YAMAHA errer code-a.pdf - 第37页

Ea - 37 ERROR MESSAGES LIST Ea Ea07606 Ea07607 Ea07700 Ea07800 Ea07801 Ea07802 Ea07803 Ea07804 Ea07805 Ea07806 Ea07807 Ea07808 Ea07809 Ea07810 Ea0781 1 Ea07812 Ea07813 Ea07814 Ea07850 Ea07870 Ea07871 Ea07872 Ea07873 Ea07…

Ea -36

ERROR MESSAGES LIST

Ea06273

Ea07000

Ea07001

Ea07200

Ea07201

Ea07202

Ea07203

Ea07204

Ea07205

Ea07206

Ea07220

Ea07221

Ea07222

Ea07400

Ea07401

Ea07402

Ea07403

Ea07404

Ea07405

Ea07406

Ea07407

Ea07408

Ea07500

Ea07502

Ea07600

Ea07601

Ea07602

Ea07403

Ea07604

Ea07605

CANNOT EXECUTE IN SERVICE MODE

FILL UP CYLINDER

######### Now dispensing ##########

Head No.1

Please continue this command until dispense glue is is-

sued from nozzle of this head. After that, clean up the

dispense nozzle of that head.

And initialized total consumption of that head. To finish,

press any key.

DOT STATION

During pressing [Space] key, paper in "Dot Station" is

moved. To return to command menu, press [ESC] key.

CO-PLANARITY CHECK UNIT COMMUNICATION ER-

ROR

Please check the power supply to the unit and the con-

nection of the communication cable.

CO-PLANARITY CHECK UNIT PARAMETER ERROR

Failed to send the correct command to the Co-Planarity

check unit.

CO-PLANARITY CHECK UNIT TEMPERATURE ERROR

Temperature of co-planarity check unit is out of the stan-

dard (0Å`40 Celsius).

Please check whether the fun of the unit works or not.

CO-PLANARITY CHECK SENSOR HEAD ERROR

The cause may be the connection of the sensor head or

the sensor LD trouble.

CO-PLANARITY CHECK UNIT HARDWARE ERROR

There is trouble of memory access of co-planarity check

unit.

The cause may be the fully discharged battery.

CO-PLANARITY CHECK SENSOR HARDWARE ER-

ROR

The cause may be connection of the sensor and the unit

or power supply to the sensor controller.

CO-PLANARITY CHECK UNIT HARDWARE ERROR

Encoder pulse signal is not sent correctly to the co-pla-

narity check unit.

CO-PLANARITY CHECK SENSOR COORDINATE ER-

ROR

Coordinate of co-planarity check sensor position is not

proper.

Please check coordinate of the machine position of the

co-planarity check sensor. Axis

ALIGNMENT TYPE ERROR FOR CO-PLANARITY

CHECK

Alignment type of the component is not proper for co-

planarity check.

Component

Name

ALIGNMENT MODULE ERROR FOR CO-PLANARITY

CHECK

Alignment module of the component is not proper for co-

planarity check.

Component *** Name ***

Succeeded to write servo error information.

Canceled to write servo error information.

The reserved file already exists.

Overwrite?

[Enter] key : Execute to overwrite

Another key : Cancel

Failed to write servo error information.

CAUTION: Not exist the flash ROM, or cannot read the

information from the flash ROM. Please check the flash

ROM.

Failed to write servo error information. Not exist the disk,

or Reserved an illegal drive. Please check the drive. If

the disk isn’t inserted, please the write protected off and

insert.

Failed to write servo error information. Not exist the path.

Please check the path. Please make the directory in the

DISK_MAINTENANCE mode or reserve the other exist

path.

Failed to write servo error information. Cannot open the

file. Please check the disk is write protected on or off.

Failed to write servo error information. The cause is which

the following reason.

- The disk is write protected on.

- The disk is full.

- The disk or drive is destroyed.

Ready to start MOVING-AXIS.

Ensure that there are no obstructions to the head as-

sembly.

Push [Space] key to start.

Push any key to abort.

FATAL FAILURE VISION SYSTEM

Failure to communicate the hardware of Vision.

MACHINE DATA ERROR

Specification of camera number is incorrect. Please set

up parameters in [CameraCoordinate] again

Correct specification on SML80/SML88/SML88-2 is as

followings.

