YAMAHA errer code-a.pdf - 第9页

Ea - 9 ERROR MESSAGES LIST Ea Ea00246 Ea00247 Ea00248 Ea00249 Ea00250 Ea00251 Ea00260 Ea00261 Ea00262 Ea00270 Ea00271 Ea00272 Ea00273 PCB DA TA ERROR This component body size is too big.gh. So this compo- nent is cannot …

Ea -8

ERROR MESSAGES LIST

Ea00204

Ea00205

Ea00206

Ea00207

Ea00220

Ea00221

Ea00222

Ea00223

Ea00230

Ea00231

Ea00232

NOZZLE STATION ERROR

There is no nozzle present for next sequence. Please

check nozzle station data.

Head No. 2

Station No. 11

NOZZLE STATION ERROR

There is more than one nozzle for next sequence. Please

check sensors of the nozzle station and insert the appro-

priate nozzle(s).

Head No. 2

Station No. 11

DATA ERROR

The next mount sequence specifies that more than three

heads are used or the head number used is 3 or more.

Please check the mount data.

DATA ERROR

The next mount sequence specifies that more than three

heads are used or the head number used is 3 or more.

Please check the mount data.

BACKLIGHT POSITION ERROR

1. Ensure all nozzles not in use are in station.

2. Ensure the sensor knows nozzles are there.

3. Push EMG sw. and pull up no.2 head to up-end, push

down no.1 head to lower pos.

4. In case the step 1-3 had not solved problem, Please

move backlight to right position by CHANGE BACKLIGHT

command.

NOZZLE CHANGE ERROR

Now, head is picking the component. Head can't change

the nozzle.

OPERATION ERROR

1. Ensure all nozzles not in use are in station.

2. Ensure the sensor knows nozzles are there.

3. Push EMG sw. Check the safety of head, nozzles,

nozzle station.

4. In case the step 1-3 had not solved problem, Please

ensure safety by manual.

NOZZLE STATION CLAMPING ERROR

Unable to clamp nozzles in the nozzle station.

Correct the condition of the nozzle station.

4-Point Fiducial Data Error

Fiducial No.5

Setting of [Type] is not correct. Please set like this,

No. 5 --> [4Local-M]

No. 6 --> [4Local-S]

4-Point Fiducial Data Error

Fiducial No.5

Setting of [Mark] is not correct. Please set same number.

4-Point Fiducial Data Error

Fiducial No.5

Distance between point and another point is too short.

Please set this distance more than 5(mm). Please set

coordinates of 4-point again.

(meaning)The nozzle intended for use is not in the nozzle station.

(cause)The nozzle which is planned for use has not been specified

in the nozzle station information.

(remedy)Check the settings in the nozzle station information.

(meaning)The nozzle station contains more than one of the same

nozzle.

(cause)Two of the same nozzle have been specified in the nozzle

station information.

(remedy)Check the nozzle station information.

(meaning)A head number of 3 or higher has been specified in the

mounting data for a mounter which has only two heads.

(cause)A head number of 3 or more has been specified.

(remedy)Change the head number in the placing data to 1 or 2.

(meaning)Vision recognition is specified with head 2.

(cause)With this machine, vision recognition cannot be carried out

using head 2.

(remedy)Change the head number to 1, or change to laser recog-

nition.

(meaning)The backlighting illumination is dangerously positioned.

(cause)When an attempt was made to change nozzles, the nozzles

could not be changed because the position of the backlighting illu-

mination was dangerous.

(remedy)Check to see that all of the nozzles are in the nozzle sta-

tion, and that the sensor reacts to all of the nozzles in the nozzle

station. Next, press the Emergency Stop button and move head 2

to its upper end and head 1 below the backlighting illumination

Then use the backlighting illumination movement command to move

the backlighting illumination to the right.

(meaning)The nozzle cannot be replaced because a component

has been picked up.

