YAMAHA errer code-a.pdf - 第20页

Ea - 20 ERROR MESSAGES LIST Ea Ea01019 Ea01020 Ea01021 Ea01022 Ea01023 Ea01024 Ea01025 Ea01026 Ea01027 Ea01028 Ea01029 Ea01030 Ea01031 Ea01032 OPTION ERROR This option is not implemented in this software. This func- tion…

Ea -19

ERROR MESSAGES LIST

Ea00911

Ea00920

Ea00921

Ea00922

Ea00925

Ea00926

Ea00950

Ea00951

Ea00952

Ea00953

Ea00954

Ea00955

Ea00956

ILLEGAL TRAY DATA DURING RUNNING-2

Meaning: Illegal data during running.

Recovering: Pls. RESET RUNNING.

COMP.GLOBAL TO TEXT had been completed.

To use EXPERT SETUP, start EXPERT SETUP right now.

SET FROM/TO DATABASE has been completed.

SET TO STATIC_COMPONENT___ has been completed.

Please use this command in Component Info.

Please read the help message carefully before execut-

ing this command.Ready to execute database matching?

Press the [SPACE] key to execute, or any other key to

abort.

CO-PLANARITY CHECK ERROR

Head down position sensor error. Please check the me-

chanical position of Co-Planarity sensor and sensor

sensivity.

CO-PLANARITY CHECK ERROR

Horizontal scanning safety check sensor of Co-Planarity

checked danger. Bad position of Co-Planarity sensor, or

picking error is too big. his component. Or size of com-

ponent is no good. Please check these items.

CO-PLANARITY CHECK ERROR

Error of position of Co-Planarity Check sensor. Please

check the mechanical position of Co-Planarity Check

sensor.

CO-PLANARITY CHECK ERROR

This component is out of regulation. of Co-Planarity Check

sensor. Only "QFP","SOP"is suitable. Or 20.5mm square

is minimum size and 45mm square is maximum size for

Co-Planarity check.

CO-PLANARITY CHECK ERROR

Picking position is bad for Co-Planarity Check. Picking

error is too large for Co-Planarity. Please check the pick-

ing position.

CO-PLANARITY CHECK ERROR

Co-linearity check found the lead out of tolerance.

CO-PLANARITY CHECK ERROR

Vacuum check error.

(meaning)A problem occurred with tray changer control during op-

eration.

(cause)Because the operation is complex, the system has lost track

of where the component is.

(remedy)Reset the system.

(Meaning)This message appears when the [COMP. GROVAL TO

TEXT] command had been completed using YVOS2 with option

EXPERT SW.

(Cause)[COMP. GROVAL TO TEXT] command had been com-

pleted.(Remedy)To execute expert SW, click the icon of expert SW,

or just press [enter] key for another operation.

(Meaning)Succeeded in [SET FROM DATABASE] or reserse set

into the database.

(Cause)[SET FROM DATABASE] or reserse set into the database

had been done.

(Remedy)Press [Enter].

(Meaning)The component data had been registered into the

STATIC_COMPONENT.

(Cause)The command to register the data into STATIC COMPO-

NENT had been executed.

(Remedy)Press [Enter].

(Meaning)A command only for component information is used for

another data.

(Cause)The MAIN WINDOW is not component info.

(Remedy)Press[F3] to change window into component info.

(Meaning)This is the warning message before executing database-

matching.

(Cause)DATABASE MATCHING had been commanded.

(Remedy)Press [SPACE] to execute or other key to cancel.

(meaning)A lead which is not securely attached has been detected,

but the sensor which causes the head to descend has not reacted.

(cause)The sensor has malfunctioned, or there is a problem with

the position coordinates of thedevice which detects leads which

are not securely attached.

(remedy) Trace the position coordinates using the machine data

editing function, and check the operation of the sensor.

(meaning)When an attempt was made to detect loose leads, the

safety check sensor on the device which detects leads which are

not securely attached alerted the user of danger.

(cause)The sensor may have reacted to the sensor which prevents

contact between the nozzles and components and the loose lead

detection (co-planarity) unit.

