德森印刷机说明书之操作手册-4d1321fc284ac850ac024234.pdf - 第28页
深圳德森精密设备有限公司 Shenzhen Desen Pre cision Machine Co., Ltd. - 28 - such a s c l eaning m anner o r c le aning time inter val. 3.4 3.4 3.4 3.4 生产流 程 3.4 3.4 3.4 3.4 P r oduction P r oduction P r oduction P r oduction flow fl…
深圳德森精密设备有限公司
Shenzhen Desen Precision Machine Co., Ltd.
- 27 -
0.5 ～ 2mm . The setting scope of demoulding length allowed by this printing machine is 0 ～ 10mm .
3.3
3.3
3.3
3.3
试生产
3.3
3.3
3.3
3.3
Trial
Trial
Trial
Trial
production
production
production
production
在以上准备工作做完以后，即可进行 PCB 板的试印刷。操作方法是：
Trial printing of PCB board can be practiced after the completion of the preparations above.
F ollowing are the operation method:
1.
单击主工具栏中的 [ 开始生产 ] 按钮并按照操作接口上对话框的提示进行操作， 完成一 块
PCB 板的自动印刷（详见第四章主工具栏的操作说明） 。
1. Click Start Production in the main tool bar and operate following the prompts in the dialog box
of operation interface to finish the automatic printing of a PCB board (see the operating
instructions in the main tool bar of Chapter IV for more details);
2.
如检测结果不符合质量要求，应重新进行编辑或输入印刷误差补偿值（详见第四章
4.4.14 “ 生产设置 ” 对话框；如检查结果满足质量要求，即可正式开始生产。
2. In the event that the inspection result dose not conform to the quality requirement,
it
is necessary
to edit or input the printing error compensation value again (see the dialog box of 4.4.14
“ Production Setting ” in Chapter IV); and in the event that the inspection result meets the quality
requirement, production can be started formally;
3.
锡膏印刷质量要求：
本机器设定锡膏厚度在 0.1 — 0.3mm 之间、 焊膏覆盖焊盘的面积在 75% 以上即满足质 量
要求。
3. Quality requirement for solder paste printing:
According to the settings, the printing machine
’
s
quality requirement can be met when the
solder paste thickness is during 0.1 — 0.3mm and the area of bonding pad covered by solder
paste is above 75%; and
4.
网板清洗品质检测：
本机器设定锡膏堵塞网板的覆盖面积超过 20% 会有报警提示，此时可单击主工具栏
中 [ 网板清洗 ] ，重新设置清洗方式或清洗的时间间隔等参数。
4. Quality inspection for the cleaning of screen:
As set, the printing machine will give alarm when the covered area of solder paste on the
screen is larger than 20%, click the Screen Cleaning in the main tool bar to reset parameters
深圳德森精密设备有限公司
Shenzhen Desen Precision Machine Co., Ltd.
- 28 -
such as cleaning manner or cleaning time interval.
3.4
3.4
3.4
3.4
生产流程
3.4
3.4
3.4
3.4
Production
Production
Production
Production
flow
flow
flow
flow
开启总电源开关
打开气源开关
打开机器主电源开关
进入机器主画面
机器归零
新建文件
生产编辑
打开已有文件
钢网定位
保存檔
PCB 进板
开始生产
PCB 到位
视觉校正
印刷焊膏
网板清洗
停止生产
退出主画面
关闭主电源开关
继
续
生
产
关闭气源开关
关闭总电源开关
深圳德森精密设备有限公司
Shenzhen Desen Precision Machine Co., Ltd.
- 29 -
Open the general power switch
Open the air supply switch
Open machine
’
s main power s witch
Enter the main interface of machine
Return to zero
Create a new file
Production Edit
Open a file
Steel mesh locate
Save a file
PCB board incoming
Start production
PCB board is in place
Visual calibration
S o lder paste for painting
Steel mesh cleaning
Stop production
Exit the main interface
Close the main power switch
Conti
nue
with
produ
ction
Close the air supply switch
Close the general power switch