(cause)Two causes are possible: the head vacuum is on, or the

head vacuum is on and a component has been detected by the

vacuum level sensor.

(remedy)Remove the component from the nozzle or turn off the

head vacuum.

Accident happened for YV-120 machine Nozzle changing is failed.

According to the message and recover this accident

(meaning)Although the upper plate of the nozzle station slides and

two sensor for both edge (only single side for YVL80) detect the

actual action of the plate, at least 1 sensor do not response to the

command to slide the plate.

(cause)qPlate is mechanically stuck. The position or the sensitivity

of the sensor is not adjusted.

(remedy)Repair the sliding plate, or adjust the sensor.

Please set fiducial data according to "Error Message".

Please set 4 point fiducial data like shown in "Error Message".

Ea00233

Ea00234

Ea00235

Ea00236

Ea00237

Ea00238

Ea00239

Ea00240

Ea00241

Ea00242

Ea00243

Ea00244

Ea00245

4-Point Fiducial Data Error

Fiducial No.5

In quadrilaterals which is composed of 4-point fiducial,

distance between one point and one side of quadrilater-

als is less than 5(mm). Please set coordinates of 4-point

again.

4-Point Fiducial Data Error

Fiducial No.5

In quadrilaterals which is composed of 4-point fiducial,

there is interior angle which is over 180 degree. sage.

Please set coordinates of 4-point again.

4-Point Fiducial Data Error

Fiducial No.5

It is impossible to use this fiducial number which is se-

lected in this Mount Data, because this data is [4Local-

S]. Please use [4Local-M] Fiducial number of 4-point fi-

ducial.

4-Point Fiducial Data Error

Fiducial No.4

It is impossible to use this fiducial data, because this data

is [Note]. Please change from [Note] to [Exec].

PCB DATA ERROR

Mount data No.4

Fiducial data No.6

It is impossible to use this fiducial data, because this data

is [Note]. Please change from [Note] to [Exec].

4-Point Fiducial Data Errorpe Error

Mount data No. 6

Fiducial data No. 2

Coordinate of mount point is out of range of 4-point-fidu-

cial. to use this function in Please don't use this 4-point

fiducial for this mount point.

Data Warning

The piece of block that you defined in PCB Information is

different from piece of local badmark.

In this case, machine cannot count Block Numbers in

Production History. If you want to count Block Numbers,

change number of block in PCB Information.

PCB DATA ERROR

No mark data available for the local fiducial. Or the mark

data is not for fiducial.

Mount Data 1

Mark Data 2

PCB DATA WARNING

Height of component is out of range for "Multi Cam".

Component Data 2

It may be impossible to recognize this component by us-

ing "Multi.Cam". It is necessary to check whether this

component is able to be recognized by using "Multi.Cam"

in [ADJUST ASSISTANT]. To continue "Data-Check",

press any key.

MARK DATA WARNING

Templet image can't be downloaded to the vision.

•Did you create templet image of target mark?

•Don't you make too many mark data in one PCB?

•Don't you want to use too many kind of mark?

PCB DATA ERROR

Effective data was not found. There is no data to execute.

Use 'PASS'.

PCB DATA ERROR

There is no mark pattern data. Some pattern matching

function is used for fiducial mark, but it has no pattern

matching data. This data was made by executing of [Ad-

just Assistant] in Mark Information.

PCB DATA ERROR

This component body height is too high. So this compo-

nent is cannot recognize by equipped camera.

Mount Data 10

Component Data 5

Please set 4 point fiducial data like shown in "Error Message".

Set same number of block in PCB Information as total local badmark

number.

(meaning)The mark data for the specified not an fiducial does not

exist.

(cause)No mark data exists.

(remedy)Create the mark data.

(meaning)It may be impossible to recognized this component by

using "Multi.Cam" because height of this component is out of range

for "Multi.Cam"

(remedy)Please check recognition of this component in [ADJUST

ASSISTANT].

(meaning) No effective data in the PCB data.

(remedy) Use "PASS".

