YAMAHA errer code-a.pdf - 第8页

Ea - 8 ERROR MESSAGES LIST Ea Ea00204 | Ea00205 Ea00206 Ea00207 Ea00220 Ea00221 Ea00222 Ea00223 Ea00230 Ea00231 Ea00232 NOZZLE ST ATION ERROR There is no nozzle present for next sequence. Please check nozzle station data…

Ea -7

ERROR MESSAGES LIST

Ea00177

Ea00178

Ea00179

Ea00180

Ea00181

Ea00182

Ea00183

Ea00184

Ea00185

Ea00186

Ea00187

Ea00189

Ea00190

PCB DATA ERROR

When using component check function, you must pre-

pare some Mark data. But it doesn't exist or is not suit-

able.

Mount data 765

PreDispense data 1

Mark data 1

PCB DATA ERROR

CountOutStop must be same among alternative compo-

nents group.

Mount data 765

Component data 150

PCB DATA ERROR

Specified alternative component doesn't exist.

Mount data 765

Component data 150

PCB DATA ERROR

Feeder type of the component is different from the one of

the fixed component data.

Mount data 765

Component data 150

PCB DATA ERROR

Failed to read the fixed component data.

Mount data 765

Component data 150

PCB DATA ERROR

Specified fixed component doesn't exist.

Mount data 765

Component data 150

PCB DATA ERROR

The number of block repeat data exceeds limitation.

Maximum quantity is 765 .

PCB DATA ERROR

Component Name must be same among alternative com-

ponents group.

Mount data 765

Component data 150

PCB DATA ERROR

Usage of UpdateGroupNo must be same among alterna-

tive components group.

Mount data 765

Component data 150

PCB DATA ERROR

Local badmark position is outside moving area.

Mount data 3

Local Badmark data 5

Axes X

PCB DATA ERROR

No mark data available for the local badmark. Or the mark

data is not for badmark.

Mount data 7

Mark data 2

PCB DATA ERROR

Pickup position is outside moving area for soft landing

motion.

Mount data 765

Component data 150

Axes Z1

PCB DATA ERROR

Mount position is outside moving area for soft landing

motion.

Mount data 765

Component data 150

Axes Z1

(meaning)When using the component check function, which is a

special function there is a problem with the PCB data.

(cause)No mark information for bad marks has been specified in

the pre-dispensing data which contains the check coordinates.

(remedy)Create the mark information for the bad marks.

(meaning)Components which are organized in a series by the al-

ternative component settings do not have the same count stop set-

tings.

(cause)Alternative components in a series have different count stop

settings, so they will either stop or not stop.

(remedy)Standardize the settings.

(meaning)The specified alternative components do not exist.

(cause)There are no alternative components that match the set-

ting.

(remedy)When using alternative components, create data for the

alternative components corresponding to the specified number, or

do not specify alternative components.

(meaning)The feeder type specified in the PCB data is different

from that in the fixed components data.

(cause)A different type of feeder has been specified in the PCB

data from that specified in the fixed components data.

(remedy)Change one setting or the other so that they match.

(meaning)An error occurred when reading the fixed component data.

(cause)No fixed component data file exists in the machine, or the

fixed components data file has been destroyed.

(remedy)Copy the fixed component data from the backup disk.

(meaning)The specified component data does not exist.

(cause)The fixed component data corresponding to the fixed com-

ponent data number specified in the mounting data does not exist.

(remedy)Do not use the fixed component data, or create new fixed

component data.

(meaning)The number of block repeats exceeds the rated limit.

(cause)The specified number of block repeats exceeds the maxi-

mum limit of 512.

(remedy)Specify a number of block repeats that is 512 or less.

(meaning)The names of several components in a series of alterna-

tive components are different.

(cause)The names of all alternative components must be the same.

(remedy)Specify the names of alternative components linked in a

series so that all of the names are the same.

(meaning)In the component data for a series of alternative compo-

nents, there are some data which refer to fixed component data

and some which do not.