(remedy)Check the relative heights of the units, and if the sensor

needs to be adjusted, adjust it. Otherwise, if the pickup tolerance

for the components is excessive, adjust the pickup position.

(meaning)There is a problem with the position data for the loose

lead detection (co-planarity) unit.

(cause)The data has not been adjusted properly.

(remedy)Re-adjust the data.

(meaning)An attempt was made to detect loose leads on a compo-

nent which is not within the specifications of the loose lead detec-

tion (co-planarity) unit.

(cause)Detection of loose leads is specified in the data for compo-

nents whose specifications do not allow this type of detection.

(remedy)If there is an error in the component size or other data,

change the input value. Otherwise do not specify that the loose

lead detection (co-planarity) function be used.

(meaning)Because the pickup tolerance is excessive, the loose lead

detection (co-planarity) unit cannot be used.

(cause)The pickup tolerance is excessive.

(remedy)Raise the level of the pickup precision, or stabilize the

pickup conditions.

(meaning)A lead has been detected which is not within the range

set for results of loose lead detection (co-planarity).

(cause)The lead on the component is not securely attached.

(remedy)Do not use that component, or, if the value set for loose

lead detection (co-planarity) is too strict, change it to a more le-

nient setting.

(meaning)During detection of loose leads, the pickup sensor which

checks for the presence of components detects that there are no

more components.

(cause) The component may have fallen off during lead detection,

or the pickup and mounting level has not been set properly.

(remedy)Check to see if the component is still on the nozzle, and

check the setting of the pickup and mounting level.

Ea00957

Ea00958

Ea00959

Ea00970

Ea00999

Ea01000

Ea01001

Ea01002

Ea01003

Ea01004

Ea01010

Ea01018

CO-PLANARITY CHECK ERROR

CO-PLANARITY CHECK ERRORdition Error.

Please once reset and run. Co-Planarity Check sensor

and board Condition Error. Please once reset and run.

In case machine does not recover by this way, please

check the indicator of Lase Lead Locator board. If it is

flashing in red, once power off and power on again.

CO-PLANARITY CHECK ERROR

Co-Planarity Check sensor cannot get good result. Please

check the mechanical position. of Co-Planarity Check

sensor.

CO-PLANARITY CHECK ERROR

Co-Planarity Check sensor data error.", "SOP". In case

for using Co-Planarity Check these conditions are need,

1. Vision type is suitable only "QFP","SOP".

2. There is option of Co-Planarity.

3. Component size is within reguration.

PCB FILE READ ERROR

The amount of data exceeds the limit, 2560p(points).

The counting of each lines are as follows.

Mount Data'(1p),

Block Repeat'(2p),

Fiducial Inf'(3p),

PreDispense'(1p),

DotDispense'(1p).

Reduce the number of data.

RETRY active.

PCB name : [CUK93001]

CAUTION: PCB data is new or changed and requires a

backup.

Insert a backup DISKETTE in the FLOPPY DRIVE, se-

lect "START MAINTENANCE" and press the [ENTER]

key, or.. Press the [ESC] key to skip the backup.

PCB name : [CUK93001]

Writing backup data now.

Please wait a moment....

PCB name : [CUK93001]

FLOPPY DISK DRIVE is not ready.

Data cannot be backed up.

PCB name : [CUK93001]

DISK is not prepared for VIOS.

Data cannot be backed up.

PCB name : [CUK93001]

Cannot execute data backup. The reason is as follows.

■ Floppy disk is full.

■ Floppy disk has bad sector.

PCB name : [CUK93001]

Now reading data.

Please wait a moment....

/0000/1000/E

OPTION ERROR

This option is not implemented in this software. This func-

tion is available only in the surface-mounter.

(meaning)Communication with the loose lead detection (co-planar-

ity) unit is not

(cause)There is a problem with the communications cable connect-

ing the loose lead detection (co-planarity) unit, or the unit itself is

defective

(remedy)Contact the manufacturer.

(meaning)An error occurred in detecting loose leads (checking co-

planarity).