(meaning) There is no data for pattern matching.

(remedy) Make data for pattern matching of fiducial mark in mark

information.

(meaning) This component is too high for its height.

(remedy) Check camera coordinate data.

Ea -9

ERROR MESSAGES LIST

Ea00246

Ea00247

Ea00248

Ea00249

Ea00250

Ea00251

Ea00260

Ea00261

Ea00262

Ea00270

Ea00271

Ea00272

Ea00273

PCB DATA ERROR

This component body size is too big.gh. So this compo-

nent is cannot recognize by equipped camera.

Mount Data 10

Component Data 5

PCB DATA ERROR

"Mount Action" reserved component number is "Fine

Type", but fine mode reserved head is "Impossible".

Mount data 10

Head number 5

Please reserve component number not "Fine Type", etc.

COMPONENT DATA ERROR

Feeder Type for this component was not defined. Specify

the feeder type data in Component Info.

Mount Data 12

Component Data 3

COMPONENT DATA ERROR

Feeder Position must be "Teaching" or "Relative" for stick

feeder component. Input Feeder Pos_X,Y:

In case "Teaching", from the datum of machine origin.

In case "Relative", from the datum of 8mm tape feeder

pickup position.

Component data 3

COMMUNICATION ERROR

Failure of communicating with LOADER. One of the fol-

lowing could cause this error:

q LOADER or UNROADER is turned off power.

w LOADER or UNROADER is in emergency stop.

e LOADER or UNROADER is in auto-running.

r LOADER or UNROADER has already received PCB

width data after power-on.

If you don't want to repeat communicating with LOADER

Please push [TAB] keys.

If you want to repeat communicating with LOADER Please

push other keys.

DUMP STATION DATA ERROR

The feeder number used for dump station is not defined.

It must not be 0. Please confirm it.

DUMP STATION DATA ERROR

The feeder number used for dump station is not suitable.

In case of SM112, if this number for A-table is defined

more than 101, then this error will happen. Please con-

firm it.

DUMP STATION DATA ERROR

The X,Y position of dump station is not suitable. All heads

must be reach on this position, but the current coordi-

nate is out of it. In case of SM112, dump station may be

set about from 16 to 40 feeder location number. Please

correct X,Y coordinate of dump station.

PCB DATA ERROR

There is no dispense head for dot dispensing. Check the

head type and nozzle type in 3-2-A1-[Head Offset].

Dot Dispense data 11

PCB DATA ERROR

Dot dispensing position is outside moving area.

Dot Dispense data 3

Axes X

Checking dot dispensing data. Please wait a moment.......

Dot Dispense data 4

Block number 3

PCB DATA ERROR

Local badmark position of dispense data is outside mov-

ing area.

Dispense data 4

Local Badmark data 3

Axes X

(meaning) This component is too big for its height.

(remedy) Check camera coordinate data.

(meaning) The head "FineMode" is "Impossible " cannot act by

"FineType".

(cause) Reserved head is FineMode Impossible, but reserved com-

ponent is "FineType".(remedy) Please do one of following ways.

• Change headnum Finemode Possible.

• Change component not Finetype.

• Change component data other type

• Change "FineMode" "Possible".

(meaning) Feeder Type was not defined yet.

(cause) It seems that component package parameter was changed

after feeder type was defined. So, feeder type was changed to "Not

Defined"

(remedy) Select right feeder type.

(meaning) Feeder position is set to "Automatic" but this is a stick

feeder component.

(cause) Stick feeder must set its feeder set position to "Teaching"

or "Relative".

(remedy) Set right setting for Feeder Position (Teaching or Rela-

tive). And input Feeder Pos_X,Y parameter.

In case "Teaching", input from the datum of machine origin

In case "Relative", input from the datum of 8mm tape feeder pick

up position

(meaning) Failure of communicating with LOADER.

(cause) Cause is shown in "Error Message".

(remedy)Please remove cause.