(cause)With alternative components, the fixed component data ref-

erences for series component data must be the same.

(remedy)Standardize the settings so that the fixed component data

is either referenced or not referenced for all of the alternative com-

ponent data in the series.

Please input correct position of Local Badmark.

(meaning)The mark data for the specified not an badmark does not

exist.

(cause)No mark data exists.

(remedy)Create the mark data.

(meaning)QFP components cannot be picked up using this mount-

ing method because of an incorrect setting in the pickup heights.

(cause)

(remedy)Check the settings for pickup heights.

(meaning)When the QFP mounting method is being used, the

mounting position height is not within the soft limit.

(cause)When the QFP mounting method is being used, the setting

for the mounting position height is outside of the soft limit.

(remedy)Check the setting for the mounting position height.

Ea00191

Ea00192

Ea00193

Ea00194

Ea00195

Ea00197

Ea00198

Ea00199

Ea00200

Ea00201

Ea00202

Ea00203

PCB DATA ERROR

No nozzle to attach to the head.

AxisTable A

Head 2

The number of possessed nozzle may not be enough.

Current nozzles on heads are different from the nozzles

necessary for this PCB.XY TABLE[Upper = Head No.,

Lower = Nozzle Type]

Head 1 2 3 4 5 6 7 8

Nzl. 1 1 1 2 2 2 2 2

Please check each heads equipped with nozzles as

shown below.

XY TABLE[Upper = Head No., Lower = Nozzle Type]

Head 1 2 3 4 5 6 7 8

Nzl. 1 1 1 2 2 2 2 2

PCB DATA ERROR

Component will interfere with other nozzles.

Mount data 765

Component data 150

Head 2

PCB DATA ERROR

PCB width is outside moving area.

Axes LW

PCB SIZE ERROR

Width of PCB is out of range.

SpDat[PLTnum_inf0](mm)

[PCB Width]

SpDat[PLTnum_inf1](mm)

Please set width of PCB again.

PCB DATA ERROR

No local badmark data is set to "Note" for executable

mounting data. During production, "Note" data is ignored.

So if you want to use local badmark function, set this "

Exec". If not, set "0" for BadMk in mounting data.

Mount Data 6

Local Badmark Data 3

PCB DATA ERROR

The PCB has too many mount data.

NOZZLE CHANGE ERROR

Failed to pick up a nozzle. Please check the sensor of

the nozzle station and adjust height, angle and position

data of the nozzle station.

Head No. 2

Station No. 11

NOZZLE CHANGE ERROR

Failed to store a nozzle. Please check the sensor of nozzle

station and adjust height, angle and position data of the

nozzle station.

Head No. 2

Station No. 11

DOWNLOAD WINDOW DATA ERROR

Failed to download the window data of the laser unit.

Please Power OFF the machine and check the connec-

tion of the laser unit.

NOZZLE STATION ERROR

One or more nozzle(s) are not present on the nozzle sta-

tion. Please check the sensors of the nozzle station and

insert the appropriate nozzle(s).

Head No. 2

(meaning)The specified nozzle cannot be attached to the head.

(cause)Because the setting for the number of nozzles is wrong, there

are not enough nozzles to be attached to the head, or it is not pos-

sible to use more than the current number of nozzles.

(remedy)If the nozzles are available, change the setting for the num-

ber of nozzles In any other case, create PCB data which does not

specify a head using the same nozzles.

(meaning)The nozzles which are currently attached are not the right

combination for the PCB about to be manufactured.

(cause)The wrong combination of nozzles was used when the setup

was changed.

(remedy)Attach the correct nozzles, following the instructions on

the display.

(meaning)This is the display showing the nozzle settings required

for the PCB about to be manufactured. It is not an error message.

(cause)None

(remedy)Check to make sure the nozzles which have been speci-

fied match those displayed before starting production.

(meaning)The component is interfering with the adjacent nozzle.

