7OM-1603-006_w.pdf - 第59页
7OM-1603 1-18 Chapter 1 : 3. Name of Each Section and Handling 3.4.1 Attachment Procedure of Pallets NOTICE Be sure to insert a pallet horizontally into the magazine. Otherwise, the traverse cannot pull out the pallet, c…
7OM-1603
Chapter 1 : 3. Name of Each Section and Handling
1-17
3.4 Magazines
CAUTION
Because the magazine is heavy, take care handling
it when it is moved. Otherwise, you might injure
your arm or waist.
NOTTICE
In the case that the total mass of the magazine exceeds
20 kg, it should be lifted and moved by two people.
The magazines are provided with a mechanism that install the pallets (the pallets
loaded with trays). By replacing a magazine with another one (loaded fully with
components), the feeder can be loaded collectively with components.
•
Case : "Total Thickness ≤ 8 mm"
15-Step Magazine (15 pallets/1 magazine), 12 mm Pitch
Notice
(a) Do not put a magazine on another one.
No object should be put on the upper surface of the machine, either.
A deformed magazine may cause the feeder to break down.
(b) Beforeplacingamagazineontheoor,besuretoconrmthatthere
is no foreign substance such as dirt and dust on the bottom surface
of the magazine.
If a magazine is used with the bottom surface being dirty (adherence
of dirt and dust), the feeder works with the magazine being tilted and
may break down.
(c) Do not put any seals or tapes on the side faces of the magazine.
Otherwise, the magazine will malfunction.
•
Total Mass (Full Capacity) of Magazine
The total mass is 40 kg (determined by the formula "(Weight of Pallets +
Components in Trays) × Number of Steps").
1102-003
7OM-1603
1-18
Chapter 1 : 3. Name of Each Section and Handling
3.4.1 Attachment Procedure of Pallets
NOTICE
Be sure to insert a pallet horizontally into the
magazine.
Otherwise, the traverse cannot pull out the pallet, causing
the components in the tray of the pallet to disperse or the
machine to be damaged.
Procedure
(1) Open the magazine door.
Notice
When the feeder is operated with the magazine door being
deformed, it may break down.
(2) Observe the right and left stage Nos. and insert the tray-loaded pallet into the
magazine.
Notice
•
When a pallet is to be inserted into the magazine, make sure that
the pallet is inserted correctly with its top side facing upward.
When the pallet is inserted upside down, a breakdown will result
because the error cannot be detected.
•
The use of the pallet for GXH-1/3 is not available.
When the pallet for GXH-1/3 is installed onto the magazine, the
magazine door can not be closed completely.
(3) Close the magazine door.
Notice
Be sure to close the magazine door slowly and securely. Otherwise,
some components may pop out of the tray.
If the magazine door is not closed securely, the magazine may open
while the feeder is running and the feeder may break down.
3.4.2 Detachment of Pallets
Procedure
(1) Open the magazine door.
(2) Pull out the desired pallet from the magazine.
1007-003
7OM-1603
Chapter 1 : 3. Name of Each Section and Handling
1-19
3.4.3 Replacement of Magazine
•
Attachment Procedure of Magazine
Procedure
(1) Conrm that the LED of the [READY] switch is "OFF" and then open the
door.
Note
When the LED illuminates in green, the door cannot be opened.
(2) While pulling out the magazine stopper knob forward, turn it clockwise by
approximately 90°.
Knob
While pulling out the knob forward, turn it clockwise by approximately 90° .
2
1
Magazine Base F7A7
1007-002