00195166-0402_SM_D4_EN.pdf - 第101页
Service W ork Cutter Component Handling Service Manual SIPLACE D4 101 4.3.2.8 Replacing the Articulated Joint on the Sho rt-Stroke Cylinder [00348579-xx] Removing the articulated joint and short-stroke cy linder X Remove…
Service Work
Component Handling Cutter
100 Service Manual SIPLACE D4
See also:
J
4.3.2.7 Replacing the Stationary Blade and Movable Blade incl. Spacers [
J
95]
J
Tightening Torques for Cutter Screws [
J
87]
J
6.4.3 Check the gap between the empty-tape baffle, inside and the leading edge of the tape deflector.
[
J
241]
J
4.3.2.14 Final Steps [
J
114]
X Make certain that the edges are parallel, then
screw the cover plate holder to the cutter (two
M4 screws each (7, 9)):
-> Do not pinch or put strain on the cables.
X Install the cover plate on the stationary blade
(4 M4 screws (12, 13)).
X Remove the parallel clamps from the cutter or
dismantle the cutter from the mounting plate.
X Fit the cutter back into the machine. (See sec-
tion (4.3.2.5 Exchanging the Pneumatic Cutter
J
87 ) .)
X Fit the empty-tape duct assembly and check
the gap between the empty-tape baffle, inside
and the leading edge of the tape deflector.
X Perform the appropriate “Final Steps”.
Service Work
Cutter Component Handling
Service Manual SIPLACE D4
101
4.3.2.8 Replacing the Articulated Joint on the Short-Stroke Cylinder [00348579-xx]
Removing the articulated joint and short-stroke cylinder
X Remove the cutter from the machine. (See section (4.3.2.5 Exchanging the Pneumatic Cutter
J
87
) .)
X Remove the deflector plate from the cutter.
X Loosen the screws holding the moveable blade.
4-34: Compressed air connections, left (1) and right (2)
X Loosen the compressed air connections (1, 2) on the short-stroke cylinder.
X In addition, mark the allocation of the proximity switches to the short-stroke cylinder (position front/
back).
4-33: Replacing the articulated joint on the short-stroke cylinder
WARNING: Risk of injury!
Wear appropriately thick protective
gloves!
There is a high risk of injury from the
blades and the tape deflector.
Never reach into the cutter from below
or into the empty-tape duct from above.
Legend
1. Deflector plate
2. Cover
3. Screws to fasten short-stroke cylinder
4. Articulated joint
5. Screws to fasten the moveable blade
Service Work
Component Handling Cutter
102 Service Manual SIPLACE D4
4-35: Removing and Installing the Short-Stroke Cylinder
Legend
X Loosen the screws fastening the two inductive proximity switches to the short-stroke cylinder (1
screw each (4, 5)).
X Loosen the screws fastening the short-stroke cylinder (1) (2 M5x65 screws (5)) and remove the
cylinder, incl. the articulated joint screwed into it.
1 Short-stroke cylinders 1 and 2 6 One-way restrictor (for running cylinder out)
2 Screws fastening the short-stroke cylinders: 2 M
5x65 hexagon socket-head screws each
7 One-way restrictor (for running cylinder in)
3 Articulated joint fixtures 8 Allocation of the compressed air connections,
pneumatic hoses
4 Proximity switch (for position cylinder moved in).
Fastener: 1 Phillips screw 9 Y-socket union (in the cable duct)
5 Proximity switch (for position cylinder moved
out). Fastener: 1 Phillips screw
10 Multiple-Y-distributor on the safety valve (5 bar
from compressed air unit)