00198235-02_VD_710.1_R17-1_DE_EN.pdf - 第24页
Station Software 71 0.1 (R17 - 1) / Versio n Description 06/2017 Edition 24 9 Important Term s and Abbreviations CA4 Machine type of the Chip Assembly (CA ) - series with 4 g antries and 2 PAs C&P Collect & Place…
Station Software 710.1 (R17-1) / Version Description 06/2017 Edition
23
710.0 Patch 1
Error no. Error description
D1-127726801 There was a message for all four heads that the vacuum was not sufficient.
D1-129449544 eSW: the board was aborted when moving into PA2 but no errors were
displayed.
D1-135009301
D1-135456301
D1-135752301
The station stopped with a track error at the IPTE stick feeder but no error
message was displayed.
D1-135572407 Teaching did not work and a z-axis position error occurred.
D1-135681243 The overall endurance reference run could not be started.
D1-135712601 eSW: Opening and closing the cover lead to error message 30406 Power
output stage deactivated as a result of a faulty PWM
control signal
and the X-/Y-axes had to be referenced again.
D1-135745001 The reference run of the main axes failed.
D1-135752101 The WPC machine data could not be saved.
D1-135795401 After having corrected the pickup position, the station software did not respond
anymore.
D1-135841801 Calibrating the lifting table was not possible in Dual as single mode.
D1-135912801 There was a scale error when LED centering camera SST47 was used.
D1-135985601 A component on the glass plate was reported although there was none.
D17880-44541 All nozzles were thrown away after calibration.
D18082-6001 The machine stopped during production without any error.
D18093-11301 Changed placement offset after fiducials were whispered and the
measurement process was interrupted and then re-started.
D18263-1301 The cycle time was too long because the WPC and Twin Head were waiting
for the new board.
Table 8-5: Corrected errors station software version 710.0 Patch 1
Station Software 710.1 (R17-1) / Version Description 06/2017 Edition
24
9 Important Terms and Abbreviations
CA4 Machine type of the Chip Assembly (CA)-series with 4 gantries
and 2 PAs
C&P Collect & Place
CPP Collect & Place & Pick & Place
DC Dual Conveyor
DX1/DX2 Machine type with 1 or 2 gantries and 1 PA
EDIF Electronic Design Interchange Format
eWLP embedded Wafer Level Process
FOPLP Fan-Out Panel Level Packaging
FCCS Field Camera Calibration System
GUI Graphical User Interface
HFH High Force Head
HW Hardware
MGCU Modular Gantry Control Unit
MHCU Modular Head Control Unit
MTC Matrix Tray Changer
OIS Operator Information System
PA Processing area
PCB Printed circuit board
Placement mode:
2-in-1
When a machine runs in I-Placement mode, it is possible to
perform manual operations for one side / gantry. This placement
mode is also called "independent".
Placement mode:
Alternating
Placement mode in a dual gantry placement area, in which both
gantries place components on both boards in a dual conveyor.
First, both gantries place all assigned components on the board
in lane one and then on the board in lane two.
Placement mode:
Borrow
Performance
A line runs in I-Placement mode and to get a balanced
throughput between the left and right conveyor lanes, e.g. the
last machine runs in Alternating mode and places components in
this placement area on the board of the other lane.
Placement mode:
I-Placement
Placement mode in a dual gantry placement area in which each
gantry only places components on the board of the assigned
conveyor lane.
SC Single Conveyor
SC SIPLACE Setup Center (external setup control system)
SW Software
SWS SIPLACE Wafer System
SX1/SX2 Machine type with 1 or 2 gantries and 1 PA
TH Twin Head
TH HF Twin Head High Force
Station Software 710.1 (R17-1) / Version Description 06/2017 Edition
25
Twin VHF Very High Force Twin Head
TX1/TX2/TX2i Machine type with 1 or 2 gantries and 1 PA
TX2 micron/
TX2i micron
TX2i micron 15 µm
Machine type with 2 gantries and 1 PA
VC Vision computer
VCU Vision Control Unit
VHF P&P Very High Force Pick&Place
WLFO Wafer Level Fan-Out, Chip Assembly process
WPC Waffle Pack Changer
X2/X2 S Machine type with 2 gantries and 2 PAs
X3/X3 S Machine types with 3 gantries and 2 PAs
X4/X4 S/
X4 S micron
Machine types with 4 gantries and 2 PAs
X4i/X4i S
X4i S micron
Machine types with 4 gantries and 2 PAs