Camera1 : Moving Camera

Camera2 : Single Camera (1st)

Camera3 : Single Camera (2nd)

Camera4 : Single Camera (3rd)

MACHINE DATA ERROR

Specification of camera number is incorrect. Please set

up parameters in [CameraCoordinate] again

Correct specification on SM100/SM64/SM100-2 is as fol-

lowings.

Camera1 : Moving Camera

Camera2 : Single Camera

Camera3 : Multi Camera (2nd)

Camera4 : Multi Camera (1st)

MACHINE DATA ERROR

Specification of camera number is incorrect. Please set

up parameters in [CameraCoordinate] again

Correct specification on SM86D/SM100D/SM64D is as

followings.

Camera1 : Moving Camera

MACHINE DATA ERROR

Specification of camera number is incorrect. Please set

up parameters in [CameraCoordinate] again

Correct specification on SM112-3 is as followings.

Camera1A,Camera1B : Moving Camera

Camera4A,Camera4B : Multi Camera

MACHINE DATA ERROR

Specification of camera number is incorrect. Please set

up parameters in [CameraCoordinate] again

Correct specification on SML88-3 (tentative name) is as

followings.

MACHINE DATA ERROR

Specification of camera number is incorrect. Please set

up parameters in [CameraCoordinate] again

Correct specification on SM100-3 (tentative name) is as

followings.

(meaning) This message is explanation for [FULL UP CYLINDER].

(meaning)This massage is explanation for [DOT STATION].

(Meaning)No response from Co-planarity checking system.

(Cause)The power is not supplied to the system, or the communi-

cation cable is not connected, or the cable is damaged, or the power

switch of the system is off.

(Remedy)Confirm the cable connection and power on the system

again.

(Meaning)Problem had been detected in communication between

co-planarity checking system and the mounter.

(Cause)Extension communication card problem or cable problem..

(Remedy)Take off and put on the extension communication card,

and confirm the cable electrically, and power on again.

(Meaning)Co-planarity checking system detected temperature to

be out of the specifications.

(Cause)The air conditioner for the room is not working, or the fan

of the co-planarity control box is not working.

(Remedy)Confirm fan to be working, and turn on the air conditioner.

(Meaning)Problems had been detected on the communication be-

tween co-planarity sensor and the controlling box.

(Cause)Cable is not connected. Co-planarity sensor is out of con-

dition.

(Remedy)Confirm the condition of the cable and turn on the power

again.

(Meaning)The memory of the controlling box for co-planarity sen-

sor is destroyed.

(Cause)Battery down.

(Remedy)Exchange the battery if the power-up-again did not solve

the problem.

(Meaning)Problems had been detected on the communication be-

tween co-planarity sensor and the controlling box.

(Cause)Cable is not connected. Co-planarity sensor is out of con-

dition.

(Remedy)Confirm the condition of the cable and turn on the power

again.

(Meaning)The co-planarity checking control box could not read the

encoder signal of the mounter.

(Cause)The interface of the controlling box and the encoder of the

machine is not suitable. Shield of the encoder cable is not fine.

Electrical noise via the power line.

(Remedy)Confirm the power is not noisy, and confirm the cable

connection. Or if it is the initial trouble for the machine, confirm the

interface specification of the encoder signal.

(Meaning)The coordinate of Co-planarity in [position] page in

MCH_DATA is out of the area.

(Cause)Data is not adjusted.

(Remedy)Adjust data.

(Meaning)Although the co-planarity checking is for QFP/SOP and

others, and is not for the alignment type for this component.

(Cause)Component data has some contradiction.

(Remedy)Correct data.

(Meaning)This is warning message before to confirm the soft limit

value by actually traveling axis.

(Cause)

(Remedy)Confirm any obstacle is not in the area and press [SPACE].

Ea -37

ERROR MESSAGES LIST

Ea07606

Ea07607

Ea07700

Ea07800

Ea07801

Ea07802

Ea07803

Ea07804

Ea07805

Ea07806

Ea07807

Ea07808

Ea07809

Ea07810

Ea07811

Ea07812

Ea07813

Ea07814

Ea07850

Ea07870

Ea07871

Ea07872

Ea07873

Ea07874

Ea07875

Ea07876

Ea07877

Ea07900

Ea07901

MACHINE DATA ERROR

Specification of camera number is incorrect. Please set

up parameters in [CameraCoordinate] again

Correct specification on SML88Super (tentative name)

is as followings.

MACHINE DATA ERROR

Specification of camera number is incorrect. Please set

up parameters in [CameraCoordinate] again

Correct specification on SM100Twin (tentative name) is

as followings.