(cause)The component lead does not pass through the area it must

be in in order for loose leads tobe detected.

(remedy)Re-adjust the height data and the X and Y position data

for the loose lead detection (co-planarity) unit, which are found

among the component thickness or the mechanical coordinates.

(meaning)The conditions necessary for executing loose lead de-

tection (co-planarity) have not been met.

(cause)The data has not been specified correctly.

(remedy)Check to see whether the recognition type is set to QFP or

SOP, and that the loose lead detection (co-planarity) unit has been

installed. If the above conditions cannot be met do not use the loose

lead detection (co-planarity) unit.

(meaning) File being read exceeds specified file length.

(cause) Using CAD conversion or other means, data was created

which exceeds specified file length.

(remedy) Delete data which exceeds file length.

(meaning)This is not an error message.

(cause)None

(remedy)None

(meaning)This is a warning that PCB data exists which has been

edited, but the revised version has not been backed up.

(cause)There is PCB data for which changes have been entered,

but the revised data has not been backed up.

(remedy)Insert the PCB data disk in the floppy disk drive and press

the Enter key. To proceed without backing up the data, simply press

the ESC key.

(meaning)This message indicates that data is being backed up. It

is not an error message.

(cause)None

(remedy)Wait until the process has been completed.

(meaning)An attempt was made to back up data, but no floppy disk

which can read the data has been inserted in the drive.

(cause)The backup process was started without inserting the floppy

disk.

(remedy)Insert the floppy disk and then press the Enter key once

more. If no floppy disk is available, press the ESC key.

(meaning)An attempt was made to back up data, but the floppy disk

has not yet been made the PCB data disk.

(cause)A floppy disk is being used for which the PCB data disk

creation command has not been used to make it a PCB data disk.

(remedy)Use a floppy disk which has been made into the PCB data

disk using the PCB data disk creation command. To cancel the

backup process, press the ESC key.

(meaning)An error occurred when backing up data.

(cause)The floppy disk is full; there is a faulty sector on the disk; or

the floppy disk was ejected before the backup process was com-

pleted.

(remedy)Insert a different PCB data disk and execute the command

again.

(meaning)An attempt was made to use optional equipment which

has not been installed, or an option is being used which can be

used only with the mounter itself.

(cause)Same as above.

(remedy)None

Ea -20

ERROR MESSAGES LIST

Ea01019

Ea01020

Ea01021

Ea01022

Ea01023

Ea01024

Ea01025

Ea01026

Ea01027

Ea01028

Ea01029

Ea01030

Ea01031

Ea01032

OPTION ERROR

This option is not implemented in this software. This func-

tion is not available.

COMMAND ERROR

You cannot select this item, because the PROTECT LI-

CENSE is not given.

RUNNING PCB NOT SELECTED

Because "PRODUCTION PCB" had not indicated in the

<<RUNNING>> mode, you cannot select this mode at

this moment.

OPTION ERROR

This option is not implemented in this software. This func-

tion is for an other type of machine.

WARNING: NOT ENOUGH HDD SPACE

Free space on Hard Disk is less than 10MB. To avoid the

possibility that you cannot save new data anymore and

that data might get lost, it is best to create, now, new

space on the hard disk. Copy unused PCB data to floppy,

and delete from the hard disk.

ERROR:NOT A MOUNT DATA.

This function is available only if OBJECT is MOUNT.

Please select MOUNT in [A1 MAIN WINDOW] at first.

HardWare-key is not ready.

Put HardWare-key to the printer port, and boot again.

You can't add any more PCB data.

Copy PCB data to floppy disk, and reduce the number of

PCB data in HDD.

Only the machine data of the surface mounter and the

dispenser can be edited in this mode.

This machine is not UFOS type.

Copy into the data area for UFOS machine to convert.

On PC,

UFOS(FD)<->VIOS CONVERT

VIOS->PRINT FORMAT(PRT\)

is not able for a data on floppy. Copy into the data area

for UFOS machine in PC.

Not enough memory to execute.