(cause)Because the component is large, it is interfering with the

nozzle next to it.

(remedy)Create the appropriate data and try again.

(meaning)The PCB width is not within the soft limit.

(cause)An attempt was made to use a PCB which is not within the

specifications, or there is something wrong with the PCB width set-

ting.

(remedy)Check the PCB width setting.

(meaning) PCB width is out of range being used.

(cause) PCB width has not been set within a range of $$$ mm (mini-

mum) to ### mm (maximum).

(remedy) Set PCB width to value within a range of $$$ mm to ###

mm.

If you want to use local badmark function. Set "skip?" parameter

"Exec". If you don't want to use set "0" in mount data

(meaning)The nr. of mount data exceeds limit.

(cause)The nr. of mount data exceeds limit.

(remedy)Delete some mount data. Or delete some skip data in block

repeat and etc.

(meaning)The nozzle could not be picked up.

(cause)The nozzle station sensor may be defective, or the height,

angle, or XY coordinates may not have been correctly adjusted in

the nozzle station information.

(remedy)Adjust the sensor. Also, re-adjust the nozzle position, angle,

and height in the nozzle station information.

(meaning)An error occurred when housing the nozzle.

(cause)The nozzle station sensor may be defective, or the height,

angle, or XY coordinates may not have been correctly adjusted in

the nozzle station information.

(remedy)Check the operation of the nozzle station sensor. Also, re-

adjust the nozzle position, angle, and height in the nozzle station

information.

(meaning)An error occurred when transferring window data to the

laser recognition unit.

(cause)An error occurred in sending the data because of noise or

another factor, or the laser recognition unit has become disconnected

from the I/O board.

(remedy)Check the laser recognition unit connections, and then turn

the power supply off and try running the machine again. Check to

see how often the problem occurs, and contact the manufacturer if

necessary.

(meaning)Several nozzles are produced from the nozzle station of

the specified head.

(cause)The nozzle station sensor may be defective, or several

nozzles have been removed from the nozzle station.

(remedy)Make sure the correct nozzles are stored in the nozzle

station, or check the operation of the nozzle station sensor.

Ea -8

ERROR MESSAGES LIST

Ea00204

Ea00205

Ea00206

Ea00207

Ea00220

Ea00221

Ea00222

Ea00223

Ea00230

Ea00231

Ea00232

NOZZLE STATION ERROR

There is no nozzle present for next sequence. Please

check nozzle station data.

Head No. 2

Station No. 11

NOZZLE STATION ERROR

There is more than one nozzle for next sequence. Please

check sensors of the nozzle station and insert the appro-

priate nozzle(s).

Head No. 2

Station No. 11

DATA ERROR

The next mount sequence specifies that more than three

heads are used or the head number used is 3 or more.

Please check the mount data.

DATA ERROR

The next mount sequence specifies that more than three

heads are used or the head number used is 3 or more.

Please check the mount data.

BACKLIGHT POSITION ERROR

1. Ensure all nozzles not in use are in station.

2. Ensure the sensor knows nozzles are there.

3. Push EMG sw. and pull up no.2 head to up-end, push

down no.1 head to lower pos.

4. In case the step 1-3 had not solved problem, Please

move backlight to right position by CHANGE BACKLIGHT

command.

NOZZLE CHANGE ERROR

Now, head is picking the component. Head can't change

the nozzle.

OPERATION ERROR

1. Ensure all nozzles not in use are in station.

2. Ensure the sensor knows nozzles are there.

3. Push EMG sw. Check the safety of head, nozzles,

nozzle station.

4. In case the step 1-3 had not solved problem, Please

ensure safety by manual.

NOZZLE STATION CLAMPING ERROR

Unable to clamp nozzles in the nozzle station.

Correct the condition of the nozzle station.

