00197501-02_AI_WPC_Umbau_X-Series_S_DE_EN.pdf - 第90页
Review 5 Appendix 5.1 Excerpts from the Service Manual 90 Assembly Instructions / Montageanleitung SIPLACE WPC an SIPLACE X-Serie S SIPLACE WPC on SIPLACE X Series S 03/2020 Fig.53: Magazine 20xx [03135469-xx] Magazine …
Review
5 Appendix
5.1 Excerpts from the Service Manual
Assembly Instructions / Montageanleitung SIPLACE WPC an SIPLACE X-Serie S SIPLACE WPC on SIPLACE X
Series S 03/2020
89
Description of CAN node NC tape cutter module
This board is backwards compatible to the old tape cutter board. It can be used at X, HF and D
series machines.
The CAN processor decides which functions need to be checked at the individual locations, de-
pending on the cables connected and the type of DIP switched set.
DIP switch group S3 - overview
DIP
switch
DIP switch meaning
1 ON: Setting the CAN ID via DIP switch 2 and 3 – OFF: Cable Select
2 CAN -ID 0 ON: Gantry 1
1)
ON
OFF: Gantry 2
1)
ON
ON: Gantry 3
1)
OFF
OFF: Gantry 4
1)
OFF: Cable select
3 CAN - ID 1
4 ON: Only tape cutter – OFF: Nozzle changer and tape cutter
2)
5 ON: Module in reset-mode – OFF: Module in standard mode
1)
Not all gantries may be available, depending on the machine type.
2)
Even if there is no nozzle changer installed and only the tape cutter needs to be controlled, this
switch still needs to be set to OFF for the reject bin query and the reject station.
X series machine with CAN node
The cable of the machine (cable harness machine) has to be by-passed as shown in the list:
*112: Gantry 1: 10/11/12 by-passed
*122: Gantry 2: 11/12 by-passed
*132: Gantry 3: 10/12 by-passed
*142: Gantry 4: not by-passed
5.1.3 Nozzle Changers and Nozzle Stations - Overview
Fig.50: Nozzle changer short [03103649‑xx]
Standard nozzle changer, short
[03103649‑xx] for four magazines
Fig.51: Nozzle changer, long [03147324‑xx]
Standard nozzle changer, long
[03147324‑xx] for six magazines
Fig.52: Nozzle changer, long
Nozzle changer, long
for SIPLACE C&P20 [03070123‑xx]
for SIPLACE C&P20M [03147324‑xx]
with six magazines [00119715‑xx]
Review
5 Appendix
5.1 Excerpts from the Service Manual
90 Assembly Instructions / Montageanleitung SIPLACE WPC an SIPLACE X-Serie S SIPLACE WPC on SIPLACE X
Series S 03/2020
Fig.53: Magazine 20xx [03135469-xx]
Magazine for 20 nozzles of 20xx series
With two fiducials [03135469‑xx]
With three fiducials [03226630‑xx]
Fig.54: Magazine 28xx [03065782-xx]
Magazine for nozzles of 28 xx series
Fig.55: 40xx/60xx magazine [03101503-xx]
Magazine for nozzles of 40xx/60xx series
With two fiducials [03101503‑xx]
With three fiducials [03218226‑xx]
Fig.56: Nozzle changer TwinStar (short) [03062452‑xx]
1. Nozzle changer TwinStar (short)
[03062452‑xx]
2. Magazine for 1 nozzle [03001807-xx]
3. Magazine for 2 nozzles [03005191-xx]
4. Nozzle changer in standard configura-
tion
1x magazine for 1 nozzle
3x magazine for 2 nozzles
Review
5 Appendix
5.2 Circuit Diagrams
Assembly Instructions / Montageanleitung SIPLACE WPC an SIPLACE X-Serie S SIPLACE WPC on SIPLACE X
Series S 03/2020
91
5.1.4 Dismantling the Lower Side Cover
Most tasks require that you dismantle the lower side cover from the location. This is shown below
using the example of location 2. The procedure for other locations is identical. The procedure is the
same for other locations.
Parts, equipment and tools
●
Shortened Allen key, if required
Dismantling the side cover
Fig.57: Dismantling the lower side cover
► While unscrewing, always hold on to
the side cover, to prevent it falling off.
► Remove the six screws(1) fastening
the inner(A)
and outer side(B) of the
side panel.
NOTICE!
The three fastening screws (2) on the
outer side are loosened as a default.
The side cover can be pulled out here.
.
► Remove the side cover.
Fitting the side cover
► Assembly is performed by following the above instructions in the reverse order.
5.2 Circuit Diagrams
For more information, refer to the circuit diagrams folder:
●
Detailed circuit diagrams folder for SIPLACE X-Series S (up to Gxxxx) [DE+EN:00197021‑xx]
●
Detailed circuit diagrams folder for SIPLACE X-Series S (from Hxxxx) [DE+EN:00197920‑xx]