SOM-1619-001.pdf - 第17页
17 Tg0590-PM-SO 0301-002 5. Placement Position T each *9 [Cancel] Button The temporarily saved teach data is cancelled. *10 [End] Button The new placement position teach result is saved and the teaching operation is ende…
16 Tg0590-PM-SO0301-002
5. Placement Position Teach
*4 [Temp Entry] Button
The coordinates currently indicated in the placement position
teach operation are temporarily entered.
*5 Recognition Area
The image taken by the recognition camera is indicated.
*6 Pattern Program Indication
It consists of the following items.
Total Steps
The total number of steps in the pattern program is indi-
cated.
U, P, O
The steps in the currently referred pattern program are
indicated.
P-Data (Temp Data) X [mm] Y[mm], Z (deg), Fdr, Compo-
nent ID
The current placement position is indicated.
The temporarily entered data is indicated with a blue back-
ground.
[Desig Step] Button
Any step can be indicated.
*7 Operation Mode
When the operation mode is selected and the "Move" [ON]
button is pressed, the X/Y table is moved to the designated
position.
Auto Move
The automatic operation is performed.
Each pressing of the [Auto Move] button changes the speed
to high, middle and low in that order.
Step Move
The step movement is performed.
Zero Table XY
The X/Y table is returned to the origin.
*8 [TEACH] Button
The teaching operation is performed at the present position.
17 Tg0590-PM-SO0301-002
5. Placement Position Teach
*9 [Cancel] Button
The temporarily saved teach data is cancelled.
*10 [End] Button
The new placement position teach result is saved and the
teaching operation is ended.
*11 Control Switch
When the [ENABLE] button is pressed on the operation panel
within two seconds after the "Move" [ON] button is pressed, the
device is activated.
5.2 Placement Position Teach Operation Procedure
(1) In order to obtain the deviation tendency of PCB pattern, Select
the [Auto Move] button *7 and then "Move" [ON] button *11.
Then press the [ENABLE] button on the operation panel within
two seconds. Otherwise, press the [Step Move] button *7 and
then "Move" [ON] button *11. Then press the [ENABLE] button
on the operation panel within two seconds. The X/Y table is
moved.
(2) During the X/Y table movement, check the component outer
shape indicated within the window size and pattern condition.
If there is any deviation particular to a certain step, perform the
P-data teaching operation. If the pattern on the unit PCB is
entirely deviated, perform the O-data teaching operation.
(3) Move to the Teach Position
The two ways to move to the Teach Position are as follows:
• Move the X/Y table to the step to be taught using the Auto
Move operation and stop it by using the [STOP] button on the
operation panel.
When step moving, the step is normally scanned for the com-
ponents in order of the placement. The scanning can be fixed
by using U-No., P-No., O-No., and Fdr-No.
18 Tg0590-PM-SO0301-002
5. Placement Position Teach
When *6 Step is pressed, a key icon is displayed and the step
(consistent with the description displayed by the key icon) is
scanned. Two or more key icons can be selected.
Example
When the step is set to 101 for Fdr-No. and Fdr-No. is fixed,
only the steps with the Fdr. No. of 101 are scanned, regardless
of the U-No., P-No., and O-No. Moreover, if the U-No.1 is fixed
additionally, only the steps with U-No. 1 and Fdr. No. 101 are
scanned.
To designate the speed of the Auto Move, each
pressing of the [Auto Move] button changes the speed
to high, middle and low in that order.
• Indicate the step to be taught by using the vertical scroll bar in
the pattern program indication and select the step. Select the
[Step Move] button *7 and "Move" [ON] button *11. Then,
within two seconds, press the [ENABLE] button on the opera-
tion panel.
(a) When the [Desig Step] button *6 is selected on the
lower left of the pattern program indication, the step
can be entered using the ten-key.
(b) The order of step indication on the pattern program
indication is not the same as the order of compo-
nent placement, but U1, P1, 01 → U1, P2, 01 → ...
→ U1, P1, 02 → ... → U2, P1, 01 → ... → Un, Pn,
On, in this order.
(4) Check the component outer shape indicated within the window
size and the view of the land pattern or component, and select
1-Pt or 2-Pt in the "Teach Point" *1.
Teaching at the Center of the Component
Select [Center 1pt (MFOV)] for the teach point setting.
If the component size is too large to include its outline
in the camera view, the shooting is automatically
divided and the image taken is synthesized. Image
taken is divided into max. 25 pieces.
Teaching at 1 point in the center without dividing the
image.
Select Center 1pt (SFOV).