YC8_Mainte_E.pdf - 第7页
v Safety instructions n Muzzle plate Use these plates as a safety measure for the board convey or entrance and exit openings. Each plate is mo vable, so adjust the mounting position to match the boards to be produced. Mu…
iv
Safety instructions
1.8 Keeping hands away from moving parts
During use of this machine, the customer’s equipment and operating conditions might allow the operator’s
hands to come into contact with moving parts.
Use the following safety measure options to avoid possible danger where openings or gaps are found on the
machine.
n
Dummy feeder
Use dummy feeders as safety measures to fill a gap between tape feeders. Install dummy feeders on the feeder plate the
same way as normal feeders in order to prevent hands from entering.
Prevention of hand entry
Dummy feeder
Dummy feeder (Wide-size)
Dummy feeder (8mm-size)
Clamp lever
YS series YG series
91203-L0-10
c
machine has a structure that does not allow installing or removing a dummy feeder when the machine is in operation.
to attempt it.
n
One-stop cover (For feeder exchange carriage)
If not using a feeder exchange carriage in the machine that is to be used with feeder exchange carriages, install a
one-stop cover in the position where a feeder exchange carriage is to be installed.
Prevention of hand entry
One-stop cover
One-stop cover
91204-L10-10
n
NOTE
One-stop covers cannot be installed or removed during operation. The machine must be in a stopped state because
the section where a feeder exchange carriage is to be installed will move up and down for the installation or removal
of the feeder exchange carriage.
v
Safety instructions
n
Muzzle plate
Use these plates as a safety measure for the board conveyor entrance and exit openings. Each plate is movable, so adjust
the mounting position to match the boards to be produced.
Muzzle plate
Upper muzzle plate
Lower muzzle plate
Board conveyance plane
91205-L0-00
Upper clearance Lower clearance Remarks
YS100/YS88 8.0 to 38.5mm 1.0 to 31.0mm
From board conveyor plane
YS12, YS12P, YS12F, YS24, YS24X 5.0 to 20.0mm 4.2 to 39.2mm
YC8 13.4 to 80.4mm 4.6 to 39.2mm
YSP 0 to 6.6mm 0 to 26.4mm
vi
Safety instructions
1.9 Handling solvents
Take the following precautions when handling cleaning solvents during solder printing or preparation.
Hazards when handling solvents
1. Hazards to human health
Organic solvents constantly vaporize and contaminate the surrounding atmosphere. Inhaling or coming in contact with
organic solvent vapor may cause serious damage to human health.
2. Flammability
Organic solvents are highly flammable substances and can easily catch fire if handled improperly.
3. Adverse effects on machines
Some solvent types will damage the cleaning unit, electrical wire sheath and various units used in the solder paste
printer.
To avoid hazards of solvents
1. Be careful not to inhale toxic vapors of solvents for extended periods.
2. Do not use solvents near fire or flame. Keep solvents away from flame or fire.
3. Use only the specified solvent in the correct manner. Do not reuse any solvent repeatedly, and do not mix with other
solvents or chemicals.
1.10 Handling the X-ray unit
Some YS series inspection equipment models contain an X-ray unit. Take the following precautions when using
with an X-ray unit.
1. The X-ray output window of the X-ray source is made of very thin beryllium foil.
· Beryllium in the form of dust particles can cause acute toxicity or chronic toxicity, and may induce respiratory
problems if inhaled.
· To ensure safety, the X-ray unit is designed so that the X-ray window cannot be touched. However, should the X-ray
output window be broken for some reason, immediately turn off the power switch and use extreme care not to inhale
the dust particles.
· Chlorine gas can corrode the beryllium window of the X-ray tube, causing permanent damage to the X-ray tube. Do
not use the X-ray unit in environments where chlorine gases are generated. Take special care when handling samples
such as vinyl chloride materials which may generate chlorine gases.
2. Lead is used in the covers of machines equipped with an X-ray unit.
Although lead is sealed within the covers so that the lead portions cannot be directly touched, use caution since lead is
known as heavy metal having harmful effects.
3. A safety key is provided for machines equipped with an X-ray unit.
The safety key must be managed by the supervisor of the machine.