This message is not "Error Message".

(meaning)

(cause)None

(remedy)None

(meaning)Feeder number for dump station is 0.

(cause)Feeder number for dump station must be more than 1.

(remedy)Please set number again.

(meaning)Feeder number for dump station is 0.

(cause)There is no dump station on the table which feeder for a

component is attached.

(remedy)If no dump station, please abort to use. Please change

feeder location on same table to dump station. Please set more

than 1 in feeder number for dump station.

(meaning)Feeder number for dump station is 0.

(cause)Because all heads must be reached on this coordinate, but

current pos. is out of it.

(remedy)Please change the position of dump station, and change

the coordinate again.

(meaning)Illegal dispense head was defined in dot dispense data.

(cause)The head does not exist, or the head number is not dis-

pense head.

(remedy)Please input right head number.

(meaning)X,Y position of Dot Dispense data is out of moving area.

(cause)The position is out of software limit.

(remedy)Please set right X, Y position or set right head number.

(meaning)Data check about dot dispensing data is being now car-

ried on.

(cause)This is not error message.

(remedy)Please wait until data check finish.

(meaning)Local badmark position defined in Dot dispense data is

out of moving Area.

(cause)Local badmark position is out of software limit.

(remedy)Please input right local badmark position.

Ea00274

Ea00275

Ea00276

Ea00277

Ea00278

Ea00279

Ea00280

Ea00281

Ea00282

Ea00283

Ea00284

Ea00285

Ea00286

Ea00287

PCB DATA ERROR

There is no local badmark data for the dot dispense.

Dispense Data 4

Local Badmark Data 3

PCB DATA ERROR

There is no mark data of local badmark available for the

dot dispense data.

Dot Dispense Data 4

Local Badmark data 3

Mark data 5

PCB DATA ERROR

No local badmark data is set to "Note" for executable dot

dispense data. During production, "Note" data is ignored.

So if you want to use local badmark function, set this "

Exec". If not, set "0" for BadMk in dot dispensing data.

Dot Dispense Data 4

Local Badmark Data 3

4-Point Fiducial Data Error

Dot Dispense Data No 4

Fiducial Data No. 3

It is impossible to use this Fiducial number which is se-

lected in this Dot Dispense Data, because this data is

[4Local-S]. Please use [4Local-M] Fiducial number of 4-

point fiducial.

PCB DATA ERROR

Dot Dispense Data No. 4

Fiducial data No. 3

It is impossible to use this fiducial data, because this data

is [Note]. Please change from [Note] to [Exec].

PCB DATA ERROR

No fiducial data available for the dot dispense local fidu-

cial.

Dot Dispense data 4

Fiducial data 3

PCB DATA ERROR

No mark data available for the dot dispense local fidu-

cial.

Dot Dispense data 10

Fiducial data 5

Mark data 2

Checking pre dispensing data.

Please wait a moment.......

Pre Dispense data 4

Block number 3

PCB DATA ERROR

Pre dispensing position is outside moving area.

Pre Dispense data 3

Axes X

PCB DATA ERROR

There is no dispense head for pre dispensing.

Pre Dispense data 11

Head number 4

PCB DATA ERR

It is impossible to use "Point Fiducial" for Dispense. Please

check the mount data or fiducial data.

Dot Dispense data 5

Fiducial data 3

PCB DATA ERR

Illegal unit for pre dispensing. Defined unit for that head

is out of range for adequate unit.

Pre Dispense data 5

Head number 3

Unit 30

PCB DATA ERR

Illegal unit for dot dispensing. Defined unit for that head

is out of range for adequate unit.

Dot Dispense data 4

Head number 2

Unit 70

DOT STATION PITCH ERR

Dot station pitch either X direction or Y direction must be

set "0". Please check the dot station pitch X,Y.

(meaning)Local badmark data for dot dispense data does not ex-

ist.

(cause)Local badmark data have not defined in local badmark in-

formation yet.

