YS24X_Mainte_E.pdf - 第15页
xii Safety instructions 2.2 T ypical warning text found in manual T he following are typical warning message text found in the Y AMAHA surface mounter or related product manual. 2.2.1 Safety instruction When you see the …
xi
Safety instructions
2. Safety message
This section describes information you should always comply with to prevent unforeseen accidents that might
lead to injury of the operator and others or damage the machine. Hazards and injuries that might result from
ignoring safety instructions and operating the machine incorrectly are categorized as follows.
2.1 Safety message and categories in this manual
This manual uses the following safety alert symbols, signal words, and format styles according to the degree of
hazard.
n
Safety alert symbols and signal words
w
WARNING
INDICATES A POTENTIALLY HAZARDOUS SITUATION WHICH, IF NOT AVOIDED, COULD RESULT IN DEATH OR SERIOUS INJURY.
THESE ARE POINTS MOST ESSENTIAL FOR PROTECTING THE SAFETY OF THE MACHINE OPERATOR, INSPECTOR AND SERVICE
PERSONNEL.
c
CAUTION
Indicates a potentially hazardous situation which, if not avoided, may result in minor injury, or material loss or damage
to the machine. These points are important for protecting the safety of the machine and data, etc.
n
NOTE
Gives helpful information or key points when operating the machine, in a simple and clear manner.
e
EMERGENCY STOP
THIS MARK INDICATES THE EMERGENCY STOP BUTTON MUST FIRST BE PRESSED BEFORE CONTINUING THE PROCEDURE.
xii
Safety instructions
2.2 Typical warning text found in manual
The following are typical warning message text found in the YAMAHA surface mounter or related product
manual.
2.2.1 Safety instruction
When you see the following cautions or warnings, always read them thoroughly and make sure you fully
understand them.
n
Warnings
w
WARNING
THE SIGNAL LIGHT (SIGNAL TOWER) INSTALLED ON THE TOP OF THE MACHINE IS AN IMPORTANT DEVICE THAT SHOWS THE
OPERATING STATUS OF THE MACHINE. BEFORE OPERATING THE MACHINE, MAKE SURE THAT EACH LAMP OF THE SIGNAL
TOWER LIGHTS UP CORRECTLY (GREEN DURING OPERATION, YELLOW WHEN ERROR OCCURS OR INTERLOCK IS DETECTED,
AND RED DURING EMERGENCY STOP). NEVER PLACE ANY PART OF THE BODY IN THE HEAD UNIT MOVEMENT RANGE WHILE
THE GREEN LIGHT IS ON. (ON MACHINES DESIGNED TO MEET EU SPECIFICATIONS, GREEN/WHITE/BLUE LAMPS ARE USED
INSTEAD OF GREEN/RED/YELLOW LAMPS.)
w
WARNING
NEVER ALLOW ANY PART OF YOUR BODY (HANDS, HEAD) TO ENTER WITHIN THE MACHINE MOVEMENT RANGE DURING
OPERATION.
w
WARNING
BE CAREFUL WHEN USING ISOPROPYL ALCOHOL, SINCE INHALING ITS FUMES OVER LONG PERIODS CAN BE HAZARDOUS
TO HEALTH.
n
Cautions
c
CAUTION
The person operating the machine must have been trained in correct machine operation and safety.
c
CAUTION
This machine contains parts generating strong magnetic fields. Great care should be taken when a part of your body
is put inside the machine for the maintenance work. Cautions regarding ferromagnetic fields are described in the
section, “Safety Instructions”, at the beginning of this document. Always thoroughly read this section to fully
understand its contents.
c
CAUTION
The exhaust air blow might strike your face, so be sure to wear safety goggles.
xiii
Safety instructions
2.2.2 Operation and handling precautions
When seeing the following cautions or warnings, always read them thoroughly and make sure to fully understand them.
n
Warnings
w
WARNING
INFLAMMATION MAY OCCUR IF GREASE OR LUBRICANT GETS IN THE EYES. BEFORE HANDLING THE GREASE, WEAR SAFETY
GOGGLES TO ENSURE THE GREASE WILL NOT COME IN CONTACT WITH THE EYES.
w
WARNING
INFLAMMATION MAY OCCUR IF THE GREASE OR LUBRICANT COMES INTO CONTACT WITH SKIN. BE SURE TO WEAR
PROTECTIVE GLOVES TO PREVENT CONTACT WITH SKIN.
w
WARNING
DO NOT TAKE ORALLY OR EAT THE GREASE OR LUBRICANT. EATING WILL CAUSE DIARRHEA AND VOMITING.
n
Cautions
c
CAUTION
Always stop the machine before installing the parts feeder into the machine. Hands or other parts of your body might
otherwise be caught in the moving parts.
c
CAUTION
During operation only press the emergency stop button in cases of emergency.
c
CAUTION
Always turn off the power with the correct procedure. Using hasty or incorrect procedures to turn off power might
damage the flash disk in the machine.
c
CAUTION
When installing push-up pins on the push-up plate, set them in positions where they will not interfere with the conveyor
rails or other parts when the push-up plate is raised.
c
CAUTION
When the machine you are using is not equipped with a nozzle station, you must change the nozzle by hand if it is not
a specified nozzle. In this case, always first press the emergency stop button.
c
CAUTION
If an abnormality occurs during warm-up, immediately stop the machine, find the cause of the problem and eliminate it.
c
CAUTION
When storing the grease after use, tightly close the cap of the grease tube or container to prevent dust and moisture
from entering inside. Store it in a dark place to avoid direct sunlight, and keep away from fire and heating sources.
c
CAUTION
After copying board data or system data into a USB flash memory, do not leave that data in the USB flash memory for
a long time. Use the USB flash memory just as a copy medium for backup data. Prepare other backup media
(CD, DVD, MO, etc.) to store backup data more safely.
c
CAUTION
You can also clean and grease the ball screw after removing the push-up plate. However, the push-up plate is heavy.
So, take great care during handling.
c
CAUTION
A strong air flow is exhausted during the cleaning blow. Always remove all nozzles attached to the heads before
starting the cleaning blow. Starting the cleaning blow while the nozzles are still attached may blow the nozzles away
from the heads causing the nozzles to break or become lost.