00197975-06_UM_TX-Serie_EN.pdf - 第237页
User manual SIPLACE TX-Series 5 Tasks at the placement machine From software version 713.0 Edition 01/2020 5.5 The user interfac e 237 5.5.4 Operating the st ation sof t ware in the views Most views which can be accessed…
5 Tasks at the placement machine User manual SIPLACE TX-Series
5.5 The user interface From software version 713.0 Edition 01/2020
236
5.5.3 Toolbar
The toolbar contains buttons for the main station software functions.
These enable you to switch the user interface over to other views and to use the functions avail-
able there (see section 5.5.5
, page 240).
5
Fig. 5.5 - 2 Toolbar
The buttons vary according to your individual configuration and the operator level set. Some views
are only available in higher operator levels.
The following table briefly describes the buttons and main functions.
5
Icon View Description
Production
(main view)
Shows the placement machine status for the most frequently
performed tasks during production.
Shows the operating states, see section 5.5.2
, page 235.
Shows locations, name of setup, name of recipe, configuration
changes and additional options.
Feeder modules,
components and
nozzles
The setup can be individually opened for each of the 4 locations.
Allows you to check and configure feeder modules, components
and nozzles.
Allows you to teach component shapes and component pocket
shapes.
Shows the component level indicator.
Filling level view During placement, the operator is shown at all times when the
individual feeders will run empty and need to be filled up again.
PCBs Shows the boards and placement positions list.
Allows you to check and configure boards and components.
Allows you to teach fiducials.
Notifications Shows notifications about current and previous events. The notifi-
cations vary according to their type. Individual tables can be viewed
for track errors, conveyor errors, placement machine errors, gen-
eral errors and linked error messages (see section 5.6
, page 242).
Statistics Shows the statistics for performance, quality and rejected material.
Shows the placement machine and board performance.
Starts the OIS (Operator Information System), for more information
refer to the OIS documentation.
User manual SIPLACE TX-Series 5 Tasks at the placement machine
From software version 713.0 Edition 01/2020 5.5 The user interface
237
5.5.4 Operating the station software in the views
Most views which can be accessed via the toolbar (see section 5.5.3, page 236) have an addi-
tional vertical toolbar with subviews and functions, on the right-hand side of the user interface.
5
Example: View: "Feeder modules, components and nozzles"
Click on "Feeder modules, components and nozzles" in the toolbar.
The following view will open:
Live image during
placement
Shows the individual live camera images.
Only available from operator level "Advanced Production" :
Allows you to view and save the Vision dump.
Settings Contains all the settings and options.
Allows you to set the operator level and the user interface language.
Allows you to display and edit the settings, user settings, placement
machine options and software options, see section 5.5.5
, page 240.
Check sensors
and functions
Contains information and functions for tests and diagnoses.
Allows you to set the function of the start button for the placement
machine.
Only available from operator level "Advanced Production" :
Allows you to test the complete reference run and C&P20 head
functions.
Single functions and continuous runs. Each gantry is addressed
individually.
Maintenance sta-
tus
Contains information about the maintenance status for the place-
ment machine.
For more information, read the maintenance manual.
Service Service tools.
Only available from operator level "Service (customer)".
Allows you to set up and calibrate the SIPLACE placement ma-
chines, download embedded software versions, calibrate and con-
figure the entire placement machine.
Icon View Description
PLEASE NOTE
For a detailed description of the individual functions refer to the Online Help.
5 Tasks at the placement machine User manual SIPLACE TX-Series
5.5 The user interface From software version 713.0 Edition 01/2020
238
5
Fig. 5.5 - 3 User interface in the "Feeder module, components and nozzles" view (example)
Legend
(1) Toolbar ("Feeder modules, components and nozzles" button)
(2) Vertical toolbar in "Feeder modules, components and nozzles" view
(3) Button for both conveyor lanes
(4) Button for table at location 1
Click, for example, on the table at location 1 (button 4), to check the configuration.
(1)
(2)
(3)
(4)