德森印刷机说明书之操作手册-4d1321fc284ac850ac024234.pdf - 第23页
深圳德森精密设备有限公司 Shenzhen Desen Pre cision Machine Co., Ltd. - 23 - Click “ board stop cyli nder moves ” cau ses CCD to m ove to PCB stop position, s tart PCB pos itioning adjustment. 1) 单击 “ 刮刀后退 ” ，将刮刀移动到后限位处； 1) Cl ick “ …
深圳德森精密设备有限公司
Shenzhen Desen Precision Machine Co., Ltd.
- 22 -
annealing under a room temperature of 25 ℃ or so (the specific use shall be subject to the use
direction). T he temperature of solder paste shall become the same as room temperature before
being decapped for use; and
6)
使用时应将锡膏均匀地刮涂在刮刀前面的模板上，且超出模板开口位置，保证刮刀运
动时能将锡膏通过网板开口印到 PCB 板的所有焊盘上。
6)
When in use, solder paste shall be evenly pasted on the formwork in front of the squeegee to
the position further than the formwork so that the squeegee in operation can print the solder
paste onto the screen
’
s
opening to all bonding pad s.
3.2.3
3.2.3
3.2.3
3.2.3
PCB
PCB
PCB
PCB
定位调试
3.2.3
3.2.3
3.2.3
3.2.3
Positioning
Positioning
Positioning
Positioning
and
and
and
and
debugging
debugging
debugging
debugging
of
of
of
of
PCB
PCB
PCB
PCB
board
board
board
board
1.
打开机器主电源开关。
Turns on the main power switch of the machine .
2.
进入印刷机主画面。
Enters the main screen of print ing machine.
3.
单击 [ 归零 ] 菜单，让机器运动部件回到原点部位。
Click [ Reset ] in the menu, lets the machine movement part return to default.
4.
单击主菜单栏 [ 文件 / 新建 ] ，并键入新建文件名。
Click [document/new], and enters the newly built filename
5.
单击主工具栏 1 “ 生产编辑 ” 图标，在输入密码后进入 [ 生产编辑 ] 中，进行 PCB 设置
，
输入所要生产的 PCB 板名称、型号、 长、宽、 厚和运输速度参数， 再单击 “ 宽度调 节
”
将运输导轨自动调到适宜所要生产的 PCB
宽度。
（详见第四章介绍）
C lick the main toolbar 1 “ production edit ” icon, enters password and start [production
edit], start PCB setup , inputs PCB board name, model number , l e ng th , width,
thick ness and transporting speed , click “ width adjustment ” to adjust the conveyer
automatically. (See Chapter IV for details)
6.
在生产编辑菜单中输入所要生产 PCB 板的各项参数，如刮刀速度、压力、脱模长度 和
速度、清洗方式、时间间隔和速度以及取象方式等。
Inputs PCB board parameter s into the menu of production edit , such as the
squeegee speed, the pressure, the length and speed of demoulding , the cleaning
method , the rate and time interval of cleaning, image taking manner etc.
7.
单击 “ 挡板气缸移动 ” 使 CCD 移动到停板位置，进行 PCB 定位校正。
深圳德森精密设备有限公司
Shenzhen Desen Precision Machine Co., Ltd.
- 23 -
Click “ board stop cylinder moves ” causes CCD to move to PCB stop position, start
PCB positioning adjustment.
1) 单击 “ 刮刀后退
”
，将刮刀移动到后限位处；
1) Click “ Squeegee back ” , moves the squeegee to back position ;
1)
再单击 “ 移动 ” 将挡板气缸移动到 PCB 停板位置，此时将 PCB 放到运输导轨进板
入口处， 再将 “ 停板气缸开关
”
打开， 停板气缸工作即气缸轴向下运动到停板位
置；
2) Then click “ Move ” to move the baffle cylinder to the position where the PCB board parks.
A
t
this time, put PCB board
at
the board entrance of transport guide rail and switch on “ Board
stop cylinder switch ” . T he board stop cylinder will work, namely, the cylinder shaft will move
downwards to the board stop position;
3) 打开 “ 运输开关
”
，将 PCB 板送到停板气缸位置，眼睛观察 PCB 板是否停在运输 导
轨的中间，如 PCB 板不在运输导轨中间，则需要调整停板气缸位置 —— 修改停板气缸
X ， Y 坐标， X 往 ← 为减 → 为加， Y 往位 ↑ 为减 往 ↓ 为加，直到 PCB 板位置合适；
3) Switch on “ Transport switch ” to send PCB board to the board stop cylinder position.