(remedy)Please define local badmark data, if you use this function.

(meaning)There is not mark data for local badmark.

(cause)The mark data of Local badmark data for dot dispense have

not defined.

(remedy)Please define mark data in mark information for local

badmark of dot dispense data.

(meaning)The local badmark data of the dot dispense data is "Note"

data.

(cause)Local badmark that is "Note" is ignored during in running

condition.

(remedy)Please input "Exec" data of local badmark for dot dispense

data.

(meaning)The fiducial number of dot dispense data is "4Local-S"

data.

(cause)"4Local-S" data is not for setted in fiducial number of dot

dispense data.

(remedy)Please set "4Local-M" number.

(meaning)The fiducial number of dot dispense

(cause)"Note" data is ignored in running.

(remedy)Set "Exec" from "Note".

(meaning)There is no fiducial data for dot dispense data.

(cause)The fiducial number of dot dispense has not defined yet.

(remedy)Please make fiducial data

(meaning)There is no mark data for fiducial data of dot dispense

data.

(cause)The mark data was not made yet.

(remedy)Please make mark data of fiducial of dot dispense, or if

you have already prepared mark data, set that mark number.

(meaning)Data check about pre dispensing data is being now

carryed on.

(cause)This is not error message.

(remedy)Please wait until data check finish.

(meaning)X,Y position of Pre Dispense data is out of moving area.

(cause)The position is out of software limit.

(remedy)Please set right X, Y position or set right head number.

(meaning)Illegal dispense head was defined in pre dispense data.

(cause)The head does not exist, or the head number is not dis-

pense head.

(remedy)Please input right head number.

Please don't use "Point Fiducial" for Dispense.

Non adequate dispensing unit was defined. Please set head num-

ber "0", to select head automatically, or input adequate value for

dispensing unit that is defined in NOZZLE-SPEC Information.

Non adequate dispensing unit was defined. Please set head num-

ber "0", to select head automatically, or input adequate value for

dispensing unit that is defined in NOZZLE-SPEC Information.

(meaning)DOT STATION PITCH ERR

(cause)Dot station pitch either X direction or Y direction must be

set "0".

(remedy)Please check the dot station pitch X,Y.

Ea -10

ERROR MESSAGES LIST

Ea00288

Ea00289

Ea00290

Ea00300

Ea00301

Ea00302

Ea00303

Ea00304

Ea00305

Ea00306

DOT STATION MAX MATRIX NUMBER ERR

Please set max matrix number to more than 1. Please

check the max matrix number.

DOT STATION DATA ERR

All heads can not be able to reach to dot station. Please

check the dot station position X,Y.

Head number X

Axis X

NOZZLE SPEC DATA ERROR

Failed to read the nozzle spec information. Please pre-

pare correct nozzle spec information. Select this com-

mand by

YVOS2....3-3-[A4 NOZZLE SPEC.INF]-[SM86D Type]

MACHINE.3-1-[A4 NOZZLE SPEC.INF]-[Shift]+[Enter]

Machine SM86D

file NO?\NZL_TIM.STS

Tray unit error : The component is not placed correctly on

the traverser station. If the component is on the station,

please remove it.

Mount data 765

Component data 153

Station 2

Next tray position is for the next pick sequence.

(X= 6 , Y= 3)

Tray unit error : Returned component is not placed cor-

rectly on the traverser station. If the component is on the

station, please remove it.

Mount data 765

Component data 153

Station 2

Tray unit error : Returned component is not placed cor-

rectly on the traverser station. If the component is on the

station, please remove it.

Mount data 765

Component data 153

Pallet 9

Next tray position is for the next pick sequence.

(X= 6 , Y= 3)

Tray unit error : Returned component is not placed cor-

rectly on the traverser station. If the component is on the

station, please remove it.

Mount data 765

Component data 153

Station 2

Next tray position is for the next pick sequence.

(X= 6 , Y= 3)

Tray unit error : Returned component is not placed cor-

rectly on the traverser station. If the component is on the

station, please remove it.