The data [STATIC_COMPONENTS] is component data

common for all PCB DATA in a machine.

Only COMPONENT INFORMATION is available for the

data [STATIC_COMPONENTS].

(meaning)An attempt was made to use optional equipment which

has not been installed, or an option is being used which can be

used only with the mounter itself.

(cause)Same as above.

(remedy)None

(meaning)An item has been selected which cannot be used be-

cause the protective license has not been input.

(cause)The protective license has not been input.

(remedy)Input the protective license and run the process again.

(meaning)The selected command cannot be executed because the

PCB to be produced in the automatic operation mode has not been

decided.

(cause)The PCB to be produced in the automatic operation mode

has not been decided.

(remedy)Specify the PCB to be produced in the automatic opera-

tion mode and then execute the command again.

(meaning)An attempt was made to use optional equipment designed

for a different model.

(cause)Same as above.

(remedy)None

(meaning)This alerts the user to danger arising from the remaining

capacity of the hard disk dropping to less than 10 megabytes.

(cause)There is too much data.

(remedy)Back up any unnecessary PCB data and delete it from

the hard disk.

(meaning)A function which can only be used with the placing infor-

mation has been selected although the placing information is not

shown on the editing screen.

(cause)The placing information is not shown on the editing screen.

(remedy)Change the editing screen to show the placing informa-

tion.

(meaning) The hard keys provided by the manufacturer have not

been connected to the personal computer for which the offline soft-

ware is designed.

(cause)The computer does not have the proper hard keys, or the

hard keys have not been correctly installed in the printer terminal.

(remedy)Install the hard keys correctly in the printer terminal.

(meaning)No more PCB data can be registered.

(cause)There is not enough space left on the hard disk, or the num-

ber of PCB data registered exceeds the allowable limit.

(remedy)Back up any unnecessary PCB data and delete it from

the hard disk.

(meaning)Only the machine data of the surface mounter and the

dispenser can be edited.

(cause)Same as above.

(remedy)None

(meaning)An attempt was made to carry out UFOS/ VIOS conver-

sion on a VIOS machine.

(cause)Same as above.

(remedy)Switch the screen to a registered UFOS machine and use

that screen for the UFOS/VIOS conversion.

(meaning)With the YVOS, floppy disks cannot be used to generate

data for UFOS/VIOS data conversion and VIOS printing data con-

version.

(cause)The data to be converted is contained on a floppy disk and

not on the hard disk.

(remedy)Copy the data to be converted from the floppy disk to the

hard disk and then run the conversion function again.

(meaning)Not enough memory can be assured to run the program.

(cause)There is a problem with the board or another element.

(remedy)Check to see how often the problem occurs, and contact

the manufacturer.

(meaning)The data called STATIC-COMPONENTS is called fixed

component information and is component information which is com-

mon to all PCBs. This data is used with components which are not

removed when setups are changed on the feeder plate or tray

changer. This is not an error message.

(cause)None

(remedy)None

(meaning) STATIC-COMPONENTS is fixed component data and

cannot be edited apart from component information.

(cause)None

(remedy)None

Ea01033

Ea01034

Ea01035

Ea01037

Ea01040

Ea01041

Ea01045

/BASE `

Ea01045

/APL=4

Ea01046

Ea01200

Ea01202

Ea01203

Ea01204

COMMAND ERROR

This command is not (yet) available.

Please wait a moment

while changing modes...

MOVING AREA OVER

The target position is outside the moving area.

Axes X1

Are you sure?

[ESC] : No

Others: Yes

It isn't able to display templet on this window.

You can display templet on mark-information window.

It's not reserved extent of copy or delete.

YVOS2 stops copying or deleting.

<<Daily Examination>> <<Check>> <<Predicted Error>>

>NOZZLE TIP Break, Solder Pick-up, Recognition

Spring func . Pick-up, Comp. damage

>LEAF SPRING Spring func. Placement, Nozzle

change

>NOZZLE HOLDER Spring func. Pick-up, Comp. dam

age

>LASER WINDOW Cleaning Recognition

>CAMERA LENS Cleaning Recognition

>FEEDER Shutter Feeding, Pick-up

>FEEDER PLATE Cleaning Placement, Pick-up

Please refer to the manuals in detail.

