4OM-996-007.pdf - 第86页

1.3 Maintenance Spots Fig. 4A26 0509-002 1-23 AIM01ETRP Cooling Oil Filter 2Y1 Every 2 Y ears Oil Filter Replacement The oil filter must be replaced with a new one after initial 500 hours and every 12,000 hours for the s…

(11) Main Body Driving Section

1.3 Maintenance Spots

Fig. 4A25

0509-003 1-22

AIM01ETRP

Lubrication for Rotary Turret 1Y2

Every Year Oil Change (SYNTHESO HT220)

Pull out the oil outlet hose from the machine and discharge the old oil into the

container. After that, supply new oil from Oil Inlet 1 or 2.

Note: Do not apply any air pressure to the internal area of the rotary turret

while oil is being discharged.

Otherwise, oil may leak out of the sealed section of the rotary turret.

• Change the oil with new one after initial 500 hours and every 6,000 hours for

subsequent use.

The proper amount of oil is equivalent to "1/2" of the oil gauge. (11 or 12 liters)

• Wipe off the oil pooled in the oil pan if necessary.

Precautions on Oil Replenishment

After the oil supply, turn on the power to activate the oil cooling pump.

After the machine is powered up, turn off the power of the machine (normal

shutdown operation).

Check the amount of oil when the oil level has become stable.

Note: Refer to "1.4.13 Lubrication of Rotary Turret" for the lubrication

procedure.

Oil Gauge of Rotary Turret 1W9

Every Week Inspection

Check the level of the oil gauge with the machine not powered.

If the level is not located at the center (red ball) of the oil gauge, replenish the oil.

• The proper amount of oil is equivalent to "1/2" of the oil gauge.

Rotary Turret

Oil Outlet

Cooling Oil Filter

Oil Inlet 1

Oil Inlet 2

1.3 Maintenance Spots

Fig. 4A26

0509-002 1-23

AIM01ETRP

Cooling Oil Filter 2Y1

Every 2 Years Oil Filter Replacement

The oil filter must be replaced with a new one after initial 500

hours and every 12,000 hours for the subsequent use.

The new oil filter is attached as an accessory.

Note: Refer to "1.4.12 Replacement of Oil Filter" and "1.4.13

Lubrication of Rotary Turret" for how to replace the oil

filter.

Cooling Oil Filter

Nut

Cover

1.3 Maintenance Spots

(12) Cutter Section

Fig. 4A27

0509-004 1-24

AIM01ETRP

Spring 1M9-1

Every Month Lubrication

(MOLYNOC GREASE AP1)

Apply the grease to the springs by hand

or using a brush.

Upper and Lower Blades 1M7

Every Month Inspection

Check how the tape is cut. When the cutting quality

has deteriorated, replace the blades with new ones.

Note: Refer to "1.4.8 Replacement of Cutter Blade"

for the replacement.

Outer Circumference of Rod End 1M8

Every Month Lubrication

(MOLYNOC GREASE AP1)

Inject grease from the oil inlet with a

dispense gun.

* Use No.19 (brown) nozzle.

Rod End 1M9

Every Month Lubrication

(DAPHNE EPONEX GREASE No. 1)

Set the timing angle of the rotary turret to approx. 265

degrees and inject grease from the grease nipple with a

grease gun.

* Use the U- and V-type attachments.

U Type

V Type

Backup Plate 1M10

Every Month Lubrication

(MOLYNOC GREASE AP1)

Apply grease to the sliding surface of

the cutter lower blade with a brush.

Surface of Lower Blade 1M11

Every Month Lubrication

(MOLYNOC GREASE AP1)

Detach the cutter cover and apply

grease to the surface of the cutter lower

blade by hand or using a brush.

No.19