VICS HARDWARE ERROR

Please insert the vision board with following part num-

ber.KM5-M441H-020 (Bottom 3 numbers should be after

020.)

SOME COMPONENTS ARE NOT POSSIBLE TO PICK

The OPT-FLAG prevents the machine to pick up next

component.

Mount data ***

Component data *** Name ***

Head ***

SOME COMPONENTS ARE NOT POSSIBLE TO PICK

The head is already occupied by another component, and

the indicated picking action is not possible.

Mount data ***

Component data *** Name ***

Head ***

SOME COMPONENTS ARE NOT POSSIBLE TO PICK

A picking up group without rotation-action could not in-

clude a mounting data with some rotation.

Mount data ***

Component data *** Name ***

Head ***

SOME COMPONENT COULD NOT BE PICKED UP

By picking up this component, depending on the pick up

accuracy, the component could hit the component on

neighbor nozzle.

Mount data ***

Component data *** Name ***

Head ***

SOME COMPONENT COULD NOT BE PICKED UP

By picking up this component, depending on the pick up

accuracy, the component could hit the neighbor nozzle

with component.

Mount data ***

Component data *** Name ***

Head ***

SOME COMPONENTS ARE NOT POSSIBLE TO PICK

A picking up group without rotation-action could not in-

clude the FINE type component. Check the data.

Mount data ***

Component data *** Name ***

Head ***

SOME COMPONENT COULD NOT BE PICKED UP

Because the machine had picked up a component of FINE

type, the machine could not pickup another of FINE type.

Mount data ***

Component data *** Name ***

Head ***

SOME COMPONENT COULD NOT BE PICKED UP

By picking up this component, depending on the pick up

accuracy, the component could hit the neighbor nozzle

without component.

Mount data ***

Component data *** Name ***

Head ***

SOME COMPONENT COULD NOT BE PICKED UP

By picking up this component, depending on the pick up

accuracy, the component could hit the neighbor nozzle

without component during the rotating the component.

Mount data ***

Component data *** Name ***

Head ***

SOME COMPONENT COULD NOT BE PICKED UP

The machine had tryed to pickup components blongs dif-

ferent blocks.

Mount data ***

Component data *** Name ***

Head ***

NO COMPONENT FOR USE

A component is not available at this moment. Please con-

firming the component to be ready, and run again.

Mount data ***

Component data *** Name ***

Head ***

SOME COMPONENTS ARE NOT POSSIBLE TO PICK

If the head picks up the component, the component might

hit the lighting unit for fiducial mark. Please confirming

the data and run again.

Mount data ***

Component data *** Name ***

Head ***

SOME COMPONENT IS NOT MOUNTED YET

Because of too much mounting data, the searching op-

eration had been terminated by time-out. If this message

appears often, call up your agent.

NO COMPONENT FOR USE

A component is not available at this moment. Please con-

firming the component to be ready, and run again.

Mount data ***

Component data *** Name ***

Head ***

NO COMPONENT FOR USE

A component is not available at this moment. Please con-

firming the component to be ready, and run again.

Mount data ***

Component data *** Name ***

Head ***

ILLEGAL INTERNAL COUNTER

Hit key to re-calculate and continue.

Not Mounted data ***

Components left ***

Left in Blocks ***

It has been stopped resetting. Please try the RESET com-

mand again, and finish it.

CAN NOT EXECUTE COMMAND

Can not execute this command , because RESET is not

finished completely. Please try the RESET command

again, and finish it.

Processing mount data.

Please wait a moment.......

Mount data

Please set PCB.

Now adjusting correction of fiducial. Please wait a mo-

ment.......

Type of fiducial recognition is not selected. Please set

PCB Fiducial to “Use” in the PCB information.

CAN NOT EXECUTE COMMAND

Failed to execute this command, because the push-up

unit’s position is not enough low. Please execute this com-

mand after moving it down again,

Finished to change the active TABLE for Vision or Servo

System.

PROGRAMABLE PUSH PIN FILE READ ERROR.

Please check programable push pin file format.

Machine ***

File NO?\PPUDATA.STS

PCB DATA ERROR

There is a pin beyond the PCB X size.

Pin Pos.Row ***

Col ***

Ea -38

ERROR MESSAGES LIST

Ea07902

PCB DATA ERROR

There is a pin beyond the PCB Y size.

Pin Pos.Row ***

Col ***