4OM-996-007.pdf - 第332页

3.3.3 T eaching Errors (60 Nozzle Position) Error ID ltem Description 600101 Nozzle Recog. Recognition Error Code. Ref.: Refer to “4.3.4 Nozzle Recognition Errors" for the detailed error display . 600201 Nozzle Bypa…

100%1 / 417
Error ID ltem Description
500b01 Cancel Recovery On Collect component if necessary.
500b02 Cancel Recovery On Pick-up Sequence Cancel.
Collect component if necessary.
500b03 Cancel Recovery On Component Output was check sequence mode.
Collect component if necessary.
500b04 Cancel Recovery On Nozzle Down Error(Low).
Collect component if necessary.
500b05 Cancel Recovery On Nozzle Down Error(High).
Collect component if necessary.
500b06 Cancel Recovery On Selected Nozzle Position Error.
Collect component if necessary.
500b07 Cancel Recovery On Unselected Nozzle Drop.
Collect component if necessary.
500b08 Cancel Recovery On Cam Positon Return Error.
Collect component if necessary.
500b09 Cancel Recovery On Nozzle Change Error.
Collect component if necessary.
500b0a Cancel Recovery On The nozzle change lever was not activated.
Collect component if necessary.
500b0b Cancel Recovery On The nozzle change/return lever was not activated.
Collect component if necessary.
500b0c Cancel Recovery On Pick-up Y-position Error.
Collect component if necessary.
500b0d Cancel Recovery On Pick-up Error.
Collect component if necessary.
500b0e Cancel Recovery On The selected nozzle was not at position. ;Nozzle posture
detection. Collect component if necessary.
500b0f Cancel Recovery On Component backtrack or Component output is detected.
;Nozzle posture detection. Collect component if necessary.
(Cause 1) Self-Diagnostics Error Message
(Remedy 1) Zero all axes and re-start the operation.
When the machine cannot be set to its normal condition, consult our service
personnel for the remedy.
500c01 Auto Recovery Pause "Attach the new comp. And press [READY].
Then, press [START] button to re-start."
(Cause 1) Self-Diagnostics Error Message
(Remedy 1) Zero all axes and re-start the operation.
When the machine cannot be set to its normal condition, consult our service
personnel for the remedy.
0509-003 2-135 AIM01ETRP
3.3 Error IDs and Remedial Procedures
3.3.3 Teaching Errors
(60 Nozzle Position)
Error ID ltem Description
600101 Nozzle Recog. Recognition Error Code.
Ref.: Refer to “4.3.4 Nozzle Recognition Errors" for the detailed error display.
600201 Nozzle Bypass Nozzle Down Error. (L)
600202 Nozzle Bypass Nozzle Down Error. (H)
600203 Nozzle Bypass Recognition Teach Error.
(Cause 1) When the selected nozzle reached the L or H level during operation, the optical
beam of the sensor was shielded (not received).
The sensor may be defective.
(Remedy 1) Remove the dirt on the nozzle end and insert the nozzle deep inside.
The sensor may be defective. If necessary, replace the sensor with a new one.
Before replacing the sensor, contact our service personnel for some advice.
600204 Nozzle Bypass Teach Error Data.
(Cause 1) Dirt and dust adhere to the nozzle and an error is found in the nozzle teaching
operation.
(Remedy 1) Remove dirt and dust from the nozzle end and re-perform the nozzle teaching
operation.
600205 Nozzle Bypass Lighting Check.
(Cause 1) The diffusion plate of the nozzle may be dusty and dirty or scratched.
(Remedy 1) Clean the diffusion plate or replace it with a new one.
0509-003 2-136 AIM01ETRP
3.3 Error IDs and Remedial Procedures
Error ID ltem Description
600206 Nozzle Bypass Nozzle Level
(Cause 1) The nozzle being used has dropped.
(Remedy 1) Check the pertinent nozzle.
When the machine cannot be set to its normal condition, consult our service
personnel for the remedy.
600207 Nozzle Bypass Nozzle Drop
(Cause 1) The nozzle being used has dropped.
(Remedy 1) Check the pertinent nozzle.
When the machine cannot be set to its normal condition, consult our service
personnel for the remedy.
600208 Nozzle Bypass Dummy Nozzle
600209 Nozzle Bypass Manual Bypass
(Cause 1) This appears when some nozzles are bypassed manually.
(Remedy 1) When the [Reset Noz. Bypass] button is pressed in the "Head/Noz. Bypass" tab
sheet of the "OPN. MODE" window (submenu), the manual bypass designation of
all nozzles is all canceled.
60020a Nozzle Bypass Nozzle Change Error. (Cam lock action)
60020b Nozzle Bypass Nozzle Change Error. (Cam Free action)
60020c Nozzle Bypass Cam Origin Error.
60020d Nozzle Bypass Nozzle Teach Error.
60020e Nozzle Bypass Nozzle Posture Detection
(Cause 1) Self-Diagnostics Error Message
(Remedy 1) Zero all axes and re-start the operation.
When the machine cannot be set to its normal condition, consult our service
personnel for the remedy.
0509-003 2-137 AIM01ETRP
3.3 Error IDs and Remedial Procedures