Mount data 765

Component data 153

Station 2

Tray unit error : Returned component is not placed cor-

rectly on the traverser station. If the component is on the

station, please remove it.

Mount data 765

Component data 153

Station 2

Tray unit error : Failed to store the pallet. To start produc-

tion again, please return the pallet to its assigned maga-

zine.

Mount data 765

Component data 153

Pallet 9

(meaning)DOT STATION MAX MATRIX NUMBER ERR

(cause)Please set max matrix number to more than 1.

(remedy)Please check the max matrix number.

(meaning)DOT STATION DATA ERR

(cause)All heads can not be able to reach to dot station.

(remedy)Please check the dot station position X,Y.

(meaning)NOZZLE SPEC DATA ERROR

(cause)Failed to read the nozzle spec information.

(remedy)Please prepare correct nozzle spec information.

(meaning) The tray changer was not able to place the supply com-

ponents on the traverser. If extra parts have been placed on the

specified traverser, remove them.

(cause)The pickup sensor on the station was not able to decide

correctly whether or not there was a component on the traverser.

(remedy) If there are extra components on the traverser, remove

them. If there is no problem with the components, and the sensor

has malfunctioned, re-adjust the sensor.

(meaning)Components which were returned from the main unit

could not be placed correctly on the traverser.

(cause)Components from the main unit were not placed correctly

on the traverser or fell off during transport.

(remedy)If components have fallen off, remove those components.

If the sensor judges that there are components on the traverser

when in actuality there are none, re-adjust the sensor.

(meaning)Components could not be picked up from the tray.

(cause)There were no components on the tray when the attempt

was made to pick them up, or components fell off when being moved

from the tray to the traverser.

(remedy)If components have fallen off, remove those components.

If components have run out, supply more.

(meaning)The external tray changer was not able to place compo-

nents properly on the traverser.

(cause)Components fell off of the external tray changer when be-

ing transported, or the sensor on the traverser judged that there

were no components on the traverser, even though there were.

(remedy)If components have fallen off, remove those components.

Adjust the pickup sensor for the traverser so that it judges correctly

whether or not there are components on the traverser.

(meaning)An error occurred when picking up components from the

traverser.

(cause)Components which should have been on the traverser were

not there, or an attempt was made to pick up components from the

traverser but the pickup head sensor or the traverser sensor was

not able to judge correctly whether there were components on the

traverser.

(remedy)Re-adjust the sensors, or, if there are components which

have fallen off, remove them.

(meaning)An error occurred when unknown component is on the

traverser station

(cause)Reset operation was done when some component is on

the traverser station Or traverser sensor was not able to judge the

existence of component.

(remedy)Please remove the component on the traverser station.

Or re-adjust the sensors of traverser.

(meaning)The pallet could not be housed in the magazine.

(cause)A mechanical problem occurred when the attempt was made

to house the pallet in the magazine.

(remedy)Press the Emergency Stop button and return the pallet to

the magazine manually.

Ea00307

Ea00308

Ea00310

Ea00311

Ea00312

Ea00313

Ea00314

Ea00315

Ea00316

Ea00317

Ea00320

Ea00330

Ea00350

Ea00351

Tray unit error : Failed to pull out the pallet. To start pro-

duction again, please return the pallet to its assigned

magazine.

Mount data 765

Component data 153

Pallet 9

Tray unit error : The hook action was performed incor-

rectly. Please check the following items:

1. Pallet (No. 9) access position.

2. The hook nail.

If the pallet is out of the magazine, then:

1. Make sure to push EMERGENCY STOP ON.

2. Remove the pallet from the stage section.

3. Return the pallet to its magazine.

Tray unit : The tray unit head or traverser station has a

component attached to its nozzle (pad). After removing

the component, please press any key.

Tray unit error : Abort the RESET process. If a pallet is

out of the magazine, please return it to its assigned maga-

zine.