4-Point Fiducial Data Error

Fiducial No.5

Setting of [Type] is not correct. Please set like this,

No. 5 --> [4Local-M]

No. 6 --> [4Local-S]

4-Point Fiducial Data Error

Fiducial No.5

Setting of [Mark] is not correct. Please set same number.

4-Point Fiducial Data Error

Fiducial No.5

Distance between point and another point is too short.

Please set this distance more than 5(mm). Please set

coordinates of 4-point again.

(meaning)The nozzle intended for use is not in the nozzle station.

(cause)The nozzle which is planned for use has not been specified

in the nozzle station information.

(remedy)Check the settings in the nozzle station information.

(meaning)The nozzle station contains more than one of the same

nozzle.

(cause)Two of the same nozzle have been specified in the nozzle

station information.

(remedy)Check the nozzle station information.

(meaning)A head number of 3 or higher has been specified in the

mounting data for a mounter which has only two heads.

(cause)A head number of 3 or more has been specified.

(remedy)Change the head number in the placing data to 1 or 2.

(meaning)Vision recognition is specified with head 2.

(cause)With this machine, vision recognition cannot be carried out

using head 2.

(remedy)Change the head number to 1, or change to laser recog-

nition.

(meaning)The backlighting illumination is dangerously positioned.

(cause)When an attempt was made to change nozzles, the nozzles

could not be changed because the position of the backlighting illu-

mination was dangerous.

(remedy)Check to see that all of the nozzles are in the nozzle sta-

tion, and that the sensor reacts to all of the nozzles in the nozzle

station. Next, press the Emergency Stop button and move head 2

to its upper end and head 1 below the backlighting illumination

Then use the backlighting illumination movement command to move

the backlighting illumination to the right.

(meaning)The nozzle cannot be replaced because a component

has been picked up.

(cause)Two causes are possible: the head vacuum is on, or the

head vacuum is on and a component has been detected by the

vacuum level sensor.

(remedy)Remove the component from the nozzle or turn off the

head vacuum.

Accident happened for YV-120 machine Nozzle changing is failed.

According to the message and recover this accident

(meaning)Although the upper plate of the nozzle station slides and

two sensor for both edge (only single side for YVL80) detect the

actual action of the plate, at least 1 sensor do not response to the

command to slide the plate.

(cause)qPlate is mechanically stuck. The position or the sensitivity

of the sensor is not adjusted.

(remedy)Repair the sliding plate, or adjust the sensor.

Please set fiducial data according to "Error Message".

Please set 4 point fiducial data like shown in "Error Message".

Ea00233

Ea00234

Ea00235

Ea00236

Ea00237

Ea00238

Ea00239

Ea00240

Ea00241

Ea00242

Ea00243

Ea00244

Ea00245

4-Point Fiducial Data Error

Fiducial No.5

In quadrilaterals which is composed of 4-point fiducial,

distance between one point and one side of quadrilater-

als is less than 5(mm). Please set coordinates of 4-point

again.

4-Point Fiducial Data Error

Fiducial No.5

In quadrilaterals which is composed of 4-point fiducial,

there is interior angle which is over 180 degree. sage.

Please set coordinates of 4-point again.

4-Point Fiducial Data Error

Fiducial No.5

It is impossible to use this fiducial number which is se-

lected in this Mount Data, because this data is [4Local-

S]. Please use [4Local-M] Fiducial number of 4-point fi-

ducial.

4-Point Fiducial Data Error

Fiducial No.4

It is impossible to use this fiducial data, because this data

is [Note]. Please change from [Note] to [Exec].

PCB DATA ERROR

Mount data No.4

Fiducial data No.6

It is impossible to use this fiducial data, because this data

is [Note]. Please change from [Note] to [Exec].

4-Point Fiducial Data Errorpe Error

Mount data No. 6

Fiducial data No. 2

Coordinate of mount point is out of range of 4-point-fidu-

cial. to use this function in Please don't use this 4-point

fiducial for this mount point.

Data Warning

The piece of block that you defined in PCB Information is

different from piece of local badmark.

