HF
placement machine
2
TH 2 - 2 - 2 TH 2
6 2 - 2 - 2 TH 2
12 2 - 2 - 2 TH 2
6 2 - 2 - 2 6 2
12 2 - 2 - 2 12 2
12 2 - 2 - 2 6 2
119650
SIPLACE HF/3
placement machine
2
12 2 12 2 - 2 12 2
6 2 6 2 - 2 6 2
12 2 12 2 - 2 6 2
12 2 6
2 - 2 6 2
6 2 12 2 - 2 6 2
12 2 12 2 - 2 TH 2
12 2 6 2 - 2 TH 2
6 2 12 2 - 2 TH 2
6 2 6 2 - 2 TH 2
2 Retrofit instructions - SIPLACE HF series head reconfiguration kits SIPLACE HF Series Head Reconfiguration Kits
05/2006 Edition
58
2.2 Safety instructions
WARNING
The safety instructions from the “Operational safety” chapter of the user manual and servicing in-
structions take precedence over these instructions. 2
The SIPLACE placement machines are supplied with main power voltage.
Consequently parts of these systems carry dangerous voltages! This voltage is present at certain
modules inside the machine base, even when the machine is switched off at the main power
switch.
Incorrect handling of the placement machine or touching live parts of the machine can result in
death or severe injury, and considerable damage to equipment.
BEFORE starting any work, shut down the operating system correctly, then switch the machine
OFF at the main power switch and disconnect from the main power supply. In addition, the com-
pressed air supply must be switched off at the compressed air unit's main valve in the machine
base and vented by actuating the needle valve on the compressed air unit.
There is DANGER for heart pacemaker wearers in the vicinity of the linear motors, as described
in detail in the "Special safety instructions for working in the vicinity of strong magnetic fields"
section of the user manual and service manual.
Always follow the accident prevention regulations, DIN or other standards and special safety
rules applicable in your country.
Pay attention to the information concerning residual voltages in the Operational Safety chapter.
Follow the ESD regulations as described in the operational safety section of the operating
instructions.
During the retrofit, always secure the machine to prevent access by other people and to prevent
it being switched on again. The procedure is described in the “Locking the machine…” section of
the user manual.
Working with the SITEST program further increases the risk of accident.
The SITEST program must only be used by authorized and trained personnel.
2
2.2.1 Explanation of the symbols
2
2
2
Please note 2
2
2
2
Caution 2