<<Daily Examination for Dispenser>>

<<Item>>:<<Check point>>:<<Problems to be pre-

vented>>

<Nozzle hole>:

Stuffed with glue :Unstable dot

Shortage of cleaning :Unstable dot

Old or quality changed :Unstable dot

Please refer to chap. 4 of [User's Manual] in detail.

YEAR 2000 DETECTED

Thank you to use our surface mounter and dispenser.

At the 1st power on after 1 Jan 2000, please set the date

value again.

To correct the date value again, the command 4/2/D4 is

also available.

Failed to create VIOS PCB file. This can be cause by the

following:

■ Total number of PCB data exceeds 127

■ PCB name already exists.

■ Not enough space to create PCB on Hard Disk.

Failed to copy VIOS PCB file.

Failed to remove VIOS PCB file.

WARNING:VIOS FLOPPY IN THE DRIVE IS NOT FAM-

ILY

The floppy in the drive seems to be VIOS type.

The floppy in the drive has unknown machine data.

The floppy in the drive is not made by this machine.

Press [ENTER]key to select machine and open floppy

drive, or any other key to abort.

(meaning)The specified command cannot be used.

(cause)An attempt was made to use a command which cannot be

used.

(remedy)None

(meaning)The mode is being switched. This is not an error mes-

sage.

(cause)None

(remedy)Wait until the process has been completed.

(meaning)The target positions of the displayed axes are outside

the moving area.

(cause)Same as above.

(remedy)Modify target positions.

(meaning)Confirmation of user operation.

(cause)None

(remedy)None

(meaning)Cannot display templet.

(cause)This window is not mark-information.

(remedy)Move to mark-information window.

(meaning)YVOS stops copying or deleting.

(cause)It's not reserved extent.

(remedy)After reserving extent, copy or del.

(Meaning)This message is to show daily required maintenance items

just after power up of the machine.

(Cause)Starting up of the machine.

(Remedy)Read message and press [Enter].

Or press [Enter] during the starting up to skip this message.

(Meaning)This message is to show daily required maintenance items

just after power up of the machine.

(Cause)Starting up of the machine.

(Remedy)Read message and press [Enter].

Or press [Enter] during the starting up to skip this message.

(Meaning)Reporting the date and time data should be done again,

and requiring to set correct data.

(Cause)Starting up of the machine just after year 2000 comes.

(Remedy)ÅzSet date and time.

(meaning)An error occurred in registering VIOS PCB data.

(cause)An attempt was made to create data which exceeds the

maximum limit of 127 PCBs; an attempt was made to register new

data under an already existing PCB name; there is not enough space

left on the hard disk; or there is not enough space left on the floppy

disk.

(remedy)If the maximum limit of 127 PCBs has been exceeded,

copy some of the data to a floppy disk and then delete it from the

hard disk. If you are trying to create new data under an already

existing PCB name, register the data again under a different name.

(meaning)An error occurred when copying a VIOS PCB file.

(cause)There is not enough space on the destination disk; the num-

ber of data registered on the destination disk has already reached

127; or there is a problem with the disk containing the original data.

(remedy)Reduce the amount of data registered on the destination

disk, and check the original disk and the data for problems.

(meaning) An error occurred when deleting a PCB file.

(cause) There is a problem with the drive or the disk.

(remedy) Cancel the write protect function on the floppy disk.

(meaning) An attempt was made to use floppy disk created using a

machine not registered in YVOS2.

(cause) An attempt was made to use YVOS2 to process floppy disk

from machine which has not been registered.

(remedy) Create PCB data disk in PCB data management mode, and

change attributes of that floppy disk to those of machine registered in

YVOS2. Or, press [ENTER] key and forcibly select target machine.