In this case, machine cannot count Block Numbers in

Production History. If you want to count Block Numbers,

change number of block in PCB Information.

PCB DATA ERROR

No mark data available for the local fiducial. Or the mark

data is not for fiducial.

Mount Data 1

Mark Data 2

PCB DATA WARNING

Height of component is out of range for "Multi Cam".

Component Data 2

It may be impossible to recognize this component by us-

ing "Multi.Cam". It is necessary to check whether this

component is able to be recognized by using "Multi.Cam"

in [ADJUST ASSISTANT]. To continue "Data-Check",

press any key.

MARK DATA WARNING

Templet image can't be downloaded to the vision.

•Did you create templet image of target mark?

•Don't you make too many mark data in one PCB?

•Don't you want to use too many kind of mark?

PCB DATA ERROR

Effective data was not found. There is no data to execute.

Use 'PASS'.

PCB DATA ERROR

There is no mark pattern data. Some pattern matching

function is used for fiducial mark, but it has no pattern

matching data. This data was made by executing of [Ad-

just Assistant] in Mark Information.

PCB DATA ERROR

This component body height is too high. So this compo-

nent is cannot recognize by equipped camera.

Mount Data 10

Component Data 5

Please set 4 point fiducial data like shown in "Error Message".

Set same number of block in PCB Information as total local badmark

number.

(meaning)The mark data for the specified not an fiducial does not

exist.

(cause)No mark data exists.

(remedy)Create the mark data.

(meaning)It may be impossible to recognized this component by

using "Multi.Cam" because height of this component is out of range

for "Multi.Cam"

(remedy)Please check recognition of this component in [ADJUST

ASSISTANT].

(meaning) No effective data in the PCB data.

(remedy) Use "PASS".

(meaning) There is no data for pattern matching.

(remedy) Make data for pattern matching of fiducial mark in mark

information.

(meaning) This component is too high for its height.

(remedy) Check camera coordinate data.

Ea -9

ERROR MESSAGES LIST

Ea00246

Ea00247

Ea00248

Ea00249

Ea00250

Ea00251

Ea00260

Ea00261

Ea00262

Ea00270

Ea00271

Ea00272

Ea00273

PCB DATA ERROR

This component body size is too big.gh. So this compo-

nent is cannot recognize by equipped camera.

Mount Data 10

Component Data 5

PCB DATA ERROR

"Mount Action" reserved component number is "Fine

Type", but fine mode reserved head is "Impossible".

Mount data 10

Head number 5

Please reserve component number not "Fine Type", etc.

COMPONENT DATA ERROR

Feeder Type for this component was not defined. Specify

the feeder type data in Component Info.

Mount Data 12

Component Data 3

COMPONENT DATA ERROR

Feeder Position must be "Teaching" or "Relative" for stick

feeder component. Input Feeder Pos_X,Y:

In case "Teaching", from the datum of machine origin.

In case "Relative", from the datum of 8mm tape feeder

pickup position.

Component data 3

COMMUNICATION ERROR

Failure of communicating with LOADER. One of the fol-

lowing could cause this error:

q LOADER or UNROADER is turned off power.

w LOADER or UNROADER is in emergency stop.

e LOADER or UNROADER is in auto-running.

r LOADER or UNROADER has already received PCB

width data after power-on.

If you don't want to repeat communicating with LOADER

Please push [TAB] keys.

If you want to repeat communicating with LOADER Please

push other keys.

DUMP STATION DATA ERROR

The feeder number used for dump station is not defined.

It must not be 0. Please confirm it.

DUMP STATION DATA ERROR

The feeder number used for dump station is not suitable.

In case of SM112, if this number for A-table is defined

more than 101, then this error will happen. Please con-

firm it.

DUMP STATION DATA ERROR

The X,Y position of dump station is not suitable. All heads

must be reach on this position, but the current coordi-

nate is out of it. In case of SM112, dump station may be

set about from 16 to 40 feeder location number. Please

correct X,Y coordinate of dump station.

