SOM-1619-001.pdf - 第10页

10 Tg0590-PM-SO 0301-002 4. PCB Origin Of fset T each *1 1 Control Switch When the [ENABLE] button is pressed on the operation panel within two seconds after the "Move" [ON] button is pressed, the device is act…

9 Tg0590-PM-SO0301-002

4. PCB Origin Offset Teach

*5 [TEACH] Button

The teaching operation is performed at the present position.

*6 Pattern Program Window

It consists of the following items.

Total Step

The number of total steps in the pattern program is indi-

cated.

U, P, O

The presently referred step in the pattern program is indi-

cated.

Placement Data X[mm], Y[mm], Z (deg), Fdr, Component

The current placement data is indicated.

The temporarily entered step is shown with a blue back-

ground.

[Desig Step] Button

Any step can be indicated.

*7 Teach Point

The teaching mode for the step to be taught is selected.

1-Pt

This is selected when the teaching operation is performed at

the center of the component.

2-Pt

This is selected when the teaching operation is performed

for a component larger than the P.E.C. recognition camera

view limit.

*8 Recognition Area

The image taken by the P.E.C. recognition camera is displayed.

*9 [Cancel] Button

The temporarily entered teach data is cancelled.

*10 [End] Button

The placement position teach operation is ended.

Whether or not the teach results are saved can be selected.

10 Tg0590-PM-SO0301-002

4. PCB Origin Offset Teach

*11 Control Switch

When the [ENABLE] button is pressed on the operation panel

within two seconds after the "Move" [ON] button is pressed,

the device is activated.

4.2 PCB Origin Offset Teach Operation Procedure

••

• Operation Procedure

(1) Select the [Move to Teach Pt] button *4 and then press the

"Move" [ON] button *11. Then, within two seconds, press the

[ENABLE] button on the operation panel.

The X/Y table will move to the teach point where automatically

judged in the pattern program, the P.E.C. recognition mark or

component outer shape display and land are displayed within the

window size.

(2) Check the view of the P.E.C. recognition mark or component

outer shape display and land displayed within the window size.

(3) When the teach point is the P.E.C. recognition mark, press the

[TEACH] button *5 and then, within two seconds, press the

[ENABLE] button on the operation panel. The P.E.C. recognition

will be performed. When the recognition is completed normally,

the new PCB origin offset (X, Y) is displayed in the teach result

box.

(4) When the teach point is the placement position, select [1-Pt] or

[2-Pt] button in the "Teach Point" box *7.

When the entire component's outer shape is within the

window size:

Select [1-Pt] button (Component Center) for the Teach Point

When the entire component's outer shape is not within the

window size:

Select [2-Pt] button (Opposite Angles in Component) for the

Teach Point. When [2-Pt] button is selected, the PCB pattern

moves to the second point after completing the teaching of first

point.

11 Tg0590-PM-SO0301-002

4. PCB Origin Offset Teach

(5) Check the setting of Teach Point. Press the [TEACH] button *5

and then within two seconds, press the [ENABLE] button on the

operation panel. The teaching operation will be performed.

(6) Manipulate the pointing device to accommodate the component

outer shape image within the window size to the PCB pattern

entered in the recognition memory image.

Operation of Pointing Device

Joy Stick : Movement of the X/Y table (PCB

Pattern)

Right Click : Enlargement of Image

Left Click : Reduction of Image

Click on the Right and Left at the same time

: Positioning Completion

When the positioning is completed, the new PCB origin offset is

displayed in the "Teach Result (X, Y)" box *2.

(7) When the new PCB origin offset is temporarily entered, press the

[Temp Entry] button *3.

The new PCB origin offset is temporarily written in the temporary

file.

(a) Temporarily entering new PCB Origin Offset saves

the temporary file in the data for the operation and

pattern program file, but does not overwrite the

original file.

(b) Cancellation of temporarily entered data is available

during the temporary enter operation. To cancel,

press the [Cancel] button *9.

(8) Check the temporarily entered data using the placement step

operation.

Press the [Place Pos] button *1.