Ea -21

ERROR MESSAGES LIST

Ea01205

Ea01206

Ea01207

Ea01208

Ea01209

Ea01210

Ea01211

Ea01212

WARNING:UFOS FLOPPY IN THE DRIVE IS NOT FAM-

ILY

The floppy in the drive seems to be UFOS type. The floppy

in the drive has unknown machine data. The floppy in

the drive is not a one made by this machine.

ERROR: This command is available during vios-mode.

Illegal machine selection:

Undefined machine can not be selected in VIOS mode.

A machine not UFOS can not be selected in UFOS mode.

Ready to remake SYSTEM DATA BACKUP DISK.

Please insert

SYSTEM DATA BACKUP DISK for MOUNTER

and hit [ENTER].

Ready to remake SYSTEM DATA BACKUP DISK.

Please insert

SYSTEM DATA BACKUP DISK for YVOS

and hit [ENTER].

Failed to complete to update SYSTEM DATA BACKUP

DISK.

You can not switch machine. The machine is decided by

PCB data disk in the floppy drive. To switch machine,

take out the PCB data disk from the floppy drive and se-

lect

[ A1 SEARCH DRIVE ] first.

ASCII DATA Pick Up error.

ERROR CODE1 : 2

Detail :1:Comp.Info.

2:Mark Info.

3:PCB Info.

0:Others. Refer to ERROR CODE2.

ERROR CODE2 : 5

Detail : 0:LocalBadMrk Info.

1:Pre Disp. Info.

2:Dot Disp. Info.

5:Local Fidu.Info.

6:Mount Info.

7:PCB Origin

8:Blk Repeat Info.

9:PCB Size

10:PCB Fiducial

11:BLOCK Fiducial

12:PCB Badmark

13:BLOCK Badmark

ASCII->VIOS Conversion error.

ERROR CODE1 : 3

Detail : 1:Comp.Info.

2:Mark Info.

3:PCB Info.

0:Others. Refer to ERROR CODE2.

ERROR CODE2 : 10

Detail : 0:LocalBadMrk Info.

1:Pre Disp. Info.

2:Dot Disp. Info.

5:Local Fidu.Info.

6:Mount Info.

7:PCB Origin

8:Blk Repeat Info.

9:PCB Size

10:PCB Fiducial

11:BLOCK Fiducial

12:PCB Badmark

13:BLOCK Badmark

(meaning) A UFOS floppy which has not been registered on the

YVOS2 has been detected in the floppy disk drive.

(cause)Same as above.

(remedy)In the PCB data control mode, shift to the UFOS data

directory and then create the PCB data disk.

(meaning)A command which can only be used in the VIOS mode

was used in the UFOS mode.

(cause)The screen does not match the operation.

(remedy) Eject the floppy disk from the drive and select the VIOS

mode. Then execute the command in the VIOS mode.

(meaning)The wrong machine number was selected

(cause) An attempt was made to select a VIOS machine in the

UFOS mode, or an attempt was made to use a machine which has

not been registered as a VIOS or UFOS machine.

(remedy) When selecting a UFOS machine, first eject the floppy

disk from the drive and shift to the UFOS mode. Then select the

machine.

(meaning)This notifies the user to insert the data disk contained on

the installation disk in the disk drive in order to back up system

data.

(cause) None

(remedy) Insert the specified floppy disk in the disk drive.

(meaning)System data could not be backed up.

(cause)There may be a problem with the disk.

(remedy)Contact the manufacturer for instructions.

(meaning)It cannot switch machine.

(cause)The machine decided by PCB disk in the floppy drive.

(remedy)Take out the PCB data disk from the floppy drive and se-

lect [ A1 SEARCH DRIVE ] first.

(meaning)It cannot find out the convert lines.

(cause)There is nothing inside the CAD data that inputed string of

search item.

(remedy)Look "Serch" over again.

(meaning)It cannot convert the data from CAD to VIOS.

(cause)There is no character inside the CAD data.

(remedy)Look "Data get" over again.

Ea01221

Ea01222

Ea01223

Ea01230

Ea01231

Ea01232

Ea01233

Ea01234

Ea01235

Ea01236

ASCII data analyzing error. The following error occurs.

1:Comp.Info.