AX501最新3.6x版英文操作手册.pdf.pdf - 第22页

4022 593 51894 Operatin g Man ual 09.01 AX-301/501, AX-3/5 22 2 2.6.2 Feeder handling on the FCM-II tr olley A Check if th e surfaces o f the feed er interf ace on both feed er and troll ey ar e clean fr om component s a…

100%1 / 47
4022 593 51894 Operating Manual
09.01 AX-301/501, AX-3/5 21
2
2.6 Feeder handling
2.6.1 Feeder handling on the A-series trolley
A Check if the surfaces of the feeder interface on both feeder and
trolley are clean from components and do not have any mechanical
damage.
B Check that the tape on the feeder is cut directly below the feeder.
C Check that the top foil is cut at least 100 mm below the feeder
D Place the top guide of the feeder in the required feeder slot
position (1). Use the numbering from 1 to 27.
Pull handle (2), keep the feeder straight and slide (3) the two
position-pins into the holes (4) until the clamping lever (5) locks
onto the locking axis of the trolley.
E If the feeder is placed correctly into the feeder trolley, the green
LED (1) blinks approximately 3 seconds where after it will remain
ON continuously.
Check/correct (with push button 3 or 4) the pick position of the
first component (2).
■ Remove a feeder in reverse order.
Figure 21 Feeder handling on the A-series trolley
>100 mm
A
1
4
2
3
5
D
1
3
4
2
B
D
E
C
4022 593 51894 Operating Manual
09.01 AX-301/501, AX-3/5 22
2
2.6.2 Feeder handling on the FCM-II trolley
A Check if the surfaces of the feeder interface on both feeder and
trolley are clean from components and do not have any mechanical
damage.
B Keep the feeder in horizontal position above the required feeder
slot position. Use the numbering from 1 to 44.
Lower the feeder, so the guide (1) will fall into the slotted hole.
Pull handle (2) and slide (3) the two position-pins into the holes
(4) until the clamping lever (5) locks onto the locking axis of the
trolley.
Make sure that the feeder runs straight and parallel with the slit
of the feeder bar during insertion.
C If the feeder is placed correctly into the feeder trolley, the green
LED (1) blinks approximately 3 seconds where after it will remain
ON continuously.
Check/correct (with push button 3 or 4) the pick position of the
first component (2).
■ Remove a feeder in reverse order.
Figure 22 Feeder handling
4
1
5
5
2
3
D
1
3
4
2
C
A
B
4022 593 51894 Operating Manual
09.01 AX-301/501, AX-3/5 23
2
2.7 Graphical user interface
The machine is operated via the touch screen. By touching the screen the
desired function can be activated. No keyboard is necessary. The
keyboard, located in the base under the touch screen, is for service
purposes only.
2.7.1 Conventions
Figure 23 Touch screen
Activating a button on the touch screen is indicated by a circle in this
manual. If more than one button has to be activated, the sequence is
shown by numbers.
2.7.2 Touch screen lay-out
The screen is divided into the following panels:
Figure 24 Touch screen, lay-out
ATitle panel:
Shows general information of the system.
B Command panel:
Contains main buttons to start or stop the production.
C Navigation panel:
Is used to switch between the different functional environments of
the graphical user interface.
D Sub navigation panel:
Is used to switch between the available information panels within
one functional environment.
EInformation panel:
Shows all information that belongs to a selected function.
2
3
1
B
D
E
C
A