5M-1751-004w_G5S.pdf - 第21页

Safety Precautions Safe-12 1OM-1751 Alert Indications described as " CAUTION " (continued) Alert Description Related Items Do not put your hand in the moving area while the feeder base is moving up or down. Whi…

100%1 / 190
Safety Precautions
Safe-11
1OM-1751
1305-002
4. Alert Indications in Instruction Manual
Alert Indications described as "
CAUTION
" (continued)
Alert Description Related Items
When a tape feeder is attached or detached, be sure not to drop
it.
Otherwise, a foot injury will result or the feeder itself may be damaged.
Carefully handle each feeder one by one and do not drop any.
"3.8" in
"Chapter 1 (Vol. 1)"
"2.2.4" in
"Chapter 3 (Vol. 1)"
"3.1" in
"Chapter 3 (Vol. 1)"
"3.4.2" in
"Chapter 3 (Vol. 1)"
Hazardous to your hands and ngers!
·
Be sure to hold the handle to move the bank feeder change cart.
·
Be careful not to hit your hand against the cover while installing the
bank feeder change cart onto the main machine.
"3.8.1" in
"Chapter 1 (Vol. 1)"
Hazardous to your hands and ngers!
·
Be sure to hold the handle to move the bank feeder change cart.
"2.2.4" in
"Chapter 3 (Vol. 1)"
Watch your step!
·
Be careful not to hit your foot against the cart while moving the bank
feeder change cart.
Especially, the resistance against cart movement may change rapidly
when the oor is ragged and the cart gets caught on the oor or
a sheet is used and the cart gets caught at the edge or a slackened
portion of the sheet.
·
Make sure to insert the feeder into the deep end.
When the tape feeder is mounted onto the feeder carriage, make sure
that it has been inserted into the deep end and xed securely.
In the case that it has not been xed securely, the tape feeder might
fall, which might cause a lower leg injury or damage to the feeder.
"3.8.1" in
"Chapter 1 (Vol. 1)"
"2.2.4" in
"Chapter 3 (Vol. 1)"
Safety Precautions
Safe-12
1OM-1751
Alert Indications described as "
CAUTION
" (continued)
Alert Description Related Items
Do not put your hand in the moving area while the feeder base is
moving up or down.
While the LED of the Feeder Ready switches are being ickering, it
indicates that the corresponding feeder base is moving up and down.
"2.2.5" in
"Chapter 1 (Vol. 1)"
When you need to bend down to perform work, you may hit your
head on the tape feeder worktable and get injured.
"2.2.6.1" in
"Chapter 3 (Vol. 1)"
When the tape feeder connecting cable is connected to the tape
feeder, unless the tape feeder is held securely, the tape feeder
holding guide may come o and drop from the tape feeder unit.
Connect the cable with the tape feeder held securely.
"2.2.6.1" in
"Chapter 3 (Vol. 1)"
There are some heavy feeder models. When such feeders are
removed with one hand, the weight of the feeder removed from
the guide cannot be supported by one hand and the feeder might
drop. Remove the feeder using both hands to support it.
"2.2.6.2" in
"Chapter 3 (Vol. 1)"
The padlock key should be kept in such a way that nobody except the
personnel in charge of maintenance can supervise it.
"4.3" in
"Chapter 2 (Vol. 1)"
The load power to the motors, etc., is turned OFF but the setup
operation must be performed carefully when you put your hand
inside the machine. Avoid hand and nger injuries.
"2.3.5" in
"Chapter 3 (Vol. 1)"
"4.1" and "4.2.1" in
"Chapter 6 (Vol. 2)"
Even when the power breaker is set to "OFF", the primary line is
powered, making it possible to cause an electric shock.
Be sure to completely stop the power supply to the machine before
maintenance work.
"1.1" in
"Chapter 1 (Vol. 4)"
1305-002
4. Alert Indications in Instruction Manual
Safety Precautions
Safe-13
1OM-1751
Alert Indications described as "
CAUTION
" (continued)
Alert Description Related Items
Residual voltages may remain behind for a few minutes in the
internal devices of the machine after power interception.
Before performing maintenance work, wait until the charge lamps of
the DC power supply and the servo amplier go "OFF" in 10 minutes
or more after the power breaker is set to "OFF".
"1.1" in
"Chapter 1 (Vol. 4)"
After making sure that the air supply has been stopped and the
cutter blades are closed, start maintenance.
During maintenance, do not touch the cutter blade.
"4.6.2" in
"Chapter 1 (Vol. 4)"
1305-002
4. Alert Indications in Instruction Manual