V
isually observe PCB board to see whether
it
stops
at
the middle of transport guide rail, if not,
its position shall be adjusted by changing the X and Y coordinates of the board stop cylinder:
going leftward along axis X will decrease the value and rightward will increase the value;
going upward along axis Y will decrease the value and downward will increase the value. T he
change shall not stop until the PCB board is
at
a proper position;
4) 再将 “ 运输开关 ” 关闭，同时打开 “ PCB 吸板阀
”
；关闭 “ 停板气缸
”
；打开 “ 平台 顶
板
”
开关， 工作台向上升起； 打开
“ 导轨夹紧
”
开关， 单击
“ CCD 回位
”
， 将 CCD Ca mera
回到原点位置；打开 [Z 轴上升 ] 将 PCB 板升到紧贴钢网板底面位置；
4) Then switch off “ Transport switch ” and switch on “ PCB board absorbing valve ”
at
the
same time; stop “ Board stop cylinder ” , switch on “ Platform crest slab ” switch to make the
workbench rise; switch on “ Guide rail clamping ” switch and click “ CCD return ” to restore
CCD Camera to the initial position; and open “ axis Z rise ” to make PCB board rise and firmly
lean on the bottom of screen;
5) 用眼睛观察网板与 PCB 板对准情况， 并用手移动调节网框、 定位夹紧装置使之与 P CB
板对准。
5) Visually observe the alignment condition of screen and PCB board and adjust the screen
frame and positioning and clamping devices with hand to make them align with PCB board;
6) 打开 “ 网框固定阀 ” 和 “ 网框夹紧阀
”
，将网框固定并夹紧；同时将机器上的网框 锁
深圳德森精密设备有限公司
Shenzhen Desen Precision Machine Co., Ltd.
- 24 -
紧气缸用挡环固定及移动 Y 向定位挡住网框；
6) Switch on “ Screen frame standing valve ” and “ Screen frame clamping valve ” to fix and
clamp the screen frame. A
t
the same time, fix the screen frame locking cylinder on the
machine firmly with a limit ring and cover the screen frame by moving the positioning device
of axis
Y;
7) 关闭 “ Z 轴上升
”
，使工作台回到取象位置；
7) Switch off “ Axis Z rise ” to make the workbench return to the image taking position; and
8) 单击 “ 标志点设置
”
，进入 “ 标志点采集 ” 对话框。
8) Click “ S ignalized point setting ” to enter the “ Signalized point collect ” dialog box .
8.
在 “ 标志点采集 ” 对话框中，进入标志点采集和 PCB 校正，完成 PCB 与网板位置视
觉校正并对准。
8. In the “ Signalized point collect ” dialog box , enter signalized point collection and PCB
calibration to finish the visual calibration and alignment of the positions of PCB board and screen;
9.
在 标志点设置 完后，单击 “ 标志点设置 ” 对话框中的 [ 确认 ] ，回到生产编辑窗口。
9. After the signalized point setting is done, click Enter in the “ S ignalized point setting ” dialog box
to return to the production editing window; and
10.
单击主工具栏中的 “ 文件 / 保存
”
，将此次 PCB 板的参数设置保存到新建的文件名下，
待开始生产时打开此档使用。
10. Click “ File/Save ” in the main tool bar to save the parameter setting of PCB board this time to a
newly created file which shall be opened for use after production is started.
注： 以上操作说明详见第四章介绍。
Note:
Note:
Note:
Note:
see
see
see
see
Chapter
Chapter
Chapter
Chapter
IV
IV
IV
IV
for
for
for
for
detailed
detailed
detailed
detailed
introduction
introduction
introduction
introduction
of
of
of
of
the
the
the
the
operations
operations
operations
operations
above.
above.
above.
above.
3.2.4
3.2.4
3.2.4
3.2.4
刮刀的安装
3.2.4
3.2.4
3.2.4
3.2.4
Installation
Installation
Installation
Installation
of
of
of
of
squeegee
squeegee
squeegee
squeegee
11.
打开机器前盖；
1. Open the front cover of machine;
12.
移动刮刀横梁到适合位置，将装有刮刀片的刮刀压板装到刮刀头上；
2. Move the squeegee beam to an appropriate position and install the squeegee pressure plate with
a squeegee blade to the squeegee head;
13.
刮刀行程的调整：打开工具栏 1 中 [ 参数设置 ] ，输入二级密码 ” printer9 ” 打开 [ 参数设置 ]
对话框，进行刮刀升降行程的设置；