PCB DATA ERROR

There is no dispense head for dot dispensing. Check the

head type and nozzle type in 3-2-A1-[Head Offset].

Dot Dispense data 11

PCB DATA ERROR

Dot dispensing position is outside moving area.

Dot Dispense data 3

Axes X

Checking dot dispensing data. Please wait a moment.......

Dot Dispense data 4

Block number 3

PCB DATA ERROR

Local badmark position of dispense data is outside mov-

ing area.

Dispense data 4

Local Badmark data 3

Axes X

(meaning) This component is too big for its height.

(remedy) Check camera coordinate data.

(meaning) The head "FineMode" is "Impossible " cannot act by

"FineType".

(cause) Reserved head is FineMode Impossible, but reserved com-

ponent is "FineType".(remedy) Please do one of following ways.

• Change headnum Finemode Possible.

• Change component not Finetype.

• Change component data other type

• Change "FineMode" "Possible".

(meaning) Feeder Type was not defined yet.

(cause) It seems that component package parameter was changed

after feeder type was defined. So, feeder type was changed to "Not

Defined"

(remedy) Select right feeder type.

(meaning) Feeder position is set to "Automatic" but this is a stick

feeder component.

(cause) Stick feeder must set its feeder set position to "Teaching"

or "Relative".

(remedy) Set right setting for Feeder Position (Teaching or Rela-

tive). And input Feeder Pos_X,Y parameter.

In case "Teaching", input from the datum of machine origin

In case "Relative", input from the datum of 8mm tape feeder pick

up position

(meaning) Failure of communicating with LOADER.

(cause) Cause is shown in "Error Message".

(remedy)Please remove cause.

This message is not "Error Message".

(meaning)

(cause)None

(remedy)None

(meaning)Feeder number for dump station is 0.

(cause)Feeder number for dump station must be more than 1.

(remedy)Please set number again.

(meaning)Feeder number for dump station is 0.

(cause)There is no dump station on the table which feeder for a

component is attached.

(remedy)If no dump station, please abort to use. Please change

feeder location on same table to dump station. Please set more

than 1 in feeder number for dump station.

(meaning)Feeder number for dump station is 0.

(cause)Because all heads must be reached on this coordinate, but

current pos. is out of it.

(remedy)Please change the position of dump station, and change

the coordinate again.

(meaning)Illegal dispense head was defined in dot dispense data.

(cause)The head does not exist, or the head number is not dis-

pense head.

(remedy)Please input right head number.

(meaning)X,Y position of Dot Dispense data is out of moving area.

(cause)The position is out of software limit.

(remedy)Please set right X, Y position or set right head number.

(meaning)Data check about dot dispensing data is being now car-

ried on.

(cause)This is not error message.

(remedy)Please wait until data check finish.

(meaning)Local badmark position defined in Dot dispense data is

out of moving Area.

(cause)Local badmark position is out of software limit.

(remedy)Please input right local badmark position.

Ea00274

Ea00275

Ea00276

Ea00277

Ea00278

Ea00279

Ea00280

Ea00281

Ea00282

Ea00283

Ea00284

Ea00285

Ea00286

Ea00287

PCB DATA ERROR

There is no local badmark data for the dot dispense.

Dispense Data 4

Local Badmark Data 3

PCB DATA ERROR

There is no mark data of local badmark available for the

dot dispense data.

Dot Dispense Data 4

Local Badmark data 3

Mark data 5

PCB DATA ERROR

No local badmark data is set to "Note" for executable dot

dispense data. During production, "Note" data is ignored.

So if you want to use local badmark function, set this "

Exec". If not, set "0" for BadMk in dot dispensing data.

Dot Dispense Data 4

Local Badmark Data 3

4-Point Fiducial Data Error

Dot Dispense Data No 4

Fiducial Data No. 3

It is impossible to use this Fiducial number which is se-

lected in this Dot Dispense Data, because this data is

[4Local-S]. Please use [4Local-M] Fiducial number of 4-

point fiducial.

