00195166-0402_SM_D4_EN.pdf - 第261页
Settings Conveyor Control TSP 301 Conveyor Service Manual SIPLACE D4 261 6.5.12.2 Conveyor Control TSP 301 with Siemens Interface 6-45: TSP 301 SMEMA --> Siemens NOTE: Standar d / Option The SMEMA interf ace is a st a…
Settings
Conveyor Conveyor Control TSP 301
260 Service Manual SIPLACE D4
*Switches 1-2 set the hardware ID 5 for D4 machines and hardware ID 6 for X machines, HF and D3.
6-44: Jumper J1, J2 "downstream/upstream station" at TSP 301
Legend
J1 predecessor station
J2 successor station
J3 interference loop (emergency stop on
productivity lift switches the placement
machine off)
J6 CAN bus 2 terminating resistor (not used)
J7 CAN bus 1 terminating resistor
S X4I D4 X/D3/HF Comments
1ON ON ONON*
2OFF ON OFF ON* = SIPLACE D4, OFF: SIPLACE X, HF, D3
3OFF OFF OFF OFF= clamping sensor is no longer used
4ONOFFOFFON = X4I, OFF: SIPLACE D4, X, HF, D3
5OFF OFF OFF Not in use
6OFF OFF OFF Not in use
7OFF OFF OFF Not in use
8OFF OFF OFF Not in use
Settings
Conveyor Control TSP 301 Conveyor
Service Manual SIPLACE D4
261
6.5.12.2 Conveyor Control TSP 301 with Siemens Interface
6-45: TSP 301 SMEMA --> Siemens
NOTE: Standard / Option
The SMEMA interface is a standard on
all X machines and the Siemens
interface is optional.
The Siemens interface is a standard on
all D machines and the SMEMA
interface is optional. The SMEMA
interface requires an adapter when
used with the D1/2/4.
WARNING: Risk of irreparable
damage to the TSP board!
The 10 pin Locking clip plug of SMEMA
connections must be disconnected
from the TSP 301!
Application: no modification.
Following modification are necessary for using the
Siemens interface:
X JumperJ1 / J2: need to be moved (see
following diagram).
X Disconnect the connector X3 and X4 on the
TSP 301!
X Connect the Siemens interface cable on the
connector X1 and X2.
Legend
1. 10-pin plug for SMEMA interface
X3: upstream station
X4: successor station
2. Connection for Siemens interface
X1: upstream station
X2: successor station
6-46: Jumper J1 and J2 (Siemens/SMEMA)
Settings
Conveyor Conveyor Control TSP 301
262 Service Manual SIPLACE D4
6.5.12.3 LED Display on Conveyor Control TSP 301
6.5.12.4 Assignment Table: LEDs on the TSP 301 Conveyor Control
6-47: Conveyor Control TSP 301
Legend
1. Connector for Siemens PCB handling
interface of predecessor station, lane 1 with
corresponding PCB handling LEDs
2. Connector for Siemens PCB handling
interface of successor station, lane 1 with
corresponding PCB handling LEDs
The "Siemens board handling interface for the
predecessor station of lane 2 with corresponding
LEDs for board handling" plug and the "board
handling interface for the successor station of lane
2 with corresponding LEDs for board handling"
plug are located on the extension board (similar
layout).
Anzeige
/Display
I / O LED assignment
H1 / F1-F5 Fuse F1-F5, Power supply 40 V
H2 / F6 Fuse F6 Power supply 24V
H4(ao) Initializing / control error
H5(ao) CAN bus 1, active
H6(ao) Flashing: Program running
H7(ao) CAN bus 2, active (optional)
H9 Out Interference loop
H14 IN Siemens interface for upstream station
H15 IN Siemens interface for downstream station
H20 IN Lifting table, placement area 1: Fork light barrier A
H21 IN Lifting table, placement area 1: Fork light barrier B
H22 IN Lifting table, placement area 2: Fork light barrier A