4OM-1075-002.pdf - 第131页
Error ID Item Description 080201 Head Rotational #1Axis Timing T ask has not been completed unable to continue. (Cause 1) Self-Diagnostics Error Message (Remedy 1) Zero all axes and re-start the operation. When the machi…
Error ID Item Description
080101 Head Rotational #1Axis Origin Encoder origin was not detected.
080102 Head Rotational #1Axis Origin Origin sensor (slide) was not detected.
080103 Head Rotational #1Axis Origin Origin sensor (slide) and Limit error has been de-
tected.
080104 Head Rotational #1Axis Origin Feedback value is indefinite.
080105 Head Rotational #1Axis Origin Z1 axis is not at origin.
(Cause 1) Self-Diagnostics Error Message
(Remedy 1) Zero all axes and re-start the operation.
When the machine cannot be set to its normal condition, consult our service
personnel for the remedy.
3.3 Error IDs and Remedial Procedures
0308-001 2-41-1 AHB01ETRP
Error ID Item Description
080201 Head Rotational #1Axis Timing Task has not been completed unable to continue.
(Cause 1) Self-Diagnostics Error Message
(Remedy 1) Zero all axes and re-start the operation.
When the machine cannot be set to its normal condition, consult our service
personnel for the remedy.
080301 Head Rotational #1Axis Data The driver data was detected outside of the possible
range.
(Cause 1) Self-Diagnostics Error Message
(Remedy 1) Zero all axes and re-start the operation.
When the machine cannot be set to its normal condition, consult our service
personnel for the remedy.
080401 Head Rotational #1Axis Limit (+) Limit error has been detected.
080402 Head Rotational #1Axis Limit (-) Limit error has been detected.
(Cause 1) The X1 axis might have overrun due to generation of noises, overcurrent, etc.
The sensor may be defective.
(Remedy 1) Zero all axes and re-start the operation.
When the machine cannot be set to its normal condition, consult our service
personnel for the remedy.
080502 Head Rotational #1Axis Servo Alarm Parameter breakdown.
080503 Head Rotational #1Axis Servo Alarm Main circuit encoder error.
080504 Head Rotational #1Axis Servo Alarm Parameter setting error.
080505 Head Rotational #1Axis Servo Alarm Combination error.
080510 Head Rotational #1Axis Servo Alarm Overcurrent or heat sink overheated.
(Cause 1) Self-Diagnostics Error Message
(Remedy 1) Zero all axes and re-start the operation.
When the machine cannot be set to its normal condition, consult our service
personnel for the remedy.
3.3 Error IDs and Remedial Procedures
0107-001 2-42 AHB01ETRP
Error ID Item Description
080530 Head Rotational #1Axis Servo Alarm Regenaration error detected.
080532 Head Rotational #1Axis Servo Alarm Regenarative overload.
080540 Head Rotational #1Axis Servo Alarm Overvoltage.
080541 Head Rotational #1Axis Servo Alarm Undervoltage.
080551 Head Rotational #1Axis Servo Alarm Overspeed.
080571 Head Rotational #1Axis Servo Alarm Overload: High load.
080572 Head Rotational #1Axis Servo Alarm Overload: Low load.
080573 Head Rotational #1Axis Servo Alarm Dynamic brake overload.
080574 Head Rotational #1Axis Servo Alarm Overload of surge current limit resistor.
08057a Head Rotational #1Axis Servo Alarm Heat sink overheated.
080581 Head Rotational #1Axis Servo Alarm Encoder backup error.
080582 Head Rotational #1Axis Servo Alarm Encoder checksum error.
080583 Head Rotational #1Axis Servo Alarm Absolute encoder battery error.
080584 Head Rotational #1Axis Servo Alarm Encoder data error.
080585 Head Rotational #1Axis Servo Alarm Encoder overspeed
080586 Head Rotational #1Axis Servo Alarm Encoder overheated.
080591 Head Rotational #1Axis Servo Alarm Overload warning.
080592 Head Rotational #1Axis Servo Alarm Regenerative overload warning.
080594 Head Rotational #1Axis Servo Alarm Setting warning.
080595 Head Rotational #1Axis Servo Alarm Command warning.
(Cause 1) Self-Diagnostics Error Message
(Remedy 1) Zero all axes and re-start the operation.
When the machine cannot be set to its normal condition, consult our service
personnel for the remedy.
3.3 Error IDs and Remedial Procedures
0107-001 2-43 AHB01ETRP