PCB DATA ERROR

Dot Dispense Data No. 4

Fiducial data No. 3

It is impossible to use this fiducial data, because this data

is [Note]. Please change from [Note] to [Exec].

PCB DATA ERROR

No fiducial data available for the dot dispense local fidu-

cial.

Dot Dispense data 4

Fiducial data 3

PCB DATA ERROR

No mark data available for the dot dispense local fidu-

cial.

Dot Dispense data 10

Fiducial data 5

Mark data 2

Checking pre dispensing data.

Please wait a moment.......

Pre Dispense data 4

Block number 3

PCB DATA ERROR

Pre dispensing position is outside moving area.

Pre Dispense data 3

Axes X

PCB DATA ERROR

There is no dispense head for pre dispensing.

Pre Dispense data 11

Head number 4

PCB DATA ERR

It is impossible to use "Point Fiducial" for Dispense. Please

check the mount data or fiducial data.

Dot Dispense data 5

Fiducial data 3

PCB DATA ERR

Illegal unit for pre dispensing. Defined unit for that head

is out of range for adequate unit.

Pre Dispense data 5

Head number 3

Unit 30

PCB DATA ERR

Illegal unit for dot dispensing. Defined unit for that head

is out of range for adequate unit.

Dot Dispense data 4

Head number 2

Unit 70

DOT STATION PITCH ERR

Dot station pitch either X direction or Y direction must be

set "0". Please check the dot station pitch X,Y.

(meaning)Local badmark data for dot dispense data does not ex-

ist.

(cause)Local badmark data have not defined in local badmark in-

formation yet.

(remedy)Please define local badmark data, if you use this function.

(meaning)There is not mark data for local badmark.

(cause)The mark data of Local badmark data for dot dispense have

not defined.

(remedy)Please define mark data in mark information for local

badmark of dot dispense data.

(meaning)The local badmark data of the dot dispense data is "Note"

data.

(cause)Local badmark that is "Note" is ignored during in running

condition.

(remedy)Please input "Exec" data of local badmark for dot dispense

data.

(meaning)The fiducial number of dot dispense data is "4Local-S"

data.

(cause)"4Local-S" data is not for setted in fiducial number of dot

dispense data.

(remedy)Please set "4Local-M" number.

(meaning)The fiducial number of dot dispense

(cause)"Note" data is ignored in running.

(remedy)Set "Exec" from "Note".

(meaning)There is no fiducial data for dot dispense data.

(cause)The fiducial number of dot dispense has not defined yet.

(remedy)Please make fiducial data

(meaning)There is no mark data for fiducial data of dot dispense

data.

(cause)The mark data was not made yet.

(remedy)Please make mark data of fiducial of dot dispense, or if

you have already prepared mark data, set that mark number.

(meaning)Data check about pre dispensing data is being now

carryed on.

(cause)This is not error message.

(remedy)Please wait until data check finish.

(meaning)X,Y position of Pre Dispense data is out of moving area.

(cause)The position is out of software limit.

(remedy)Please set right X, Y position or set right head number.

(meaning)Illegal dispense head was defined in pre dispense data.

(cause)The head does not exist, or the head number is not dis-

pense head.

(remedy)Please input right head number.

Please don't use "Point Fiducial" for Dispense.

Non adequate dispensing unit was defined. Please set head num-

ber "0", to select head automatically, or input adequate value for

dispensing unit that is defined in NOZZLE-SPEC Information.

Non adequate dispensing unit was defined. Please set head num-

ber "0", to select head automatically, or input adequate value for

dispensing unit that is defined in NOZZLE-SPEC Information.

(meaning)DOT STATION PITCH ERR

(cause)Dot station pitch either X direction or Y direction must be

set "0".

(remedy)Please check the dot station pitch X,Y.