Tray unit : Tray unit is working now! Please wait.....

Tray unit error : The pallet is out of the magazine. Return

the pallet to its assigned magazine.

Tray unit error : The door is open. Please close the door.

Tray unit error : Failed to store the pallet. To start produc-

tion again, please return the pallet to its assigned maga-

zine.

Tray unit error : Failed to pull out the pallet. To start pro-

duction again, please return the pallet to its assigned

magazine.

Tray unit error : The door is open. Please close the door.

Something wrong with door and check one.

Tray unit error : Unknown error

Now, head of machine or tray-changer is picking the com-

ponent. If "SET PALLET" will be executed, component

will drop from head. If you execute "SET PALLET", re-

move component from head and hit [Space] key. If you

cancel "SET PALLET", hit other key.

EMERGENCY STOP ON

The tray unit pallet is out of the magazine. When you push

[READY], make sure followings.

1. Can you keep on safety for another persons?

2. Have you kept on machine moving area?

3. Have you returned a pallet to magazine?

INTERLOCK ERROR

The tray unit pallet is out of the magazine. When you push

[READY], make sure followings.

1. Can you keep on safety for another persons?

2. Have you kept on machine moving area?

3. Have you returned a pallet to magazine?

(meaning)An error occurred when taking the pallet out of the maga-

zine.

(cause)For mechanical reasons, an error occurred when the pallet

was being taken out of the magazine.

(remedy)If the pallet has been ejected from the magazine too

abruptly, press the Emergency Stop button and return it to the maga-

zine manually.

(meaning)The hook did not respond correctly to an Open or Close

instruction.

(cause)The hook has not grasped the pallet at the correct position.

(remedy)Re-insert the hook at the correct position in the pallet, and

start the operation again from the beginning. If the pallet has been

ejected from the magazine too abruptly, however, press the Emer-

gency Stop button and return it to the magazine manually.

(meaning) Component exists in external tray changer which should

not be there.

(cause) Component pickup error by external tray traverser. Traverser

has skipped a component because of incorrect teaching of pickup

position or traverser position, or pickup error has been made by

main head traverser. Possibly, vacuum sensor of external tray

changer head or traverser station is incorrectly adjusted.

(remedy) Check component pickup position, traverser coordinates

on main unit side, and coordinates for traverser station on external

tray changer side. Adjust vacuum sensor of external tray changer

head and vacuum sensor of traverser station.

(meaning)This is a notification that the reset process has been in-

terrupted.

(cause)An interlock emergency stop instruction or similar instruc-

tion has been issued.

(remedy)If a pallet has been forcibly ejected return it to the maga-

zine.

(meaning)This is a notification that the tray changer is in operation.

(cause)None

(remedy)Please wait.

(meaning)The pallet has been forcibly ejected from the magazine.

(cause)Same as above.

(remedy)Return the pallet to the magazine.

(meaning)Operation cannot begin because the door of the external

tray changer is open.

(cause)The door of the external tray changer is open.

(remedy)Close the door which is open.

(meaning)An error has occurred in housing the pallet in the maga-

zine.

(cause)None

(remedy)Press the Emergency Stop button and return the pallet to

the magazine manually.

(meaning) An error occurred in taking the pallet out of the maga-

zine.

(cause)None

(remedy)Press the Emergency Stop button and return the pallet to

the magazine manually.

The door that normally closed is open. May be the door is broken.

(meaning)An internal problem has occurred in the tray changer.

(cause)The software version does not match.

(remedy)First, contact the manufacturer and then re-install the soft-

ware.

Remove the component from head of machine or Tray-Changer.

(meaning)The pallet has been forcibly ejected from the magazine.

(cause)None

(remedy)Press the Emergency Stop button, return the pallet to the

magazine, and press the Ready button.

(meaning)The pallet has been forcibly ejected from the magazine.

(cause)None

(remedy)Return the pallet correctly to the magazine and start the

operation again.