00198500-02_VD_711.1_R18-1_DE_EN.pdf - 第33页

Station Software 71 1.1 (R18 - 1) / Versio n Description 05/2018 Edition 33 D1 - 144666909 Automatic pin reco gnition with 8mm f eeder: OIS erro neously was counti ng a rejec t. D1 - 144698005 A component was m arked for…

Station Software 711.1 (R18-1) / Version Description 05/2018 Edition

D1-141676541

The gripper got lost and the machine reported 30482 Z axis is beyond

maximum position, position is in empty space, segment: 2

but did not stop.

D1-142007061

eSW: conveyor: changing conveyor mode from double back to single did not

work.

D1-142180007

Measuring all components after placement lead to the error message: y

axis 1 power supply not sufficient

D1-142505151

The station reported 40034 CAUTION: Do not move gantry! The

head lost a nozzle

although the gripper was not lost.

D1-142765001

Fill level change

after

consumed

event from station caused problems.

D1-142800301

Sporadically the station SW stopped during placement with error message

30016 Unhandled exception error

D1-142915801 During production run there was no placement in placement area 2.

D1-143004545 The station could not be stopped and had to be switched off.

D1-143141501

The current of the lifting table motor was too low at conveyor motor

verification.

D1-143195601

Suddenly the station software did not react any longer and had to be

rebooted.

D1-143204201

eSW: The lifting table moved downwards into the mechanical limit as soon as

a board arrived in the placement area.

D1-143231401

The multistep calibration stopped with an error message when the results

were saved.

D1-143475401

The SIPLACE Pro components which were assigned to specific reference

designators differed to those in SIPLACE Pro.

D1-143605001 Plausibility check showed wrong error message.

D1-143635102 eSW: the overlapping of the X- and Z-axes during pick up was not correct.

D1-143683801

A new program was downloaded with activated snap in verification.

Afterwards the snap selection ran endlessly. Anschließend lief die Snap-

Auswahl in Endlosschleife.

D1-143697601 The polarity check during re-filling did not work.

D1-143744601 The X feeder index LED did not show the correct status.

D1-143783201

The whispering of board barcode was active although the machines were not

defined as a cluster.

D1-143958512 The component in the tray could not be reached.

D1-144006701

The software hung up when the changes of OSC component teaching were

saved.

D1-144031036

The station GUI was not refreshed after download. The previous job was

displayed on the screen.

D1-144063301

A wide connector on TH segment 2 was wiped off by the aperture collar of

segment 1.

D1-144172401 Vision dumps could not be filtered by location.

D1-144388801

During preparation work for new production there was the error message

32602 The software has stopped unexpectedly. Shut down

Windows, then restart the station

D1-144618801 Components were not available for teaching.

Station Software 711.1 (R18-1) / Version Description 05/2018 Edition

D1-144666909

Automatic pin recognition with 8mm feeder: OIS erroneously was counting a

reject.

D1-144698005

A component was marked for teaching before placement. When the new

position was saved the software hung up.

D1-144711401 The thresholds were not recalculated when the recipe was changed.

D1-144728801 The station software hung up after a mechanical change of the conveyor.

D1-144830807 The nozzle could not be returned if there was still a component on the nozzle.

D1-144854701

eSW: the motor for the width adjustment could not be calibrated (SX 1/2 with

single conveyor).

D1-144860701

Error message 34036 Y axis mapping data not activated when Y

mapping was executed and the mapping data should be restored.

D1-144868153

The station software stopped during/after placement with error message

30016 Unhandled exception error

D1-144890453

Dirty glue feeder lead to error message 34432 Fatal error, maximum

number of retries reached

D1-145008101 Error message:

34641 Cannot reject nozzle

D1-145043932

When a gantry did no longer travel over the current board, because high

components were placed by the head of the other gantry, the inapprehensible

message 32539 Beware of collision with high components on

board

was displayed.

D1-145070937 The DUMP archive was not deleted after an auto bug report.

D1-145384201 Unexpected software malfunction - the application had to be closed.

D17845-17170

When we taught and accepted the placement position, the teach offset

x/y/angle in the placement list changed automatically even though we did not

change it.

D17933-41707

The CPP head moved continuously left and right without picking up the

component on the waffle pack of the WPC6.

D18093-21501 The software hung up with the error message that ISS did not respond.

D18093-22703

Sporadically the station SW stopped during placement with the error

messages 30016 Unhandled exception error and 32602 The

software has stopped unexpectedly

D18093-22757 Error message

34488 Placement head is unable to continue

D18170-42001 There were inconsistent nozzle scan results and misleading error messages.

D18364-1423

The production stopped without any error message after having recognized

the fiducials.

D18400-101

Gantry1 stopped with message 32535 Checking nozzle

configuration: C&P20 P Head

D18403-209 eSW: The X-axis motor hit the buffer mount of the X-axis.

Table 9-6: Corrected errors station software version 710.1 Patch 4

Station Software 711.1 (R18-1) / Version Description 05/2018 Edition

710.1 Patch 2

Error no. Error description

D1-139125591 At a TX machine, an error message was displayed that the weight dependent

motor current was too big.

D1-140020401 There was an unhandled exception when a tray was used on a carrier.

D1-140048801 The reject bin configuration was not displayed correctly on the GUI.

D1-141199449 The station software stopped during / after placement with error message

30016 Unhandled exception error

D1-141376801 When the embedded Software was updated, error message 30554

Subsystem is not responding (dp axis)

was displayed.

D1-141376849 The state of the board was displayed even if the board had reached the output

conveyor.

D1-141386801 The component sensor data was invalid and could not be restored.

D1-141541301 Status 30622 Nozzle missing was not reset for the nozzle.

D1-141564601 Coplan-MCT was not possible: instead of using the SST33 camera the SST25

was used. With this camera the calibration failed.

D1-141619501 After a machine restart, the message 30450 WPC2 unspecified

hardware error

was displayed.

D1-141670801

D1-141138729

D1-142037601

eSW: After restarting the machine, the message 30555 Subsystem is

not activated (main distributor) was displayed sporadically, but

machine worked without any problems.

D1-141993601 The button to change the acceleration of JTF-ML2 was missing.

D1-142003201 The Edit pickup point function should get a separate user level.

D1-142176533 The machine stopped during production.

D1-142207343 It was not possible to change the filling level of the JTF.

D1-142229001 During the shutdown of the machine, error message unhandled exception

error

was displayed.

D1-142248701 C&P20 M2 segments were not recognized.

D1-142266401 Along with the "LBO 1500" option, support pins could not be set.

D1-142276101 eSW: TX micron with station software 710.1: Along with vacuum tooling there

was always an error with the lifting table motors during board loading.

D1-142283901 Several problems with vacuum tooling with station software 710.1.

D1-142290001 Error message 30977 Timeout acquiring resources was displayed

and the board disappeared on the GUI.

D1-142328345

D1-142328387

D1-142328735

Teaching the pickup position during production resulted in a software hang-up.

D1-142441301

D1-142325401

eSW: The x-axis parametrization could not be executed any longer.